https://github.com/torvalds/linux
Tip revision: ddf28352b80c86754a6424e3a61e8bdf9213b3c7 authored by Linus Torvalds on 04 September 2011, 22:45:10 UTC
Linux 3.1-rc5
Linux 3.1-rc5
Tip revision: ddf2835
Kconfig
config M68K
bool
default y
select HAVE_IDE
select HAVE_AOUT if MMU
select GENERIC_ATOMIC64 if MMU
select HAVE_GENERIC_HARDIRQS if !MMU
select GENERIC_IRQ_SHOW if !MMU
select ARCH_HAVE_NMI_SAFE_CMPXCHG if RMW_INSNS
config RWSEM_GENERIC_SPINLOCK
bool
default y
config RWSEM_XCHGADD_ALGORITHM
bool
config ARCH_HAS_ILOG2_U32
bool
config ARCH_HAS_ILOG2_U64
bool
config GENERIC_HWEIGHT
bool
default y
config GENERIC_CALIBRATE_DELAY
bool
default y
config TIME_LOW_RES
bool
default y
config NO_IOPORT
def_bool y
config NO_DMA
def_bool (MMU && SUN3) || (!MMU && !COLDFIRE)
config ZONE_DMA
bool
default y
config CPU_HAS_NO_BITFIELDS
bool
config HZ
int
default 1000 if CLEOPATRA
default 100
source "init/Kconfig"
source "kernel/Kconfig.freezer"
config MMU
bool "MMU-based Paged Memory Management Support"
default y
help
Select if you want MMU-based virtualised addressing space
support by paged memory management. If unsure, say 'Y'.
menu "Platform dependent setup"
if MMU
source arch/m68k/Kconfig.mmu
endif
if !MMU
source arch/m68k/Kconfig.nommu
endif
source "mm/Kconfig"
endmenu
menu "Executable file formats"
source "fs/Kconfig.binfmt"
endmenu
if !MMU
menu "Power management options"
config PM
bool "Power Management support"
help
Support processor power management modes
endmenu
endif
source "net/Kconfig"
source "drivers/Kconfig"
if MMU
menu "Character devices"
config ATARI_MFPSER
tristate "Atari MFP serial support"
depends on ATARI
---help---
If you like to use the MFP serial ports ("Modem1", "Serial1") under
Linux, say Y. The driver equally supports all kinds of MFP serial
ports and automatically detects whether Serial1 is available.
To compile this driver as a module, choose M here.
Note for Falcon users: You also have an MFP port, it's just not
wired to the outside... But you could use the port under Linux.
config ATARI_MIDI
tristate "Atari MIDI serial support"
depends on ATARI
help
If you want to use your Atari's MIDI port in Linux, say Y.
To compile this driver as a module, choose M here.
config ATARI_DSP56K
tristate "Atari DSP56k support (EXPERIMENTAL)"
depends on ATARI && EXPERIMENTAL
help
If you want to be able to use the DSP56001 in Falcons, say Y. This
driver is still experimental, and if you don't know what it is, or
if you don't have this processor, just say N.
To compile this driver as a module, choose M here.
config AMIGA_BUILTIN_SERIAL
tristate "Amiga builtin serial support"
depends on AMIGA
help
If you want to use your Amiga's built-in serial port in Linux,
answer Y.
To compile this driver as a module, choose M here.
config MULTIFACE_III_TTY
tristate "Multiface Card III serial support"
depends on AMIGA
help
If you want to use a Multiface III card's serial port in Linux,
answer Y.
To compile this driver as a module, choose M here.
config GVPIOEXT
tristate "GVP IO-Extender support"
depends on PARPORT=n && ZORRO
help
If you want to use a GVP IO-Extender serial card in Linux, say Y.
Otherwise, say N.
config GVPIOEXT_LP
tristate "GVP IO-Extender parallel printer support"
depends on GVPIOEXT
help
Say Y to enable driving a printer from the parallel port on your
GVP IO-Extender card, N otherwise.
config GVPIOEXT_PLIP
tristate "GVP IO-Extender PLIP support"
depends on GVPIOEXT
help
Say Y to enable doing IP over the parallel port on your GVP
IO-Extender card, N otherwise.
config MAC_HID
bool
depends on INPUT_ADBHID
default y
config HPDCA
tristate "HP DCA serial support"
depends on DIO && SERIAL_8250
help
If you want to use the internal "DCA" serial ports on an HP300
machine, say Y here.
config HPAPCI
tristate "HP APCI serial support"
depends on HP300 && SERIAL_8250 && EXPERIMENTAL
help
If you want to use the internal "APCI" serial ports on an HP400
machine, say Y here.
config MVME147_SCC
bool "SCC support for MVME147 serial ports"
depends on MVME147 && BROKEN
help
This is the driver for the serial ports on the Motorola MVME147
boards. Everyone using one of these boards should say Y here.
config MVME162_SCC
bool "SCC support for MVME162 serial ports"
depends on MVME16x && BROKEN
help
This is the driver for the serial ports on the Motorola MVME162 and
172 boards. Everyone using one of these boards should say Y here.
config BVME6000_SCC
bool "SCC support for BVME6000 serial ports"
depends on BVME6000 && BROKEN
help
This is the driver for the serial ports on the BVME4000 and BVME6000
boards from BVM Ltd. Everyone using one of these boards should say
Y here.
config DN_SERIAL
bool "Support for DN serial port (dummy)"
depends on APOLLO
config SERIAL_CONSOLE
bool "Support for serial port console"
depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
kernel messages and warnings and which allows logins in single user
mode). This could be useful if some terminal or printer is connected
to that serial port.
Even if you say Y here, the currently visible virtual console
(/dev/tty0) will still be used as the system console by default, but
you can alter that using a kernel command line option such as
"console=ttyS1". (Try "man bootparam" or see the documentation of
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
If you don't have a VGA card installed and you say Y here, the
kernel will automatically use the first serial line, /dev/ttyS0, as
system console.
If unsure, say N.
endmenu
endif
source "fs/Kconfig"
source "arch/m68k/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"