| 2d8f648 | Georg Kohmann | 19 November 2020, 09:58:33 UTC | ipv6: Remove dependency of ipv6_frag_thdr_truncated on ipv6 module IPV6=m NF_DEFRAG_IPV6=y ld: net/ipv6/netfilter/nf_conntrack_reasm.o: in function `nf_ct_frag6_gather': net/ipv6/netfilter/nf_conntrack_reasm.c:462: undefined reference to `ipv6_frag_thdr_truncated' Netfilter is depending on ipv6 symbol ipv6_frag_thdr_truncated. This dependency is forcing IPV6=y. Remove this dependency by moving ipv6_frag_thdr_truncated out of ipv6. This is the same solution as used with a similar issues: Referring to commit 70b095c843266 ("ipv6: remove dependency of nf_defrag_ipv6 on ipv6 module") Fixes: 9d9e937b1c8b ("ipv6/netfilter: Discard first fragment not including all headers") Reported-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Georg Kohmann <geokohma@cisco.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Link: https://lore.kernel.org/r/20201119095833.8409-1-geokohma@cisco.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 19 November 2020, 18:49:50 UTC |
| f0b0a2d | Jakub Kicinski | 19 November 2020, 01:49:24 UTC | Merge tag 'linux-can-fixes-for-5.10-20201118' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2020-11-18 Jimmy Assarsson provides two patches for the kvaser_pciefd and kvaser_usb drivers, where the can_bittiming_const are fixed. The next patch is by me and fixes an erroneous flexcan_transceiver_enable() during bus-off recovery in the flexcan driver. Jarkko Nikula's patch for the m_can driver fixes the IRQ handler to only process the interrupts if the device is not suspended. * tag 'linux-can-fixes-for-5.10-20201118' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: m_can: process interrupt only when not runtime suspended can: flexcan: flexcan_chip_start(): fix erroneous flexcan_transceiver_enable() during bus-off recovery can: kvaser_usb: kvaser_usb_hydra: Fix KCAN bittiming limits can: kvaser_pciefd: Fix KCAN bittiming limits ==================== Link: https://lore.kernel.org/r/20201118160414.2731659-1-mkl@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 19 November 2020, 01:49:24 UTC |
| 6d9c8d1 | Aya Levin | 18 November 2020, 08:19:22 UTC | net/mlx4_core: Fix init_hca fields offset Slave function read the following capabilities from the wrong offset: 1. log_mc_entry_sz 2. fs_log_entry_sz 3. log_mc_hash_sz Fix that by adjusting these capabilities offset to match firmware layout. Due to the wrong offset read, the following issues might occur: 1+2. Negative value reported at max_mcast_qp_attach. 3. Driver to init FW with multicast hash size of zero. Fixes: a40ded604365 ("net/mlx4_core: Add masking for a few queries on HCA caps") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 19 November 2020, 01:46:20 UTC |
| f93e849 | Jakub Kicinski | 19 November 2020, 01:17:32 UTC | Merge tag 'mlx5-fixes-2020-11-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5 fixes 2020-11-17 This series introduces some fixes to mlx5 driver. * tag 'mlx5-fixes-2020-11-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5: fix error return code in mlx5e_tc_nic_init() net/mlx5: E-Switch, Fail mlx5_esw_modify_vport_rate if qos disabled net/mlx5: Disable QoS when min_rates on all VFs are zero net/mlx5: Clear bw_share upon VF disable net/mlx5: Add handling of port type in rule deletion net/mlx5e: Fix check if netdev is bond slave net/mlx5e: Fix IPsec packet drop by mlx5e_tc_update_skb net/mlx5e: Set IPsec WAs only in IP's non checksum partial case. net/mlx5e: Fix refcount leak on kTLS RX resync ==================== Link: https://lore.kernel.org/r/20201117195702.386113-1-saeedm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 19 November 2020, 01:17:33 UTC |
| 6dceaa9 | Sebastian Andrzej Siewior | 16 November 2020, 16:21:14 UTC | atm: nicstar: Unmap DMA on send error The `skb' is mapped for DMA in ns_send() but does not unmap DMA in case push_scqe() fails to submit the `skb'. The memory of the `skb' is released so only the DMA mapping is leaking. Unmap the DMA mapping in case push_scqe() failed. Fixes: 864a3ff635fa7 ("atm: [nicstar] remove virt_to_bus() and support 64-bit platforms") Cc: Chas Williams <3chas3@gmail.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 19 November 2020, 00:42:07 UTC |
