panel-leadtek-ltk500hd1829.c
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (c) 2019 Theobroma Systems Design und Consulting GmbH
*
* base on panel-kingdisplay-kd097d04.c
* Copyright (c) 2017, Fuzhou Rockchip Electronics Co., Ltd
*/
#include <linux/backlight.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/regulator/consumer.h>
#include <video/mipi_display.h>
#include <drm/drm_crtc.h>
#include <drm/drm_device.h>
#include <drm/drm_mipi_dsi.h>
#include <drm/drm_modes.h>
#include <drm/drm_panel.h>
struct ltk500hd1829_cmd {
char cmd;
char data;
};
struct ltk500hd1829_desc {
const struct drm_display_mode *mode;
const struct ltk500hd1829_cmd *init;
unsigned int num_init;
};
struct ltk500hd1829 {
struct device *dev;
struct drm_panel panel;
struct gpio_desc *reset_gpio;
struct regulator *vcc;
struct regulator *iovcc;
const struct ltk500hd1829_desc *panel_desc;
bool prepared;
};
static const struct ltk500hd1829_cmd ltk101b4029w_init[] = {
/* Page0 */
{ 0xE0, 0x00 },
/* PASSWORD */
{ 0xE1, 0x93 },
{ 0xE2, 0x65 },
{ 0xE3, 0xF8 },
{ 0x80, 0x03 }, /* 0X03:4-LANE; 0X02:3-LANE; 0X01:2-LANE */
/* Page1 */
{ 0xE0, 0x01 },
/* Set VCOM */
{ 0x00, 0x00 },
{ 0x01, 0x6F },
/* Set Gamma Power, VGMP,VGMN,VGSP,VGSN */
{ 0x17, 0x00 },
{ 0x18, 0xAF }, /* 4.3V */
{ 0x19, 0x01 }, /* 0.3V */
{ 0x1A, 0x00 },
{ 0x1B, 0xAF }, /* 4.3V */
{ 0x1C, 0x01 }, /* 0.3V */
/* Set Gate Power */
{ 0x1F, 0x3E }, /* VGH_R = 15V */
{ 0x20, 0x28 }, /* VGL_R = -12V */
{ 0x21, 0x28 }, /* VGL_R2 = -12V */
{ 0x22, 0x7E },
/* SETPANEL */
{ 0x35, 0x26 },
{ 0x37, 0x09 },
/* SET RGBCYC */
{ 0x38, 0x04 },
{ 0x39, 0x00 },
{ 0x3A, 0x01 },
{ 0x3C, 0x7C },
{ 0x3D, 0xFF },
{ 0x3E, 0xFF },
{ 0x3F, 0x7F },
/* Set TCON */
{ 0x40, 0x06 }, /* RSO = 800 RGB */
{ 0x41, 0xA0 }, /* LN = 640->1280 line */
{ 0x42, 0x81 },
{ 0x43, 0x08 }, /* VFP = 8 */
{ 0x44, 0x0B }, /* VBP = 12 */
{ 0x45, 0x28 }, /* HBP = 40 */
/* power voltage */
{ 0x55, 0x0F }, /* DCDCM = 0001, JD PWR_IC */
{ 0x57, 0x69 },
{ 0x59, 0x0A }, /* VCL = -2.9V */
{ 0x5A, 0x28 }, /* VGH = 15V */
{ 0x5B, 0x14 }, /* VGL = -11V */
/* Gamma */
{ 0x5D, 0x7C },
{ 0x5E, 0x65 },
{ 0x5F, 0x55 },
{ 0x60, 0x47 },
{ 0x61, 0x43 },
{ 0x62, 0x32 },
{ 0x63, 0x34 },
{ 0x64, 0x1C },
{ 0x65, 0x33 },
{ 0x66, 0x31 },
{ 0x67, 0x30 },
{ 0x68, 0x4E },
{ 0x69, 0x3C },
