board-picotux200.c
/*
* linux/arch/arm/mach-at91/board-picotux200.c
*
* Copyright (C) 2005 SAN People
* Copyright (C) 2007 Kleinhenz Elektronik GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/mtd/physmap.h>
#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
#include <asm/arch/at91rm9200_mc.h>
#include "generic.h"
/*
* Serial port configuration.
* 0 .. 3 = USART0 .. USART3
* 4 = DBGU
*/
static struct at91_uart_config __initdata picotux200_uart_config = {
.console_tty = 0, /* ttyS0 */
.nr_tty = 2,
.tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
};
static void __init picotux200_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91rm9200_initialize(18432000, AT91RM9200_BGA);
/* Setup the serial ports and console */
at91_init_serial(&picotux200_uart_config);
}
static void __init picotux200_init_irq(void)
{
at91rm9200_init_interrupts(NULL);
}
static struct at91_eth_data __initdata picotux200_eth_data = {
.phy_irq_pin = AT91_PIN_PC4,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata picotux200_usbh_data = {
.ports = 1,
};
// static struct at91_udc_data __initdata picotux200_udc_data = {
// .vbus_pin = AT91_PIN_PD4,
// .pullup_pin = AT91_PIN_PD5,
// };
static struct at91_mmc_data __initdata picotux200_mmc_data = {
.det_pin = AT91_PIN_PB27,
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
};
// static struct spi_board_info picotux200_spi_devices[] = {
// { /* DataFlash chip */
// .modalias = "mtd_dataflash",
// .chip_select = 0,
// .max_speed_hz = 15 * 1000 * 1000,
// },
// #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
// { /* DataFlash card */
// .modalias = "mtd_dataflash",
// .chip_select = 3,
// .max_speed_hz = 15 * 1000 * 1000,
// },
// #endif
// };
#define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0
#define PICOTUX200_FLASH_SIZE 0x400000
static struct physmap_flash_data picotux200_flash_data = {
.width = 2,
};
static struct resource picotux200_flash_resource = {
.start = PICOTUX200_FLASH_BASE,
.end = PICOTUX200_FLASH_BASE + PICOTUX200_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device picotux200_flash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &picotux200_flash_data,
},
.resource = &picotux200_flash_resource,
.num_resources = 1,
};
static void __init picotux200_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&picotux200_eth_data);
/* USB Host */
at91_add_device_usbh(&picotux200_usbh_data);
/* USB Device */
// at91_add_device_udc(&picotux200_udc_data);
// at91_set_multi_drive(picotux200_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
/* I2C */
at91_add_device_i2c(NULL, 0);
/* SPI */
// at91_add_device_spi(picotux200_spi_devices, ARRAY_SIZE(picotux200_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
/* DataFlash card */
at91_set_gpio_output(AT91_PIN_PB22, 0);
#else
/* MMC */
at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
at91_add_device_mmc(0, &picotux200_mmc_data);
#endif
/* NOR Flash */
platform_device_register(&picotux200_flash);
}
MACHINE_START(PICOTUX2XX, "picotux 200")
/* Maintainer: Kleinhenz Elektronik GmbH */
.phys_io = AT91_BASE_SYS,
.io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
.boot_params = AT91_SDRAM_BASE + 0x100,
.timer = &at91rm9200_timer,
.map_io = picotux200_map_io,
.init_irq = picotux200_init_irq,
.init_machine = picotux200_board_init,
MACHINE_END