https://jxself.org/git/linux-libre.git
Tip revision: 6af9f081f00b81839003e7a4ff9f29ad80a97940 authored by Jason Self on 03 November 2013, 23:41:59 UTC
Linux-libre 3.12-gnu
Linux-libre 3.12-gnu
Tip revision: 6af9f08
README.i2400m
Driver for the Intel Wireless Wimax Connection 2400m
(C) 2008 Intel Corporation < linux-wimax@intel.com >
This provides a driver for the Intel Wireless WiMAX Connection 2400m
and a basic Linux kernel WiMAX stack.
1. Requirements
* Linux installation with Linux kernel 2.6.22 or newer (if building
from a separate tree)
* Intel i2400m Echo Peak or Baxter Peak; this includes the Intel
Wireless WiMAX/WiFi Link 5x50 series.
* build tools:
+ Linux kernel development package for the target kernel; to
build against your currently running kernel, you need to have
the kernel development package corresponding to the running
image installed (usually if your kernel is named
linux-VERSION, the development package is called
linux-dev-VERSION or linux-headers-VERSION).
+ GNU C Compiler, make
2. Compilation and installation
2.1. Compilation of the drivers included in the kernel
Configure the kernel; to enable the WiMAX drivers select Drivers >
Networking Drivers > WiMAX device support. Enable all of them as
modules (easier).
If USB or SDIO are not enabled in the kernel configuration, the options
to build the i2400m USB or SDIO drivers will not show. Enable said
subsystems and go back to the WiMAX menu to enable the drivers.
Compile and install your kernel as usual.
2.2. Compilation of the drivers distributed as an standalone module
To compile
$ cd source/directory
$ make
Once built you can load and unload using the provided load.sh script;
load.sh will load the modules, load.sh u will unload them.
To install in the default kernel directories (and enable auto loading
when the device is plugged):
$ make install
$ depmod -a
If your kernel development files are located in a non standard
directory or if you want to build for a kernel that is not the
currently running one, set KDIR to the right location:
$ make KDIR=/path/to/kernel/dev/tree
For more information, please contact linux-wimax@intel.com.
/*(DEBLOBBED)*/
4. Design
This package contains two major parts: a WiMAX kernel stack and a
driver for the Intel i2400m.
The WiMAX stack is designed to provide for common WiMAX control
services to current and future WiMAX devices from any vendor; please
see README.wimax for details.
The i2400m kernel driver is broken up in two main parts: the bus
generic driver and the bus-specific drivers. The bus generic driver
forms the drivercore and contain no knowledge of the actual method we
use to connect to the device. The bus specific drivers are just the
glue to connect the bus-generic driver and the device. Currently only
USB and SDIO are supported. See drivers/net/wimax/i2400m/i2400m.h for
more information.
The bus generic driver is logically broken up in two parts: OS-glue and
hardware-glue. The OS-glue interfaces with Linux. The hardware-glue
interfaces with the device on using an interface provided by the
bus-specific driver. The reason for this breakup is to be able to
easily reuse the hardware-glue to write drivers for other OSes; note
the hardware glue part is written as a native Linux driver; no
abstraction layers are used, so to port to another OS, the Linux kernel
API calls should be replaced with the target OS's.
5. Usage
To load the driver, follow the instructions in the install section;
once the driver is loaded, plug in the device (unless it is permanently
plugged in). The driver will enumerate the device, upload the firmware
and output messages in the kernel log (dmesg, /var/log/messages or
/var/log/kern.log) such as:
...
i2400m_usb 5-4:1.0: firmware interface version 8.0.0
i2400m_usb 5-4:1.0: WiMAX interface wmx0 (00:1d:e1:01:94:2c) ready
At this point the device is ready to work.
Current versions require the Intel WiMAX Network Service in userspace
to make things work. See the network service's README for instructions
on how to scan, connect and disconnect.
5.1. Module parameters
Module parameters can be set at kernel or module load time or by
echoing values:
$ echo VALUE > /sys/module/MODULENAME/parameters/PARAMETERNAME
To make changes permanent, for example, for the i2400m module, you can
also create a file named /etc/modprobe.d/i2400m containing:
options i2400m idle_mode_disabled=1
To find which parameters are supported by a module, run:
$ modinfo path/to/module.ko
During kernel bootup (if the driver is linked in the kernel), specify
the following to the kernel command line:
i2400m.PARAMETER=VALUE
5.1.1. i2400m: idle_mode_disabled
The i2400m module supports a parameter to disable idle mode. This
parameter, once set, will take effect only when the device is
reinitialized by the driver (eg: following a reset or a reconnect).