{ 0x6A, 0x44 },
{ 0x6B, 0x35 },
{ 0x6C, 0x31 },
{ 0x6D, 0x23 },
{ 0x6E, 0x11 },
{ 0x6F, 0x00 },
{ 0x70, 0x7C },
{ 0x71, 0x65 },
{ 0x72, 0x55 },
{ 0x73, 0x47 },
{ 0x74, 0x43 },
{ 0x75, 0x32 },
{ 0x76, 0x34 },
{ 0x77, 0x1C },
{ 0x78, 0x33 },
{ 0x79, 0x31 },
{ 0x7A, 0x30 },
{ 0x7B, 0x4E },
{ 0x7C, 0x3C },
{ 0x7D, 0x44 },
{ 0x7E, 0x35 },
{ 0x7F, 0x31 },
{ 0x80, 0x23 },
{ 0x81, 0x11 },
{ 0x82, 0x00 },
/* Page2, for GIP */
{ 0xE0, 0x02 },
/* GIP_L Pin mapping */
{ 0x00, 0x1E },
{ 0x01, 0x1E },
{ 0x02, 0x41 },
{ 0x03, 0x41 },
{ 0x04, 0x43 },
{ 0x05, 0x43 },
{ 0x06, 0x1F },
{ 0x07, 0x1F },
{ 0x08, 0x35 },
{ 0x09, 0x1F },
{ 0x0A, 0x15 },
{ 0x0B, 0x15 },
{ 0x0C, 0x1F },
{ 0x0D, 0x47 },
{ 0x0E, 0x47 },
{ 0x0F, 0x45 },
{ 0x10, 0x45 },
{ 0x11, 0x4B },
{ 0x12, 0x4B },
{ 0x13, 0x49 },
{ 0x14, 0x49 },
{ 0x15, 0x1F },
/* GIP_R Pin mapping */
{ 0x16, 0x1E },
{ 0x17, 0x1E },
{ 0x18, 0x40 },
{ 0x19, 0x40 },
{ 0x1A, 0x42 },
{ 0x1B, 0x42 },
{ 0x1C, 0x1F },
{ 0x1D, 0x1F },
{ 0x1E, 0x35 },
{ 0x1F, 0x1F },
{ 0x20, 0x15 },
{ 0x21, 0x15 },
{ 0x22, 0x1f },
{ 0x23, 0x46 },
{ 0x24, 0x46 },
{ 0x25, 0x44 },
{ 0x26, 0x44 },
{ 0x27, 0x4A },
{ 0x28, 0x4A },
{ 0x29, 0x48 },
{ 0x2A, 0x48 },
{ 0x2B, 0x1F },
/* GIP Timing */
{ 0x58, 0x40 },
{ 0x5B, 0x30 },
{ 0x5C, 0x03 },
{ 0x5D, 0x30 },
{ 0x5E, 0x01 },
{ 0x5F, 0x02 },
{ 0x63, 0x14 },
{ 0x64, 0x6A },
{ 0x67, 0x73 },
{ 0x68, 0x05 },
{ 0x69, 0x14 },
{ 0x6A, 0x6A },
{ 0x6B, 0x08 },
{ 0x6C, 0x00 },
{ 0x6D, 0x00 },
{ 0x6E, 0x00 },
{ 0x6F, 0x88 },
{ 0x77, 0xDD },
{ 0x79, 0x0E },
{ 0x7A, 0x03 },
{ 0x7D, 0x14 },
{ 0x7E, 0x6A },
/* Page4 */
{ 0xE0, 0x04 },
{ 0x09, 0x11 },
{ 0x0E, 0x48 },
{ 0x2B, 0x2B },
{ 0x2D, 0x03 },
{ 0x2E, 0x44 },
/* Page0 */
{ 0xE0, 0x00 },
{ 0xE6, 0x02 },
{ 0xE7, 0x0C },
};
static const struct drm_display_mode ltk101b4029w_mode = {
.hdisplay = 800,
.hsync_start = 800 + 18,
.hsync_end = 800 + 18 + 18,
.htotal = 800 + 18 + 18 + 18,
.vdisplay = 1280,
.vsync_start = 1280 + 24,
.vsync_end = 1280 + 24 + 4,
.vtotal = 1280 + 24 + 4 + 8,
.clock = 67330,
.width_mm = 136,
.height_mm = 218,
};
static const struct ltk500hd1829_desc ltk101b4029w_data = {
.mode = <k101b4029w_mode,
.init = ltk101b4029w_init,
.num_init = ARRAY_SIZE(ltk101b4029w_init),
};
/*
* There is no description in the Reference Manual about these commands.
