dma.h
#ifndef __ASM_ARM_DMA_H
#define __ASM_ARM_DMA_H
typedef unsigned int dmach_t;
#include <linux/spinlock.h>
#include <asm/system.h>
#include <asm/scatterlist.h>
#include <asm/arch/dma.h>
/*
* This is the maximum virtual address which can be DMA'd from.
*/
#ifndef MAX_DMA_ADDRESS
#define MAX_DMA_ADDRESS 0xffffffff
#endif
/*
* DMA modes
*/
typedef unsigned int dmamode_t;
#define DMA_MODE_MASK 3
#define DMA_MODE_READ 0
#define DMA_MODE_WRITE 1
#define DMA_MODE_CASCADE 2
#define DMA_AUTOINIT 4
extern spinlock_t dma_spin_lock;
static inline unsigned long claim_dma_lock(void)
{
unsigned long flags;
spin_lock_irqsave(&dma_spin_lock, flags);
return flags;
}
static inline void release_dma_lock(unsigned long flags)
{
spin_unlock_irqrestore(&dma_spin_lock, flags);
}
/* Clear the 'DMA Pointer Flip Flop'.
* Write 0 for LSB/MSB, 1 for MSB/LSB access.
*/
#define clear_dma_ff(channel)
/* Set only the page register bits of the transfer address.
*
* NOTE: This is an architecture specific function, and should
* be hidden from the drivers
*/
extern void set_dma_page(dmach_t channel, char pagenr);
/* Request a DMA channel
*
* Some architectures may need to do allocate an interrupt
*/
extern int request_dma(dmach_t channel, const char * device_id);
/* Free a DMA channel
*
* Some architectures may need to do free an interrupt
*/
extern void free_dma(dmach_t channel);
/* Enable DMA for this channel
*
* On some architectures, this may have other side effects like
* enabling an interrupt and setting the DMA registers.
*/
extern void enable_dma(dmach_t channel);
/* Disable DMA for this channel
*
* On some architectures, this may have other side effects like
* disabling an interrupt or whatever.
*/
extern void disable_dma(dmach_t channel);
/* Test whether the specified channel has an active DMA transfer
*/
extern int dma_channel_active(dmach_t channel);
/* Set the DMA scatter gather list for this channel
*
* This should not be called if a DMA channel is enabled,
* especially since some DMA architectures don't update the
* DMA address immediately, but defer it to the enable_dma().
*/
extern void set_dma_sg(dmach_t channel, struct scatterlist *sg, int nr_sg);
/* Set the DMA address for this channel
*
* This should not be called if a DMA channel is enabled,
* especially since some DMA architectures don't update the
* DMA address immediately, but defer it to the enable_dma().
*/
extern void __set_dma_addr(dmach_t channel, void *addr);
#define set_dma_addr(channel, addr) \
__set_dma_addr(channel, bus_to_virt(addr))
/* Set the DMA byte count for this channel
*
* This should not be called if a DMA channel is enabled,
* especially since some DMA architectures don't update the
* DMA count immediately, but defer it to the enable_dma().
*/
extern void set_dma_count(dmach_t channel, unsigned long count);
/* Set the transfer direction for this channel
*
* This should not be called if a DMA channel is enabled,
* especially since some DMA architectures don't update the
* DMA transfer direction immediately, but defer it to the
* enable_dma().
*/
extern void set_dma_mode(dmach_t channel, dmamode_t mode);
/* Set the transfer speed for this channel
*/
extern void set_dma_speed(dmach_t channel, int cycle_ns);
/* Get DMA residue count. After a DMA transfer, this
* should return zero. Reading this while a DMA transfer is
* still in progress will return unpredictable results.
* If called before the channel has been used, it may return 1.
* Otherwise, it returns the number of _bytes_ left to transfer.
*/
extern int get_dma_residue(dmach_t channel);
#ifndef NO_DMA
#define NO_DMA 255
#endif
#ifdef CONFIG_PCI
extern int isa_dma_bridge_buggy;
#else
#define isa_dma_bridge_buggy (0)
#endif
#endif /* _ARM_DMA_H */