io.c
/*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
*
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/device.h>
#include <linux/string.h>
#include <linux/slab.h>
#include <linux/fs.h>
#include <linux/platform_device.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/firmware.h>
#include <linux/io.h>
#include "io.h"
#ifdef CONFIG_B4860G100
static struct gpiobus gbus;
#endif /* CONFIG_B4860G100 */
static inline void byte0_out(unsigned char data);
static inline void byte1_out(unsigned char data);
static inline void xl_cclk_b(int32_t i);
/* Assert and Deassert CCLK */
void xl_shift_cclk(int count)
{
int i;
for (i = 0; i < count; i++) {
xl_cclk_b(1);
xl_cclk_b(0);
}
}
int xl_supported_prog_bus_width(enum wbus bus_bytes)
{
switch (bus_bytes) {
case bus_1byte:
break;
case bus_2byte:
break;
default:
pr_err("unsupported program bus width %d\n",
bus_bytes);
return 0;
}
return 1;
}
/* Serialize byte and clock each bit on target's DIN and CCLK pins */
void xl_shift_bytes_out(enum wbus bus_byte, unsigned char *pdata)
{
/*
* supports 1 and 2 bytes programming mode
*/
if (likely(bus_byte == bus_2byte))
byte0_out(pdata[0]);
byte1_out(pdata[1]);
xl_shift_cclk(1);
}
/*
* generic bit swap for xilinx SYSTEMMAP FPGA programming
*/
static inline unsigned char bitswap(unsigned char s)
{
unsigned char d;
d = (((s&0x80)>>7) | ((s&0x40)>>5) | ((s&0x20)>>3) | ((s&0x10)>>1) |
((s&0x08)<<1) | ((s&0x04)<<3) | ((s&0x02)<<5) | ((s&0x01)<<7));
return d;
}
#ifdef CONFIG_B4860G100
/*
* ======================================================================
* board specific configuration
*/
static inline void mpc85xx_gpio_set_dir(
int32_t port,
uint32_t mask,
uint32_t dir)
{
dir |= (in_be32(gbus.r[port]+GPDIR) & ~mask);
out_be32(gbus.r[port]+GPDIR, dir);
}
static inline void mpc85xx_gpio_set(int32_t port, uint32_t mask, uint32_t val)
{
/* First mask off the unwanted parts of "dir" and "val" */
val &= mask;
/* Now read in the values we're supposed to preserve */
val |= (in_be32(gbus.r[port]+GPDAT) & ~mask);
out_be32(gbus.r[port]+GPDAT, val);
}
static inline uint32_t mpc85xx_gpio_get(int32_t port, uint32_t mask)
{
/* Read the requested values */
return in_be32(gbus.r[port]+GPDAT) & mask;
}
static inline void mpc85xx_gpio_set_low(int32_t port, uint32_t gpios)
{
mpc85xx_gpio_set(port, gpios, 0x00000000);
}
static inline void mpc85xx_gpio_set_high(int32_t port, uint32_t gpios)
{
mpc85xx_gpio_set(port, gpios, 0xFFFFFFFF);
}
static inline void gpio_set_value(int32_t port, uint32_t gpio, uint32_t value)
{
int32_t g;
g = 31 - gpio;
if (value)
mpc85xx_gpio_set_high(port, 1U << g);
else
mpc85xx_gpio_set_low(port, 1U << g);
}
static inline int gpio_get_value(int32_t port, uint32_t gpio)
{
int32_t g;
g = 31 - gpio;
return !!mpc85xx_gpio_get(port, 1U << g);
}
static inline void xl_cclk_b(int32_t i)
{
gpio_set_value(XL_CCLK_PORT, XL_CCLK_PIN, i);
}
void xl_program_b(int32_t i)
{
gpio_set_value(XL_PROGN_PORT, XL_PROGN_PIN, i);
}
void xl_rdwr_b(int32_t i)
{
gpio_set_value(XL_RDWRN_PORT, XL_RDWRN_PIN, i);
}
void xl_csi_b(int32_t i)
{
gpio_set_value(XL_CSIN_PORT, XL_CSIN_PIN, i);
}
int xl_get_init_b(void)
{
return gpio_get_value(XL_INITN_PORT, XL_INITN_PIN);
}
int xl_get_done_b(void)
{
return gpio_get_value(XL_DONE_PORT, XL_DONE_PIN);
}
/* G100 specific bit swap and remmap (to gpio pins) for byte 0 */
static inline uint32_t bit_remap_byte0(uint32_t s)
{
uint32_t d;
d = (((s&0x80)>>7) | ((s&0x40)>>5) | ((s&0x20)>>3) | ((s&0x10)>>1) |
((s&0x08)<<1) | ((s&0x04)<<3) | ((s&0x02)<<6) | ((s&0x01)<<9));
return d;
}
/*
* G100 specific MSB, in this order [byte0 | byte1], out
*/
static inline void byte0_out(unsigned char data)
{
uint32_t swap32;
swap32 = bit_remap_byte0((uint32_t) data) << 8;
mpc85xx_gpio_set(0, 0x0002BF00, (uint32_t) swap32);
}
/*
* G100 specific LSB, in this order [byte0 | byte1], out
*/
static inline void byte1_out(unsigned char data)
{
mpc85xx_gpio_set(0, 0x000000FF, (uint32_t) bitswap(data));
}
/*
* configurable per device type for different I/O config
*/
int xl_init_io(void)
{
struct device_node *np;
const u32 *p_reg;
int reg, cnt;
cnt = 0;
memset(&gbus, 0, sizeof(struct gpiobus));
for_each_compatible_node(np, NULL, "fsl,qoriq-gpio") {
p_reg = of_get_property(np, "reg", NULL);
if (p_reg == NULL)
break;
reg = (int) *p_reg;
gbus.r[cnt] = of_iomap(np, 0);
if (!gbus.r[cnt]) {
pr_err("not findding gpio cell-index %d\n", cnt);
return -ENODEV;
}
cnt++;
}
mpc85xx_gpio_set_dir(0, 0x0002BFFF, 0x0002BFFF);
mpc85xx_gpio_set_dir(1, 0x00240060, 0x00240060);
gbus.ngpio = cnt;
return 0;
}
#else /* placeholder for boards with different config */
void xl_program_b(int32_t i)
{
return;
}
void xl_rdwr_b(int32_t i)
{
return;
}
void xl_csi_b(int32_t i)
{
return;
}
int xl_get_init_b(void)
{
return -1;
}
int xl_get_done_b(void)
{
return -1;
}
static inline void byte0_out(unsigned char data)
{
return;
}
static inline void byte1_out(unsigned char data)
{
return;
}
static inline void xl_cclk_b(int32_t i)
{
return;
}
/*
* configurable per device type for different I/O config
*/
int xl_init_io(void)
{
return -1;
}
#endif /* CONFIG_B4860G100 */