https://github.com/torvalds/linux
Tip revision: 6613476e225e090cc9aad49be7fa504e290dd33d authored by Linus Torvalds on 21 January 2024, 22:11:32 UTC
Linux 6.8-rc1
Linux 6.8-rc1
Tip revision: 6613476
i2c-iop3xx.h
/* SPDX-License-Identifier: GPL-2.0-only */
/* ------------------------------------------------------------------------- */
/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c */
/* ------------------------------------------------------------------------- */
/* Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd
* <Peter dot Milne at D hyphen TACQ dot com>
*/
/* ------------------------------------------------------------------------- */
#ifndef I2C_IOP3XX_H
#define I2C_IOP3XX_H 1
/*
* iop321 hardware bit definitions
*/
#define IOP3XX_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */
#define IOP3XX_ICR_UNIT_RESET 0x4000 /* 1=RESET */
#define IOP3XX_ICR_SAD_IE 0x2000 /* 1=Slave Detect Interrupt Enable */
#define IOP3XX_ICR_ALD_IE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */
#define IOP3XX_ICR_SSD_IE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */
#define IOP3XX_ICR_BERR_IE 0x0400 /* 1=Bus Error Interrupt Enable */
#define IOP3XX_ICR_RXFULL_IE 0x0200 /* 1=Receive Full Interrupt Enable */
#define IOP3XX_ICR_TXEMPTY_IE 0x0100 /* 1=Transmit Empty Interrupt Enable */
#define IOP3XX_ICR_GCD 0x0080 /* 1=General Call Disable */
/*
* IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set
* when sending a master mode general call message from the I2C unit"
*/
#define IOP3XX_ICR_UE 0x0040 /* 1=Unit Enable */
/*
* "NOTE: To avoid I2C bus integrity problems,
* the user needs to ensure that the GPIO Output Data Register -
* GPOD bits associated with an I2C port are cleared prior to setting
* the enable bit for that I2C serial port.
* The user prepares to enable I2C port 0 and
* I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively.
*/
#define IOP3XX_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */
#define IOP3XX_ICR_MABORT 0x0010 /* 1=Send a STOP with no data
* NB TBYTE must be clear */
#define IOP3XX_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */
#define IOP3XX_ICR_NACK 0x0004 /* 1=reply with NACK */
#define IOP3XX_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */
#define IOP3XX_ICR_MSTART 0x0001 /* 1=initiate a START */
#define IOP3XX_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */
#define IOP3XX_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */
#define IOP3XX_ISR_GCAD 0x0100 /* 1=General Call Address Detected */
#define IOP3XX_ISR_RXFULL 0x0080 /* 1=Receive Full */
#define IOP3XX_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */
#define IOP3XX_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */
#define IOP3XX_ISR_SSD 0x0010 /* 1=Slave STOP Detected */
#define IOP3XX_ISR_BBUSY 0x0008 /* 1=Bus BUSY */
#define IOP3XX_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */
#define IOP3XX_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */
#define IOP3XX_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */
#define IOP3XX_ISR_CLEARBITS 0x07f0
#define IOP3XX_ISAR_SAMASK 0x007f
#define IOP3XX_IDBR_MASK 0x00ff
#define IOP3XX_IBMR_SCL 0x0002
#define IOP3XX_IBMR_SDA 0x0001
#define IOP3XX_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */
#define IOP3XX_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */
#define MYSAR 0 /* default slave address */
#define I2C_ERR 321
#define I2C_ERR_BERR (I2C_ERR+0)
#define I2C_ERR_ALD (I2C_ERR+1)
#define CR_OFFSET 0
#define SR_OFFSET 0x4
#define SAR_OFFSET 0x8
#define DBR_OFFSET 0xc
#define CCR_OFFSET 0x10
#define BMR_OFFSET 0x14
#define IOP3XX_I2C_IO_SIZE 0x18
struct i2c_algo_iop3xx_data {
void __iomem *ioaddr;
wait_queue_head_t waitq;
spinlock_t lock;
u32 SR_enabled, SR_received;
int id;
struct gpio_desc *gpio_scl;
struct gpio_desc *gpio_sda;
};
#endif /* I2C_IOP3XX_H */