* We received them from the vendor, so just use them as is.
*/
static const struct ltk500hd1829_cmd ltk500hd1829_init[] = {
{ 0xE0, 0x00 },
{ 0xE1, 0x93 },
{ 0xE2, 0x65 },
{ 0xE3, 0xF8 },
{ 0x80, 0x03 },
{ 0xE0, 0x04 },
{ 0x2D, 0x03 },
{ 0xE0, 0x01 },
{ 0x00, 0x00 },
{ 0x01, 0xB6 },
{ 0x03, 0x00 },
{ 0x04, 0xC5 },
{ 0x17, 0x00 },
{ 0x18, 0xBF },
{ 0x19, 0x01 },
{ 0x1A, 0x00 },
{ 0x1B, 0xBF },
{ 0x1C, 0x01 },
{ 0x1F, 0x7C },
{ 0x20, 0x26 },
{ 0x21, 0x26 },
{ 0x22, 0x4E },
{ 0x37, 0x09 },
{ 0x38, 0x04 },
{ 0x39, 0x08 },
{ 0x3A, 0x1F },
{ 0x3B, 0x1F },
{ 0x3C, 0x78 },
{ 0x3D, 0xFF },
{ 0x3E, 0xFF },
{ 0x3F, 0x00 },
{ 0x40, 0x04 },
{ 0x41, 0xA0 },
{ 0x43, 0x0F },
{ 0x44, 0x0A },
{ 0x45, 0x24 },
{ 0x55, 0x01 },
{ 0x56, 0x01 },
{ 0x57, 0xA5 },
{ 0x58, 0x0A },
{ 0x59, 0x4A },
{ 0x5A, 0x38 },
{ 0x5B, 0x10 },
{ 0x5C, 0x19 },
{ 0x5D, 0x7C },
{ 0x5E, 0x64 },
{ 0x5F, 0x54 },
{ 0x60, 0x48 },
{ 0x61, 0x44 },
{ 0x62, 0x35 },
{ 0x63, 0x3A },
{ 0x64, 0x24 },
{ 0x65, 0x3B },
{ 0x66, 0x39 },
{ 0x67, 0x37 },
{ 0x68, 0x56 },
{ 0x69, 0x41 },
{ 0x6A, 0x47 },
{ 0x6B, 0x2F },
{ 0x6C, 0x23 },
{ 0x6D, 0x13 },
{ 0x6E, 0x02 },
{ 0x6F, 0x08 },
{ 0x70, 0x7C },
{ 0x71, 0x64 },
{ 0x72, 0x54 },
{ 0x73, 0x48 },
{ 0x74, 0x44 },
{ 0x75, 0x35 },
{ 0x76, 0x3A },
{ 0x77, 0x22 },
{ 0x78, 0x3B },
{ 0x79, 0x39 },
{ 0x7A, 0x38 },
{ 0x7B, 0x52 },
{ 0x7C, 0x41 },
{ 0x7D, 0x47 },
{ 0x7E, 0x2F },
{ 0x7F, 0x23 },
{ 0x80, 0x13 },
{ 0x81, 0x02 },
{ 0x82, 0x08 },
{ 0xE0, 0x02 },
{ 0x00, 0x57 },
{ 0x01, 0x77 },
{ 0x02, 0x44 },
{ 0x03, 0x46 },
{ 0x04, 0x48 },
{ 0x05, 0x4A },
{ 0x06, 0x4C },
{ 0x07, 0x4E },
{ 0x08, 0x50 },
{ 0x09, 0x55 },
{ 0x0A, 0x52 },
{ 0x0B, 0x55 },
{ 0x0C, 0x55 },
{ 0x0D, 0x55 },
{ 0x0E, 0x55 },
{ 0x0F, 0x55 },
{ 0x10, 0x55 },
{ 0x11, 0x55 },
{ 0x12, 0x55 },
{ 0x13, 0x40 },
{ 0x14, 0x55 },
{ 0x15, 0x55 },
{ 0x16, 0x57 },
{ 0x17, 0x77 },
{ 0x18, 0x45 },
{ 0x19, 0x47 },
{ 0x1A, 0x49 },
{ 0x1B, 0x4B },
{ 0x1C, 0x4D },
{ 0x1D, 0x4F },
{ 0x1E, 0x51 },
{ 0x1F, 0x55 },
{ 0x20, 0x53 },
{ 0x21, 0x55 },
{ 0x22, 0x55 },
{ 0x23, 0x55 },
{ 0x24, 0x55 },
{ 0x25, 0x55 },
{ 0x26, 0x55 },
{ 0x27, 0x55 },
{ 0x28, 0x55 },
{ 0x29, 0x41 },
{ 0x2A, 0x55 },
{ 0x2B, 0x55 },
{ 0x2C, 0x57 },
{ 0x2D, 0x77 },
{ 0x2E, 0x4F },
{ 0x2F, 0x4D },
{ 0x30, 0x4B },
{ 0x31, 0x49 },
{ 0x32, 0x47 },
{ 0x33, 0x45 },
{ 0x34, 0x41 },
{ 0x35, 0x55 },
{ 0x36, 0x53 },
{ 0x37, 0x55 },
{ 0x38, 0x55 },
{ 0x39, 0x55 },
{ 0x3A, 0x55 },
{ 0x3B, 0x55 },
{ 0x3C, 0x55 },
{ 0x3D, 0x55 },
