Kconfig
menu "Passive cards"
config ISDN_DRV_HISAX
tristate "HiSax SiemensChipSet driver support"
select CRC_CCITT
---help---
This is a driver supporting the Siemens chipset on various
ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles
S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many
compatibles).
HiSax is just the name of this driver, not the name of any hardware.
If you have a card with such a chipset, you should say Y here and
also to the configuration option of the driver for your particular
card, below.
if ISDN_DRV_HISAX!=n
comment "D-channel protocol features"
config HISAX_EURO
bool "HiSax Support for EURO/DSS1"
help
Say Y or N according to the D-channel protocol which your local
telephone service company provides.
The call control protocol E-DSS1 is used in most European countries.
If unsure, say Y.
config DE_AOC
bool "Support for german chargeinfo"
depends on HISAX_EURO
help
If you want that the HiSax hardware driver sends messages to the
upper level of the isdn code on each AOCD (Advice Of Charge, During
the call -- transmission of the fee information during a call) and
on each AOCE (Advice Of Charge, at the End of the call --
transmission of fee information at the end of the call), say Y here.
This works only in Germany.
config HISAX_NO_SENDCOMPLETE
bool "Disable sending complete"
depends on HISAX_EURO
help
If you have trouble with some ugly exchanges or you live in
Australia select this option.
config HISAX_NO_LLC
bool "Disable sending low layer compatibility"
depends on HISAX_EURO
help
If you have trouble with some ugly exchanges try to select this
option.
config HISAX_NO_KEYPAD
bool "Disable keypad protocol option"
depends on HISAX_EURO
help
If you like to send special dial strings including * or # without
using the keypad protocol, select this option.
config HISAX_1TR6
bool "HiSax Support for german 1TR6"
help
Say Y or N according to the D-channel protocol which your local
telephone service company provides.
1TR6 is an old call control protocol which was used in Germany
before E-DSS1 was established. Nowadays, all new lines in Germany
use E-DSS1.
config HISAX_NI1
bool "HiSax Support for US NI1"
help
Enable this if you like to use ISDN in US on a NI1 basic rate
interface.
config HISAX_MAX_CARDS
int "Maximum number of cards supported by HiSax"
default "8"
help
This option allows you to specify the maximum number of cards which
the HiSax driver will be able to handle.
comment "HiSax supported cards"
config HISAX_16_0
bool "Teles 16.0/8.0"
depends on ISA
help
This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8
and many compatibles.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port/shmem settings.
config HISAX_16_3
bool "Teles 16.3 or PNP or PCMCIA"
help
This enables HiSax support for the Teles ISDN-cards S0-16.3 the
Teles/Creatix PnP and the Teles PCMCIA.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_TELESPCI
bool "Teles PCI"
depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
help
This enables HiSax support for the Teles PCI.
See <file:Documentation/isdn/README.HiSax> on how to configure it.
config HISAX_S0BOX
bool "Teles S0Box"
help
This enables HiSax support for the Teles/Creatix parallel port
S0BOX. See <file:Documentation/isdn/README.HiSax> on how to
configure it.
config HISAX_AVM_A1
bool "AVM A1 (Fritz)"
depends on ISA
help
This enables HiSax support for the AVM A1 (aka "Fritz").
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_FRITZPCI
bool "AVM PnP/PCI (Fritz!PnP/PCI)"
depends on BROKEN || !PPC64
help
This enables HiSax support for the AVM "Fritz!PnP" and "Fritz!PCI".
See <file:Documentation/isdn/README.HiSax> on how to configure it.
config HISAX_AVM_A1_PCMCIA
bool "AVM A1 PCMCIA (Fritz)"
help
This enables HiSax support for the AVM A1 "Fritz!PCMCIA").
See <file:Documentation/isdn/README.HiSax> on how to configure it.
