https://github.com/torvalds/linux
Tip revision: 521a547ced6477c54b4b0cc206000406c221b4d6 authored by Linus Torvalds on 18 September 2022, 20:44:14 UTC
Linux 6.0-rc6
Linux 6.0-rc6
Tip revision: 521a547
omap5-cm-t54.dts
// SPDX-License-Identifier: GPL-2.0
/*
* Support for CompuLab CM-T54
*/
/dts-v1/;
#include "omap5.dtsi"
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
model = "CompuLab CM-T54";
compatible = "compulab,omap5-cm-t54", "ti,omap5";
memory@80000000 {
device_type = "memory";
reg = <0 0x80000000 0 0x7f000000>; /* 2048 MB */
};
aliases {
display0 = &hdmi0;
display1 = &dvi0;
display2 = &lcd0;
};
vmmcsd_fixed: fixed-regulator-mmcsd {
compatible = "regulator-fixed";
regulator-name = "vmmcsd_fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vwlan_pdn_fixed: fixed-regulator-vwlan-pdn {
compatible = "regulator-fixed";
regulator-name = "vwlan_pdn_fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&ldo2_reg>;
gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* gpio4_109 */
startup-delay-us = <1000>;
enable-active-high;
};
vwlan_fixed: fixed-regulator-vwlan {
compatible = "regulator-fixed";
regulator-name = "vwlan_fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vwlan_pdn_fixed>;
gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* gpio4_110 */
startup-delay-us = <1000>;
enable-active-high;
};
ads7846reg: ads7846-reg {
compatible = "regulator-fixed";
regulator-name = "ads7846-reg";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
/* HS USB Host PHY on PORT 2 */
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
#phy-cells = <0>;
};
/* HS USB Host PHY on PORT 3 */
hsusb3_phy: hsusb3_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
#phy-cells = <0>;
};
leds {
compatible = "gpio-leds";
led1 {
label = "Heartbeat";
gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
linux,default-trigger = "heartbeat";
default-state = "off";
};
};
lcd0: display {
compatible = "startek,startek-kd050c", "panel-dpi";
label = "lcd";
pinctrl-names = "default";
pinctrl-0 = <&lcd_pins>;
enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
panel-timing {
clock-frequency = <33000000>;
hactive = <800>;
vactive = <480>;
hfront-porch = <40>;
hback-porch = <40>;
hsync-len = <43>;
vback-porch = <29>;
vfront-porch = <13>;
vsync-len = <3>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
port {
lcd_in: endpoint {
remote-endpoint = <&dpi_lcd_out>;
};
};
};
hdmi0: connector0 {
compatible = "hdmi-connector";
label = "hdmi";
type = "a";
pinctrl-names = "default";
pinctrl-0 = <&hdmi_conn_pins>;
hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
};
tfp410: encoder0 {
compatible = "ti,tfp410";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tfp410_in: endpoint {
remote-endpoint = <&dpi_dvi_out>;
};
};
port@1 {
reg = <1>;
tfp410_out: endpoint {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
dvi0: connector1 {
compatible = "dvi-connector";
label = "dvi";
digital;
ddc-i2c-bus = <&i2c2>;
port {
dvi_connector_in: endpoint {
remote-endpoint = <&tfp410_out>;
};
};
};
};
&omap5_pmx_wkup {
ads7846_pins: pinmux_ads7846_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0042, PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */
>;
};
palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
pinctrl-single,pins = <
/* sys_nirq1 is pulled down as the SoC is inverting it for GIC */
OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0)
>;
};
};
&omap5_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&led_gpio_pins
&usbhost_pins
>;
led_gpio_pins: pinmux_led_gpio_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
>;
};
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
>;
};
i2c2_pins: pinmux_i2c2_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
>;
};
mmc1_pins: pinmux_mmc1_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
>;
};
mmc2_pins: pinmux_mmc2_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
>;
};
mmc3_pins: pinmux_mmc3_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
>;
};
wlan_gpios_pins: pinmux_wlan_gpios_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */
OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */
>;
};
usbhost_pins: pinmux_usbhost_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
>;
};
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */
OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
>;
};
lcd_pins: pinmux_lcd_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */
>;
};
hdmi_conn_pins: pinmux_hdmi_conn_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
>;
};
dss_dpi_pins: pinmux_dss_dpi_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */
OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */
OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */
OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */
OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */
OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */
OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */
OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */
OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */
OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */
OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */
OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */
OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */
OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */
OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */
OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */
OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */
OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */
OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */
OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */
OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */
OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */
OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */
OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */
OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */
OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */
OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */
OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */
>;
};
mcspi2_pins: pinmux_mcspi1_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */
OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */
>;
};
};
&mcspi2 {
pinctrl-names = "default";
pinctrl-0 = <&mcspi2_pins>;
/* touch controller */
ads7846@0 {
pinctrl-names = "default";
pinctrl-0 = <&ads7846_pins>;
compatible = "ti,ads7846";
vcc-supply = <&ads7846reg>;
reg = <0>; /* CS0 */
spi-max-frequency = <1500000>;
interrupt-parent = <&gpio1>;
interrupts = <15 0>; /* gpio1_wk15 */
pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
ti,x-min = /bits/ 16 <0x0>;
ti,x-max = /bits/ 16 <0x0fff>;
ti,y-min = /bits/ 16 <0x0>;
ti,y-max = /bits/ 16 <0x0fff>;
ti,x-plate-ohms = /bits/ 16 <180>;
ti,pressure-max = /bits/ 16 <255>;
ti,debounce-max = /bits/ 16 <30>;
ti,debounce-tol = /bits/ 16 <10>;
ti,debounce-rep = /bits/ 16 <1>;
wakeup-source;
};
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <&ldo9_reg>;
bus-width = <4>;
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&vmmcsd_fixed>;
bus-width = <8>;
ti,non-removable;
};
&mmc3 {
pinctrl-names = "default";
pinctrl-0 = <
&mmc3_pins
&wlan_gpios_pins
>;
vmmc-supply = <&vwlan_fixed>;
bus-width = <4>;
ti,non-removable;
};
&mmc4 {
status = "disabled";
};
&mmc5 {
status = "disabled";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
at24@50 {
compatible = "atmel,24c02";
pagesize = <16>;
reg = <0x50>;
};
palmas: palmas@48 {
compatible = "ti,palmas";
reg = <0x48>;
pinctrl-0 = <&palmas_sys_nirq_pins>;
pinctrl-names = "default";
/* sys_nirq/ext_sys_irq pins get inverted at mpuss wakeupgen */
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <2>;
ti,system-power-controller;
extcon_usb3: palmas_usb {
compatible = "ti,palmas-usb-vid";
ti,enable-vbus-detection;
ti,enable-id-detection;
ti,wakeup;
};
rtc {
compatible = "ti,palmas-rtc";
interrupt-parent = <&palmas>;
interrupts = <8 IRQ_TYPE_NONE>;
};
palmas_pmic {
compatible = "ti,palmas-pmic";
interrupt-parent = <&palmas>;
interrupts = <14 IRQ_TYPE_NONE>;
interrupt-names = "short-irq";
ti,ldo6-vibrator;
regulators {
smps123_reg: smps123 {
/* VDD_OPP_MPU */
regulator-name = "smps123";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
};
smps45_reg: smps45 {
/* VDD_OPP_MM */
regulator-name = "smps45";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1310000>;
regulator-always-on;
regulator-boot-on;
};
smps6_reg: smps6 {
/* VDD_DDR3 - over VDD_SMPS6 */
regulator-name = "smps6";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
};
smps7_reg: smps7 {
/* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
regulator-name = "smps7";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
smps8_reg: smps8 {
/* VDD_OPP_CORE */
regulator-name = "smps8";
regulator-min-microvolt = < 600000>;
regulator-max-microvolt = <1310000>;
regulator-always-on;
regulator-boot-on;
};
smps9_reg: smps9 {
/* VDDA_2v1_AUD over VDD_2v1 */
regulator-name = "smps9";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
ti,smps-range = <0x80>;
regulator-always-on;
regulator-boot-on;
};
smps10_out2_reg: smps10_out2 {
/* VBUS_5V_OTG */
regulator-name = "smps10_out2";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
regulator-boot-on;
};
smps10_out1_reg: smps10_out1 {
/* VBUS_5V_OTG */
regulator-name = "smps10_out1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
ldo1_reg: ldo1 {
/* VDDAPHY_CAM: vdda_csiport */
regulator-name = "ldo1";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
ldo2_reg: ldo2 {
/* VDD_3V3_WLAN */
regulator-name = "ldo2";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <1000>;
};
ldo3_reg: ldo3 {
/* VCC_1V5_AUD */
regulator-name = "ldo3";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
regulator-boot-on;
};
ldo4_reg: ldo4 {
/* VDDAPHY_DISP: vdda_dsiport/hdmi */
regulator-name = "ldo4";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
ldo5_reg: ldo5 {
/* VDDA_1V8_PHY: usb/sata/hdmi.. */
regulator-name = "ldo5";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldo6_reg: ldo6 {
/* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
regulator-name = "ldo6";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
};
ldo7_reg: ldo7 {
/* VDD_VPP: vpp1 */
regulator-name = "ldo7";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
/* Only for efuse reprograming! */
status = "disabled";
};
ldo8_reg: ldo8 {
/* VDD_3V_GP: act led/serial console */
regulator-name = "ldo8";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
regulator-boot-on;
};
ldo9_reg: ldo9 {
/* VCC_DV_SDIO: vdds_sdcard */
regulator-name = "ldo9";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3000000>;
regulator-boot-on;
};
ldoln_reg: ldoln {
/* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
regulator-name = "ldoln";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldousb_reg: ldousb {
/* VDDA_3V_USB: VDDA_USBHS33 */
regulator-name = "ldousb";
regulator-min-microvolt = <3250000>;
regulator-max-microvolt = <3250000>;
regulator-always-on;
regulator-boot-on;
};
regen3_reg: regen3 {
/* REGEN3 controls LDO9 supply to card */
regulator-name = "regen3";
regulator-always-on;
regulator-boot-on;
};
};
};
};
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
clock-frequency = <100000>;
};
&usbhshost {
port2-mode = "ehci-hsic";
port3-mode = "ehci-hsic";
};
&usbhsehci {
phys = <0 &hsusb2_phy &hsusb3_phy>;
};
&usb3 {
extcon = <&extcon_usb3>;
vbus-supply = <&smps10_out1_reg>;
};
&cpu0 {
cpu0-supply = <&smps123_reg>;
};
&dss {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
port {
#address-cells = <1>;
#size-cells = <0>;
dpi_dvi_out: endpoint@0 {
reg = <0>;
remote-endpoint = <&tfp410_in>;
data-lines = <24>;
};
dpi_lcd_out: endpoint@1 {
reg = <1>;
remote-endpoint = <&lcd_in>;
data-lines = <24>;
};
};
};
&dsi2 {
status = "okay";
vdd-supply = <&ldo4_reg>;
};
&hdmi {
status = "okay";
vdda-supply = <&ldo4_reg>;
pinctrl-names = "default";
pinctrl-0 = <&dss_hdmi_pins>;
port {
hdmi_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
lanes = <1 0 3 2 5 4 7 6>;
};
};
};