| d8c1901 | Dongli Zhang | 15 November 2020, 20:10:29 UTC | page_frag: Recover from memory pressure The ethernet driver may allocate skb (and skb->data) via napi_alloc_skb(). This ends up to page_frag_alloc() to allocate skb->data from page_frag_cache->va. During the memory pressure, page_frag_cache->va may be allocated as pfmemalloc page. As a result, the skb->pfmemalloc is always true as skb->data is from page_frag_cache->va. The skb will be dropped if the sock (receiver) does not have SOCK_MEMALLOC. This is expected behaviour under memory pressure. However, once kernel is not under memory pressure any longer (suppose large amount of memory pages are just reclaimed), the page_frag_alloc() may still re-use the prior pfmemalloc page_frag_cache->va to allocate skb->data. As a result, the skb->pfmemalloc is always true unless page_frag_cache->va is re-allocated, even if the kernel is not under memory pressure any longer. Here is how kernel runs into issue. 1. The kernel is under memory pressure and allocation of PAGE_FRAG_CACHE_MAX_ORDER in __page_frag_cache_refill() will fail. Instead, the pfmemalloc page is allocated for page_frag_cache->va. 2: All skb->data from page_frag_cache->va (pfmemalloc) will have skb->pfmemalloc=true. The skb will always be dropped by sock without SOCK_MEMALLOC. This is an expected behaviour. 3. Suppose a large amount of pages are reclaimed and kernel is not under memory pressure any longer. We expect skb->pfmemalloc drop will not happen. 4. Unfortunately, page_frag_alloc() does not proactively re-allocate page_frag_alloc->va and will always re-use the prior pfmemalloc page. The skb->pfmemalloc is always true even kernel is not under memory pressure any longer. Fix this by freeing and re-allocating the page instead of recycling it. References: https://lore.kernel.org/lkml/20201103193239.1807-1-dongli.zhang@oracle.com/ References: https://lore.kernel.org/linux-mm/20201105042140.5253-1-willy@infradead.org/ Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Aruna Ramakrishna <aruna.ramakrishna@oracle.com> Cc: Bert Barbe <bert.barbe@oracle.com> Cc: Rama Nichanamatlu <rama.nichanamatlu@oracle.com> Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Cc: Manjunath Patil <manjunath.b.patil@oracle.com> Cc: Joe Jin <joe.jin@oracle.com> Cc: SRINIVAS <srinivas.eeda@oracle.com> Fixes: 79930f5892e1 ("net: do not deplete pfmemalloc reserve") Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20201115201029.11903-1-dongli.zhang@oracle.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 23:21:56 UTC |
| a3dcb3e | Andrew Lunn | 16 November 2020, 16:43:01 UTC | net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset When the switch is hardware reset, it reads the contents of the EEPROM. This can contain instructions for programming values into registers and to perform waits between such programming. Reading the EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits after deasserting the reset GPIO. So poll the EEPROM done bit to ensure it is complete. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Ruslan Sushko <rus@sushko.dev> Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 19:24:44 UTC |
| fc2635b | Jakub Kicinski | 18 November 2020, 19:07:03 UTC | Merge branch 'mlxsw-couple-of-fixes' Ido Schimmel says: ==================== mlxsw: Couple of fixes Patch #1 fixes firmware flashing when CONFIG_MLXSW_CORE=y and CONFIG_MLXFW=m. Patch #2 prevents EMAD transactions from needlessly failing when the system is under heavy load by using exponential backoff. Please consider patch #2 for stable. ==================== Link: https://lore.kernel.org/r/20201117173352.288491-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 19:07:04 UTC |
| 1f492ea | Ido Schimmel | 17 November 2020, 17:33:52 UTC | mlxsw: core: Use variable timeout for EMAD retries The driver sends Ethernet Management Datagram (EMAD) packets to the device for configuration purposes and waits for up to 200ms for a reply. A request is retried up to 5 times. When the system is under heavy load, replies are not always processed in time and EMAD transactions fail. Make the process more robust to such delays by using exponential backoff. First wait for up to 200ms, then retransmit and wait for up to 400ms and so on. Fixes: caf7297e7ab5 ("mlxsw: core: Introduce support for asynchronous EMAD register access") Reported-by: Denis Yulevich <denisyu@nvidia.com> Tested-by: Denis Yulevich <denisyu@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 19:07:00 UTC |