config HISAX_ELSA
bool "Elsa cards"
help
This enables HiSax support for the Elsa Mircolink ISA cards, for the
Elsa Quickstep series cards and Elsa PCMCIA.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_IX1MICROR2
bool "ITK ix1-micro Revision 2"
depends on ISA
help
This enables HiSax support for the ITK ix1-micro Revision 2 card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_DIEHLDIVA
bool "Eicon.Diehl Diva cards"
help
This enables HiSax support for the Eicon.Diehl Diva none PRO
versions passive ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_ASUSCOM
bool "ASUSCOM ISA cards"
depends on ISA
help
This enables HiSax support for the AsusCom and their OEM versions
passive ISDN ISA cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_TELEINT
bool "TELEINT cards"
depends on ISA
help
This enables HiSax support for the TELEINT SA1 semiactiv ISDN card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_HFCS
bool "HFC-S based cards"
depends on ISA
help
This enables HiSax support for the HFC-S 2BDS0 based cards, like
teles 16.3c.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_SEDLBAUER
bool "Sedlbauer cards"
help
This enables HiSax support for the Sedlbauer passive ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
config HISAX_SPORTSTER
bool "USR Sportster internal TA"
depends on ISA
help
This enables HiSax support for the USR Sportster internal TA card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_MIC
bool "MIC card"
depends on ISA
help
This enables HiSax support for the ITH MIC card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_NETJET
bool "NETjet card"
depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
help
This enables HiSax support for the NetJet from Traverse
Technologies.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_NETJET_U
bool "NETspider U card"
depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
help
This enables HiSax support for the Netspider U interface ISDN card
from Traverse Technologies.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_NICCY
bool "Niccy PnP/PCI card"
help
This enables HiSax support for the Dr. Neuhaus Niccy PnP or PCI.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_ISURF
bool "Siemens I-Surf card"
depends on ISA
help
This enables HiSax support for the Siemens I-Talk/I-Surf card with
ISAR chip.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_HSTSAPHIR
bool "HST Saphir card"
depends on ISA
help
This enables HiSax support for the HST Saphir card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_BKM_A4T
bool "Telekom A4T card"
depends on PCI
help
This enables HiSax support for the Telekom A4T card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_SCT_QUADRO
bool "Scitel Quadro card"
depends on PCI
help
This enables HiSax support for the Scitel Quadro card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_GAZEL
bool "Gazel cards"
help
This enables HiSax support for the Gazel cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_HFC_PCI
bool "HFC PCI-Bus cards"
depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
help
This enables HiSax support for the HFC-S PCI 2BDS0 based cards.
For more information see under
<file:Documentation/isdn/README.hfc-pci>.
config HISAX_W6692
bool "Winbond W6692 based cards"
depends on PCI
help
This enables HiSax support for Winbond W6692 based PCI ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
config HISAX_HFC_SX
bool "HFC-S+, HFC-SP, HFC-PCMCIA cards"
help
This enables HiSax support for the HFC-S+, HFC-SP and HFC-PCMCIA
cards. This code is not finished yet.
config HISAX_ENTERNOW_PCI
bool "Formula-n enter:now PCI card"
depends on HISAX_NETJET && PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
help
This enables HiSax support for the Formula-n enter:now PCI
ISDN card.
endif
if ISDN_DRV_HISAX
config HISAX_DEBUG
bool "HiSax debugging"
help
This enables debugging code in the new-style HiSax drivers, i.e.
the ST5481 USB driver currently.
If in doubt, say yes.
comment "HiSax PCMCIA card service modules"
config HISAX_SEDLBAUER_CS
tristate "Sedlbauer PCMCIA cards"
depends on PCMCIA && HISAX_SEDLBAUER
help
This enables the PCMCIA client driver for the Sedlbauer Speed Star
and Speed Star II cards.
config HISAX_ELSA_CS
tristate "ELSA PCMCIA MicroLink cards"
depends on PCMCIA && HISAX_ELSA
help
This enables the PCMCIA client driver for the Elsa PCMCIA MicroLink
card.
config HISAX_AVM_A1_CS
tristate "AVM A1 PCMCIA cards"
depends on PCMCIA && ISDN_DRV_HISAX
help
This enables the PCMCIA client driver for the AVM A1 / Fritz!Card
PCMCIA cards.
config HISAX_TELES_CS
tristate "TELES PCMCIA cards"
depends on PCMCIA && HISAX_16_3
help
This enables the PCMCIA client driver for the Teles PCMCIA cards.
comment "HiSax sub driver modules"
config HISAX_ST5481
tristate "ST5481 USB ISDN modem (EXPERIMENTAL)"
depends on USB && EXPERIMENTAL
select ISDN_HDLC
select CRC_CCITT
select BITREVERSE
help
This enables the driver for ST5481 based USB ISDN adapters,
e.g. the BeWan Gazel 128 USB
config HISAX_HFCUSB
tristate "HFC USB based ISDN modems (EXPERIMENTAL)"
depends on USB && EXPERIMENTAL
help
This enables the driver for HFC USB based ISDN modems.
config HISAX_HFC4S8S
tristate "HFC-4S/8S based ISDN cards (EXPERIMENTAL)"
depends on EXPERIMENTAL
help
This enables the driver for HFC-4S/8S based ISDN cards.
config HISAX_FRITZ_PCIPNP
tristate "AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)"
depends on PCI && EXPERIMENTAL
help
This enables the driver for the AVM Fritz!Card PCI,
Fritz!Card PCI v2 and Fritz!Card PnP.
(the latter also needs you to select "ISA Plug and Play support"
from the menu "Plug and Play configuration")
config HISAX_AVM_A1_PCMCIA
bool
depends on HISAX_AVM_A1_CS
default y
endif
endmenu