{ 0x3E, 0x55 },
{ 0x3F, 0x51 },
{ 0x40, 0x55 },
{ 0x41, 0x55 },
{ 0x42, 0x57 },
{ 0x43, 0x77 },
{ 0x44, 0x4E },
{ 0x45, 0x4C },
{ 0x46, 0x4A },
{ 0x47, 0x48 },
{ 0x48, 0x46 },
{ 0x49, 0x44 },
{ 0x4A, 0x40 },
{ 0x4B, 0x55 },
{ 0x4C, 0x52 },
{ 0x4D, 0x55 },
{ 0x4E, 0x55 },
{ 0x4F, 0x55 },
{ 0x50, 0x55 },
{ 0x51, 0x55 },
{ 0x52, 0x55 },
{ 0x53, 0x55 },
{ 0x54, 0x55 },
{ 0x55, 0x50 },
{ 0x56, 0x55 },
{ 0x57, 0x55 },
{ 0x58, 0x40 },
{ 0x59, 0x00 },
{ 0x5A, 0x00 },
{ 0x5B, 0x10 },
{ 0x5C, 0x09 },
{ 0x5D, 0x30 },
{ 0x5E, 0x01 },
{ 0x5F, 0x02 },
{ 0x60, 0x30 },
{ 0x61, 0x03 },
{ 0x62, 0x04 },
{ 0x63, 0x06 },
{ 0x64, 0x6A },
{ 0x65, 0x75 },
{ 0x66, 0x0F },
{ 0x67, 0xB3 },
{ 0x68, 0x0B },
{ 0x69, 0x06 },
{ 0x6A, 0x6A },
{ 0x6B, 0x10 },
{ 0x6C, 0x00 },
{ 0x6D, 0x04 },
{ 0x6E, 0x04 },
{ 0x6F, 0x88 },
{ 0x70, 0x00 },
{ 0x71, 0x00 },
{ 0x72, 0x06 },
{ 0x73, 0x7B },
{ 0x74, 0x00 },
{ 0x75, 0xBC },
{ 0x76, 0x00 },
{ 0x77, 0x05 },
{ 0x78, 0x2E },
{ 0x79, 0x00 },
{ 0x7A, 0x00 },
{ 0x7B, 0x00 },
{ 0x7C, 0x00 },
{ 0x7D, 0x03 },
{ 0x7E, 0x7B },
{ 0xE0, 0x04 },
{ 0x09, 0x10 },
{ 0x2B, 0x2B },
{ 0x2E, 0x44 },
{ 0xE0, 0x00 },
{ 0xE6, 0x02 },
{ 0xE7, 0x02 },
{ 0x35, 0x00 },
};
static const struct drm_display_mode ltk500hd1829_mode = {
.hdisplay = 720,
.hsync_start = 720 + 50,
.hsync_end = 720 + 50 + 50,
.htotal = 720 + 50 + 50 + 50,
.vdisplay = 1280,
.vsync_start = 1280 + 30,
.vsync_end = 1280 + 30 + 4,
.vtotal = 1280 + 30 + 4 + 12,
.clock = 69217,
.width_mm = 62,
.height_mm = 110,
};
static const struct ltk500hd1829_desc ltk500hd1829_data = {
.mode = <k500hd1829_mode,
.init = ltk500hd1829_init,
.num_init = ARRAY_SIZE(ltk500hd1829_init),
};
static inline
struct ltk500hd1829 *panel_to_ltk500hd1829(struct drm_panel *panel)
{
return container_of(panel, struct ltk500hd1829, panel);
}
static int ltk500hd1829_unprepare(struct drm_panel *panel)
{
struct ltk500hd1829 *ctx = panel_to_ltk500hd1829(panel);
struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
int ret;
if (!ctx->prepared)
return 0;
ret = mipi_dsi_dcs_set_display_off(dsi);
if (ret < 0)
dev_err(panel->dev, "failed to set display off: %d\n", ret);
ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
if (ret < 0) {
dev_err(panel->dev, "failed to enter sleep mode: %d\n", ret);
}
/* 120ms to enter sleep mode */
msleep(120);
regulator_disable(ctx->iovcc);
regulator_disable(ctx->vcc);
ctx->prepared = false;
return 0;
}
static int ltk500hd1829_prepare(struct drm_panel *panel)