| fb738b9 | Ido Schimmel | 17 November 2020, 17:33:51 UTC | mlxsw: Fix firmware flashing The commit cited below moved firmware flashing functionality from mlxsw_spectrum to mlxsw_core, but did not adjust the Kconfig dependencies. This makes it possible to have mlxsw_core as built-in and mlxfw as a module. The mlxfw code is therefore not reachable from mlxsw_core and firmware flashing fails: # devlink dev flash pci/0000:01:00.0 file mellanox/mlxsw_spectrum-13.2008.1310.mfa2 devlink answers: Operation not supported Fix by having mlxsw_core select mlxfw. Fixes: b79cb787ac70 ("mlxsw: Move fw flashing code into core.c") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reported-by: Vadim Pasternak <vadimp@nvidia.com> Tested-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 19:07:00 UTC |
| 1532b97 | Florian Fainelli | 17 November 2020, 03:52:34 UTC | net: Have netpoll bring-up DSA management interface DSA network devices rely on having their DSA management interface up and running otherwise their ndo_open() will return -ENETDOWN. Without doing this it would not be possible to use DSA devices as netconsole when configured on the command line. These devices also do not utilize the upper/lower linking so the check about the netpoll device having upper is not going to be a problem. The solution adopted here is identical to the one done for net/ipv4/ipconfig.c with 728c02089a0e ("net: ipv4: handle DSA enabled master network devices"), with the network namespace scope being restricted to that of the process configuring netpoll. Fixes: 04ff53f96a93 ("net: dsa: Add netconsole support") Tested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20201117035236.22658-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 19:04:11 UTC |
| 3a36060 | Zhang Changzhong | 17 November 2020, 02:57:55 UTC | atl1e: fix error return code in atl1e_probe() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: a6a5325239c2 ("atl1e: Atheros L1E Gigabit Ethernet driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605581875-36281-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 19:02:15 UTC |
| 537a147 | Zhang Changzhong | 17 November 2020, 02:55:21 UTC | atl1c: fix error return code in atl1c_probe() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 43250ddd75a3 ("atl1c: Atheros L1C Gigabit Ethernet driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605581721-36028-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 19:00:17 UTC |
| a5ebcbd | Zhang Changzhong | 17 November 2020, 02:45:05 UTC | ah6: fix error return code in ah6_input() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605581105-35295-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 18:53:16 UTC |
| df8d85d | Filip Moc | 17 November 2020, 17:36:31 UTC | net: usb: qmi_wwan: Set DTR quirk for MR400 LTE module MR400 embedded in TL-MR6400 v4 requires DTR to be set. Signed-off-by: Filip Moc <dev@moc6.cz> Acked-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20201117173631.GA550981@moc6.cz Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 18:49:15 UTC |
| a1f6344 | Jarkko Nikula | 15 September 2020, 13:47:15 UTC | can: m_can: process interrupt only when not runtime suspended Avoid processing bogus interrupt statuses when the HW is runtime suspended and the M_CAN_IR register read may get all bits 1's. Handler can be called if the interrupt request is shared with other peripherals or at the end of free_irq(). Therefore check the runtime suspended status before processing. Fixes: cdf8259d6573 ("can: m_can: Add PM Support") Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 18 November 2020, 15:37:32 UTC |
| cd9f13c | Marc Kleine-Budde | 18 November 2020, 15:01:48 UTC | can: flexcan: flexcan_chip_start(): fix erroneous flexcan_transceiver_enable() during bus-off recovery If the CAN controller goes into bus off, the do_set_mode() callback with CAN_MODE_START can be used to recover the controller, which then calls flexcan_chip_start(). If configured, this is done automatically by the framework or manually by the user. In flexcan_chip_start() there is an explicit call to flexcan_transceiver_enable(), which does a regulator_enable() on the transceiver regulator. This results in a net usage counter increase, as there is no corresponding flexcan_transceiver_disable() in the bus off code path. This further leads to the transceiver stuck enabled, even if the CAN interface is shut down. To fix this problem the flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close(). Fixes: e955cead0311 ("CAN: Add Flexcan CAN controller driver") Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 18 November 2020, 15:02:34 UTC |
