https://jxself.org/git/linux-libre.git
Tip revision: e8eb34aadc074ba9276a085e333d39a5d06313d3 authored by Jason Self on 02 July 2009, 23:52:50 UTC
Linux-libre 2.6.30.1-gnu1
Linux-libre 2.6.30.1-gnu1
Tip revision: e8eb34a
de600.h
/**************************************************
* *
* Definition of D-Link Ethernet Pocket adapter *
* *
**************************************************/
/*
* D-Link Ethernet pocket adapter ports
*/
/*
* OK, so I'm cheating, but there are an awful lot of
* reads and writes in order to get anything in and out
* of the DE-600 with 4 bits at a time in the parallel port,
* so every saved instruction really helps :-)
*/
#ifndef DE600_IO
#define DE600_IO 0x378
#endif
#define DATA_PORT (DE600_IO)
#define STATUS_PORT (DE600_IO + 1)
#define COMMAND_PORT (DE600_IO + 2)
#ifndef DE600_IRQ
#define DE600_IRQ 7
#endif
/*
* It really should look like this, and autoprobing as well...
*
#define DATA_PORT (dev->base_addr + 0)
#define STATUS_PORT (dev->base_addr + 1)
#define COMMAND_PORT (dev->base_addr + 2)
#define DE600_IRQ dev->irq
*/
/*
* D-Link COMMAND_PORT commands
*/
#define SELECT_NIC 0x04 /* select Network Interface Card */
#define SELECT_PRN 0x1c /* select Printer */
#define NML_PRN 0xec /* normal Printer situation */
#define IRQEN 0x10 /* enable IRQ line */
/*
* D-Link STATUS_PORT
*/
#define RX_BUSY 0x80
#define RX_GOOD 0x40
#define TX_FAILED16 0x10
#define TX_BUSY 0x08
/*
* D-Link DATA_PORT commands
* command in low 4 bits
* data in high 4 bits
* select current data nibble with HI_NIBBLE bit
*/
#define WRITE_DATA 0x00 /* write memory */
#define READ_DATA 0x01 /* read memory */
#define STATUS 0x02 /* read status register */
#define COMMAND 0x03 /* write command register (see COMMAND below) */
#define NULL_COMMAND 0x04 /* null command */
#define RX_LEN 0x05 /* read received packet length */
#define TX_ADDR 0x06 /* set adapter transmit memory address */
#define RW_ADDR 0x07 /* set adapter read/write memory address */
#define HI_NIBBLE 0x08 /* read/write the high nibble of data,
or-ed with rest of command */
/*
* command register, accessed through DATA_PORT with low bits = COMMAND
*/
#define RX_ALL 0x01 /* PROMISCUOUS */
#define RX_BP 0x02 /* default: BROADCAST & PHYSICAL ADDRESS */
#define RX_MBP 0x03 /* MULTICAST, BROADCAST & PHYSICAL ADDRESS */
#define TX_ENABLE 0x04 /* bit 2 */
#define RX_ENABLE 0x08 /* bit 3 */
#define RESET 0x80 /* set bit 7 high */
#define STOP_RESET 0x00 /* set bit 7 low */
/*
* data to command register
* (high 4 bits in write to DATA_PORT)
*/
#define RX_PAGE2_SELECT 0x10 /* bit 4, only 2 pages to select */
#define RX_BASE_PAGE 0x20 /* bit 5, always set when specifying RX_ADDR */
#define FLIP_IRQ 0x40 /* bit 6 */
/*
* D-Link adapter internal memory:
*
* 0-2K 1:st transmit page (send from pointer up to 2K)
* 2-4K 2:nd transmit page (send from pointer up to 4K)
*
* 4-6K 1:st receive page (data from 4K upwards)
* 6-8K 2:nd receive page (data from 6K upwards)
*
* 8K+ Adapter ROM (contains magic code and last 3 bytes of Ethernet address)
*/
#define MEM_2K 0x0800 /* 2048 */
#define MEM_4K 0x1000 /* 4096 */
#define MEM_6K 0x1800 /* 6144 */
#define NODE_ADDRESS 0x2000 /* 8192 */
#define RUNT 60 /* Too small Ethernet packet */
/**************************************************
* *
* End of definition *
* *
**************************************************/
/*
* Index to functions, as function prototypes.
*/
/* Routines used internally. (See "convenience macros") */
static u8 de600_read_status(struct net_device *dev);
static u8 de600_read_byte(unsigned char type, struct net_device *dev);
/* Put in the device structure. */
static int de600_open(struct net_device *dev);
static int de600_close(struct net_device *dev);
static int de600_start_xmit(struct sk_buff *skb, struct net_device *dev);
/* Dispatch from interrupts. */
static irqreturn_t de600_interrupt(int irq, void *dev_id);
static int de600_tx_intr(struct net_device *dev, int irq_status);
static void de600_rx_intr(struct net_device *dev);
/* Initialization */
static void trigger_interrupt(struct net_device *dev);
static int adapter_init(struct net_device *dev);
/*
* Convenience macros/functions for D-Link adapter
*/
#define select_prn() outb_p(SELECT_PRN, COMMAND_PORT); DE600_SLOW_DOWN
#define select_nic() outb_p(SELECT_NIC, COMMAND_PORT); DE600_SLOW_DOWN
/* Thanks for hints from Mark Burton <markb@ordern.demon.co.uk> */
#define de600_put_byte(data) ( \
outb_p(((data) << 4) | WRITE_DATA , DATA_PORT), \
outb_p(((data) & 0xf0) | WRITE_DATA | HI_NIBBLE, DATA_PORT))
/*
* The first two outb_p()'s below could perhaps be deleted if there
* would be more delay in the last two. Not certain about it yet...
*/
#define de600_put_command(cmd) ( \
outb_p(( rx_page << 4) | COMMAND , DATA_PORT), \
outb_p(( rx_page & 0xf0) | COMMAND | HI_NIBBLE, DATA_PORT), \
outb_p(((rx_page | cmd) << 4) | COMMAND , DATA_PORT), \
outb_p(((rx_page | cmd) & 0xf0) | COMMAND | HI_NIBBLE, DATA_PORT))
#define de600_setup_address(addr,type) ( \
outb_p((((addr) << 4) & 0xf0) | type , DATA_PORT), \
outb_p(( (addr) & 0xf0) | type | HI_NIBBLE, DATA_PORT), \
outb_p((((addr) >> 4) & 0xf0) | type , DATA_PORT), \
outb_p((((addr) >> 8) & 0xf0) | type | HI_NIBBLE, DATA_PORT))
#define rx_page_adr() ((rx_page & RX_PAGE2_SELECT)?(MEM_6K):(MEM_4K))
/* Flip bit, only 2 pages */
#define next_rx_page() (rx_page ^= RX_PAGE2_SELECT)
#define tx_page_adr(a) (((a) + 1) * MEM_2K)