{
struct ltk500hd1829 *ctx = panel_to_ltk500hd1829(panel);
struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
unsigned int i;
int ret;
if (ctx->prepared)
return 0;
ret = regulator_enable(ctx->vcc);
if (ret < 0) {
dev_err(ctx->dev, "Failed to enable vci supply: %d\n", ret);
return ret;
}
ret = regulator_enable(ctx->iovcc);
if (ret < 0) {
dev_err(ctx->dev, "Failed to enable iovcc supply: %d\n", ret);
goto disable_vcc;
}
gpiod_set_value_cansleep(ctx->reset_gpio, 1);
/* tRW: 10us */
usleep_range(10, 20);
gpiod_set_value_cansleep(ctx->reset_gpio, 0);
/* tRT: >= 5ms */
usleep_range(5000, 6000);
for (i = 0; i < ctx->panel_desc->num_init; i++) {
ret = mipi_dsi_generic_write(dsi, &ctx->panel_desc->init[i],
sizeof(struct ltk500hd1829_cmd));
if (ret < 0) {
dev_err(panel->dev, "failed to write init cmds: %d\n", ret);
goto disable_iovcc;
}
}
ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
if (ret < 0) {
dev_err(panel->dev, "failed to exit sleep mode: %d\n", ret);
goto disable_iovcc;
}
/* 120ms to exit sleep mode */
msleep(120);
ret = mipi_dsi_dcs_set_display_on(dsi);
if (ret < 0) {
dev_err(panel->dev, "failed to set display on: %d\n", ret);
goto disable_iovcc;
}
ctx->prepared = true;
return 0;
disable_iovcc:
regulator_disable(ctx->iovcc);
disable_vcc:
regulator_disable(ctx->vcc);
return ret;
}
static int ltk500hd1829_get_modes(struct drm_panel *panel,
struct drm_connector *connector)
{
struct ltk500hd1829 *ctx = panel_to_ltk500hd1829(panel);
struct drm_display_mode *mode;
mode = drm_mode_duplicate(connector->dev, ctx->panel_desc->mode);
if (!mode) {
dev_err(ctx->dev, "failed to add mode %ux%u@%u\n",
ctx->panel_desc->mode->hdisplay, ctx->panel_desc->mode->vdisplay,
drm_mode_vrefresh(ctx->panel_desc->mode));
return -ENOMEM;
}
drm_mode_set_name(mode);
mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
connector->display_info.width_mm = mode->width_mm;
connector->display_info.height_mm = mode->height_mm;
drm_mode_probed_add(connector, mode);
return 1;
}
static const struct drm_panel_funcs ltk500hd1829_funcs = {
.unprepare = ltk500hd1829_unprepare,
.prepare = ltk500hd1829_prepare,
.get_modes = ltk500hd1829_get_modes,
};
static int ltk500hd1829_probe(struct mipi_dsi_device *dsi)
{
struct ltk500hd1829 *ctx;
struct device *dev = &dsi->dev;
int ret;
ctx = devm_kzalloc(&dsi->dev, sizeof(*ctx), GFP_KERNEL);
if (!ctx)
return -ENOMEM;
ctx->panel_desc = of_device_get_match_data(dev);