5.2. Debug operations: debugfs entries
The driver will register debugfs entries that allow the user to tweak
debug settings. There are three main container directories where
entries are placed, which correspond to the three blocks a i2400m WiMAX
driver has:
* /sys/kernel/debug/wimax:DEVNAME/ for the generic WiMAX stack
controls
* /sys/kernel/debug/wimax:DEVNAME/i2400m for the i2400m generic
driver controls
* /sys/kernel/debug/wimax:DEVNAME/i2400m-usb (or -sdio) for the
bus-specific i2400m-usb or i2400m-sdio controls).
Of course, if debugfs is mounted in a directory other than
/sys/kernel/debug, those paths will change.
5.2.1. Increasing debug output
The files named *dl_* indicate knobs for controlling the debug output
of different submodules:
*
# find /sys/kernel/debug/wimax\:wmx0 -name \*dl_\*
/sys/kernel/debug/wimax:wmx0/i2400m-usb/dl_tx
/sys/kernel/debug/wimax:wmx0/i2400m-usb/dl_rx
/sys/kernel/debug/wimax:wmx0/i2400m-usb/dl_notif
/sys/kernel/debug/wimax:wmx0/i2400m-usb/dl_fw
/sys/kernel/debug/wimax:wmx0/i2400m-usb/dl_usb
/sys/kernel/debug/wimax:wmx0/i2400m/dl_tx
/sys/kernel/debug/wimax:wmx0/i2400m/dl_rx
/sys/kernel/debug/wimax:wmx0/i2400m/dl_rfkill
/sys/kernel/debug/wimax:wmx0/i2400m/dl_netdev
/sys/kernel/debug/wimax:wmx0/i2400m/dl_fw
/sys/kernel/debug/wimax:wmx0/i2400m/dl_debugfs
/sys/kernel/debug/wimax:wmx0/i2400m/dl_driver
/sys/kernel/debug/wimax:wmx0/i2400m/dl_control
/sys/kernel/debug/wimax:wmx0/wimax_dl_stack
/sys/kernel/debug/wimax:wmx0/wimax_dl_op_rfkill
/sys/kernel/debug/wimax:wmx0/wimax_dl_op_reset
/sys/kernel/debug/wimax:wmx0/wimax_dl_op_msg
/sys/kernel/debug/wimax:wmx0/wimax_dl_id_table
/sys/kernel/debug/wimax:wmx0/wimax_dl_debugfs
By reading the file you can obtain the current value of said debug
level; by writing to it, you can set it.
To increase the debug level of, for example, the i2400m's generic TX
engine, just write:
$ echo 3 > /sys/kernel/debug/wimax:wmx0/i2400m/dl_tx
Increasing numbers yield increasing debug information; for details of
what is printed and the available levels, check the source. The code
uses 0 for disabled and increasing values until 8.
5.2.2. RX and TX statistics
The i2400m/rx_stats and i2400m/tx_stats provide statistics about the
data reception/delivery from the device:
$ cat /sys/kernel/debug/wimax:wmx0/i2400m/rx_stats
45 1 3 34 3104 48 480
The numbers reported are
* packets/RX-buffer: total, min, max
* RX-buffers: total RX buffers received, accumulated RX buffer size
in bytes, min size received, max size received
Thus, to find the average buffer size received, divide accumulated
RX-buffer / total RX-buffers.
To clear the statistics back to 0, write anything to the rx_stats file:
$ echo 1 > /sys/kernel/debug/wimax:wmx0/i2400m_rx_stats
Likewise for TX.
Note the packets this debug file refers to are not network packet, but
packets in the sense of the device-specific protocol for communication
to the host. See drivers/net/wimax/i2400m/tx.c.
5.2.3. Tracing messages received from user space
To echo messages received from user space into the trace pipe that the
i2400m driver creates, set the debug file i2400m/trace_msg_from_user to
1:
*
$ echo 1 > /sys/kernel/debug/wimax:wmx0/i2400m/trace_msg_from_user
5.2.4. Performing a device reset
By writing a 0, a 1 or a 2 to the file
/sys/kernel/debug/wimax:wmx0/reset, the driver performs a warm (without
disconnecting from the bus), cold (disconnecting from the bus) or bus
(bus specific) reset on the device.
5.2.5. Asking the device to enter power saving mode
By writing any value to the /sys/kernel/debug/wimax:wmx0 file, the
device will attempt to enter power saving mode.
6. Troubleshooting
/*(DEBLOBBED)*/