| d003868 | Jimmy Assarsson | 15 November 2020, 16:30:23 UTC | can: kvaser_usb: kvaser_usb_hydra: Fix KCAN bittiming limits Use correct bittiming limits for the KCAN CAN controller. Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family") Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/r/20201115163027.16851-2-jimmyassarsson@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 18 November 2020, 08:06:35 UTC |
| 470e14c | Jimmy Assarsson | 15 November 2020, 16:30:22 UTC | can: kvaser_pciefd: Fix KCAN bittiming limits Use correct bittiming limits for the KCAN CAN controller. Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices") Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/r/20201115163027.16851-1-jimmyassarsson@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 18 November 2020, 08:06:35 UTC |
| c09c8a2 | Florian Klink | 15 November 2020, 22:45:09 UTC | ipv4: use IS_ENABLED instead of ifdef Checking for ifdef CONFIG_x fails if CONFIG_x=m. Use IS_ENABLED instead, which is true for both built-ins and modules. Otherwise, a > ip -4 route add 1.2.3.4/32 via inet6 fe80::2 dev eth1 fails with the message "Error: IPv6 support not enabled in kernel." if CONFIG_IPV6 is `m`. In the spirit of b8127113d01e53adba15b41aefd37b90ed83d631. Fixes: d15662682db2 ("ipv4: Allow ipv6 gateway with ipv4 routes") Cc: Kim Phillips <kim.phillips@arm.com> Signed-off-by: Florian Klink <flokli@flokli.de> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20201115224509.2020651-1-flokli@flokli.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 01:02:03 UTC |
| 93be526 | Dmitry Bogdanov | 16 November 2020, 13:29:44 UTC | qed: fix ILT configuration of SRC block The code refactoring of ILT configuration was not complete, the old unused variables were used for the SRC block. That could lead to the memory corruption by HW when rx filters are configured. This patch completes that refactoring. Fixes: 8a52bbab39c9 (qed: Debug feature: ilt and mdump) Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Link: https://lore.kernel.org/r/20201116132944.2055-1-dbogdanov@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 00:35:32 UTC |
| e33de7c | Wang Hai | 16 November 2020, 08:20:18 UTC | inet_diag: Fix error path to cancel the meseage in inet_req_diag_fill() nlmsg_cancel() needs to be called in the error path of inet_req_diag_fill to cancel the message. Fixes: d545caca827b ("net: inet: diag: expose the socket mark to privileged processes.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Link: https://lore.kernel.org/r/20201116082018.16496-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 18 November 2020, 00:08:36 UTC |
| 138559b | Tariq Toukan | 15 November 2020, 13:14:48 UTC | net/tls: Fix wrong record sn in async mode of device resync In async_resync mode, we log the TCP seq of records until the async request is completed. Later, in case one of the logged seqs matches the resync request, we return it, together with its record serial number. Before this fix, we mistakenly returned the serial number of the current record instead. Fixes: ed9b7646b06a ("net/tls: Add asynchronous resync") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Boris Pismenny <borisp@nvidia.com> Link: https://lore.kernel.org/r/20201115131448.2702-1-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 22:41:20 UTC |
| a5bbcbf | Taehee Yoo | 15 November 2020, 10:30:41 UTC | netdevsim: set .owner to THIS_MODULE If THIS_MODULE is not set, the module would be removed while debugfs is being used. It eventually makes kernel panic. Fixes: 82c93a87bf8b ("netdevsim: implement couple of testing devlink health reporters") Fixes: 424be63ad831 ("netdevsim: add UDP tunnel port offload support") Fixes: 4418f862d675 ("netdevsim: implement support for devlink region and snapshots") Fixes: d3cbb907ae57 ("netdevsim: add ACL trap reporting cookie as a metadata") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Link: https://lore.kernel.org/r/20201115103041.30701-1-ap420073@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 22:08:59 UTC |