if (!ctx->panel_desc)
return -EINVAL;
ctx->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
if (IS_ERR(ctx->reset_gpio)) {
dev_err(dev, "cannot get reset gpio\n");
return PTR_ERR(ctx->reset_gpio);
}
ctx->vcc = devm_regulator_get(dev, "vcc");
if (IS_ERR(ctx->vcc)) {
ret = PTR_ERR(ctx->vcc);
if (ret != -EPROBE_DEFER)
dev_err(dev, "Failed to request vcc regulator: %d\n", ret);
return ret;
}
ctx->iovcc = devm_regulator_get(dev, "iovcc");
if (IS_ERR(ctx->iovcc)) {
ret = PTR_ERR(ctx->iovcc);
if (ret != -EPROBE_DEFER)
dev_err(dev, "Failed to request iovcc regulator: %d\n", ret);
return ret;
}
mipi_dsi_set_drvdata(dsi, ctx);
ctx->dev = dev;
dsi->lanes = 4;
dsi->format = MIPI_DSI_FMT_RGB888;
dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
drm_panel_init(&ctx->panel, &dsi->dev, <k500hd1829_funcs,
DRM_MODE_CONNECTOR_DSI);
ret = drm_panel_of_backlight(&ctx->panel);
if (ret)
return ret;
drm_panel_add(&ctx->panel);
ret = mipi_dsi_attach(dsi);
if (ret < 0) {
dev_err(dev, "mipi_dsi_attach failed: %d\n", ret);
drm_panel_remove(&ctx->panel);
return ret;
}
return 0;
}
static void ltk500hd1829_shutdown(struct mipi_dsi_device *dsi)
{
struct ltk500hd1829 *ctx = mipi_dsi_get_drvdata(dsi);
int ret;
ret = drm_panel_unprepare(&ctx->panel);
if (ret < 0)
dev_err(&dsi->dev, "Failed to unprepare panel: %d\n", ret);
ret = drm_panel_disable(&ctx->panel);
if (ret < 0)
dev_err(&dsi->dev, "Failed to disable panel: %d\n", ret);
}
static void ltk500hd1829_remove(struct mipi_dsi_device *dsi)
{
struct ltk500hd1829 *ctx = mipi_dsi_get_drvdata(dsi);
int ret;
ltk500hd1829_shutdown(dsi);
ret = mipi_dsi_detach(dsi);
if (ret < 0)
dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", ret);
drm_panel_remove(&ctx->panel);
}
static const struct of_device_id ltk500hd1829_of_match[] = {
{
.compatible = "leadtek,ltk101b4029w",
.data = <k101b4029w_data,
},
{
.compatible = "leadtek,ltk500hd1829",
.data = <k500hd1829_data,
},
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, ltk500hd1829_of_match);
static struct mipi_dsi_driver ltk500hd1829_driver = {
.driver = {
.name = "panel-leadtek-ltk500hd1829",
.of_match_table = ltk500hd1829_of_match,
},
.probe = ltk500hd1829_probe,
.remove = ltk500hd1829_remove,
.shutdown = ltk500hd1829_shutdown,
};
module_mipi_dsi_driver(ltk500hd1829_driver);
MODULE_AUTHOR("Heiko Stuebner <heiko.stuebner@theobroma-systems.com>");
MODULE_DESCRIPTION("Leadtek LTK500HD1829 panel driver");
MODULE_LICENSE("GPL v2");