qsemi.c
/*
* drivers/net/phy/qsemi.c
*
* Driver for Quality Semiconductor PHYs
*
* Author: Andy Fleming
*
* Copyright (c) 2004 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
*/
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <linux/unistd.h>
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
#include <linux/phy.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/uaccess.h>
/* ------------------------------------------------------------------------- */
/* The Quality Semiconductor QS6612 is used on the RPX CLLF */
/* register definitions */
#define MII_QS6612_MCR 17 /* Mode Control Register */
#define MII_QS6612_FTR 27 /* Factory Test Register */
#define MII_QS6612_MCO 28 /* Misc. Control Register */
#define MII_QS6612_ISR 29 /* Interrupt Source Register */
#define MII_QS6612_IMR 30 /* Interrupt Mask Register */
#define MII_QS6612_IMR_INIT 0x003a
#define MII_QS6612_PCR 31 /* 100BaseTx PHY Control Reg. */
#define QS6612_PCR_AN_COMPLETE 0x1000
#define QS6612_PCR_RLBEN 0x0200
#define QS6612_PCR_DCREN 0x0100
#define QS6612_PCR_4B5BEN 0x0040
#define QS6612_PCR_TX_ISOLATE 0x0020
#define QS6612_PCR_MLT3_DIS 0x0002
#define QS6612_PCR_SCRM_DESCRM 0x0001
MODULE_DESCRIPTION("Quality Semiconductor PHY driver");
MODULE_AUTHOR("Andy Fleming");
MODULE_LICENSE("GPL");
/* Returns 0, unless there's a write error */
static int qs6612_config_init(struct phy_device *phydev)
{
/* The PHY powers up isolated on the RPX,
* so send a command to allow operation.
* XXX - My docs indicate this should be 0x0940
* ...or something. The current value sets three
* reserved bits, bit 11, which specifies it should be
* set to one, bit 10, which specifies it should be set
* to 0, and bit 7, which doesn't specify. However, my
* docs are preliminary, and I will leave it like this
* until someone more knowledgable corrects me or it.
* -- Andy Fleming
*/
return phy_write(phydev, MII_QS6612_PCR, 0x0dc0);
}
static int qs6612_ack_interrupt(struct phy_device *phydev)
{
int err;
err = phy_read(phydev, MII_QS6612_ISR);
if (err < 0)
return err;
err = phy_read(phydev, MII_BMSR);
if (err < 0)
return err;
err = phy_read(phydev, MII_EXPANSION);
if (err < 0)
return err;
return 0;
}
static int qs6612_config_intr(struct phy_device *phydev)
{
int err;
if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
err = phy_write(phydev, MII_QS6612_IMR,
MII_QS6612_IMR_INIT);
else
err = phy_write(phydev, MII_QS6612_IMR, 0);
return err;
}
static struct phy_driver qs6612_driver[] = { {
.phy_id = 0x00181440,
.name = "QS6612",
.phy_id_mask = 0xfffffff0,
.features = PHY_BASIC_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_init = qs6612_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = qs6612_ack_interrupt,
.config_intr = qs6612_config_intr,
} };
module_phy_driver(qs6612_driver);
static struct mdio_device_id __maybe_unused qs6612_tbl[] = {
{ 0x00181440, 0xfffffff0 },
{ }
};
MODULE_DEVICE_TABLE(mdio, qs6612_tbl);