| fd5736b | Alex Marginean | 12 November 2020, 18:26:08 UTC | enetc: Workaround for MDIO register access issue Due to a hardware issue, an access to MDIO registers that is concurrent with other ENETC register accesses may lead to the MDIO access being dropped or corrupted. The workaround introduces locking for all register accesses to the ENETC register space. To reduce performance impact, a readers-writers locking scheme has been implemented. The writer in this case is the MDIO access code (irrelevant whether that MDIO access is a register read or write), and the reader is any access code to non-MDIO ENETC registers. Also, the datapath functions acquire the read lock fewer times and use _hot accessors. All the rest of the code uses the _wa accessors which lock every register access. The commit introducing MDIO support is - commit ebfcb23d62ab ("enetc: Add ENETC PF level external MDIO support") but due to subsequent refactoring this patch is applicable on top of a later commit. Fixes: 6517798dd343 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl") Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20201112182608.26177-1-claudiu.manoil@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 20:12:12 UTC |
| 68ec32d | Wang Hai | 14 November 2020, 11:52:23 UTC | net/mlx5: fix error return code in mlx5e_tc_nic_init() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: aedd133d17bc ("net/mlx5e: Support CT offload for tc nic flows") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:54 UTC |
| 5b8631c | Eli Cohen | 09 November 2020, 09:35:52 UTC | net/mlx5: E-Switch, Fail mlx5_esw_modify_vport_rate if qos disabled Avoid calling mlx5_esw_modify_vport_rate() if qos is not enabled and avoid unnecessary syndrome messages from firmware. Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support") Signed-off-by: Eli Cohen <elic@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:53 UTC |
| 470b747 | Vladyslav Tarasiuk | 21 October 2020, 08:05:41 UTC | net/mlx5: Disable QoS when min_rates on all VFs are zero Currently when QoS is enabled for VF and any min_rate is configured, the driver sets bw_share value to at least 1 and doesn’t allow to set it to 0 to make minimal rate unlimited. It means there is always a minimal rate configured for every VF, even if user tries to remove it. In order to make QoS disable possible, check whether all vports have configured min_rate = 0. If this is true, set their bw_share to 0 to disable min_rate limitations. Fixes: c9497c98901c ("net/mlx5: Add support for setting VF min rate") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:53 UTC |
| 1ce5fc7 | Vladyslav Tarasiuk | 02 November 2020, 11:45:24 UTC | net/mlx5: Clear bw_share upon VF disable Currently, if user disables VFs with some min and max rates configured, they are cleared. But QoS data is not cleared and restored upon next VF enable placing limits on minimal rate for given VF, when user expects none. To match cleared vport->info struct with QoS-related min and max rates upon VF disable, clear vport->qos struct too. Fixes: 556b9d16d3f5 ("net/mlx5: Clear VF's configuration on disabling SRIOV") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:53 UTC |
| 8cbcc5e | Michael Guralnik | 02 November 2020, 15:34:44 UTC | net/mlx5: Add handling of port type in rule deletion Handle destruction of rules with port destination type to enable full destruction of flow. Without this handling of TX rules the deletion of these rules fails. Dmesg of flow destruction failure: [ 203.714146] mlx5_core 0000:00:0b.0: mlx5_cmd_check:753:(pid 342): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x144b7a) [ 210.547387] ------------[ cut here ]------------ [ 210.548663] refcount_t: decrement hit 0; leaking memory. [ 210.550651] WARNING: CPU: 4 PID: 342 at lib/refcount.c:31 refcount_warn_saturate+0x5c/0x110 [ 210.550654] Modules linked in: mlx5_ib mlx5_core ib_ipoib rdma_ucm rdma_cm iw_cm ib_cm ib_umad ib_uverbs ib_core [ 210.550675] CPU: 4 PID: 342 Comm: test Not tainted 5.8.0-rc2+ #116 [ 210.550678] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 210.550680] RIP: 0010:refcount_warn_saturate+0x5c/0x110 [ 210.550685] Code: c6 d1 1b 01 00 0f 84 ad 00 00 00 5b 5d c3 80 3d b5 d1 1b 01 00 75 f4 48 c7 c7 20 d1 15 82 c6 05 a5 d1 1b 01 01 e8 a7 eb af ff <0f> 0b eb dd 80 3d 99 d1 1b 01 00 75 d4 48 c7 c7 c0 cf 15 82 c6 05 [ 210.550687] RSP: 0018:ffff8881642e77e8 EFLAGS: 00010282 [ 210.550691] RAX: 0000000000000000 RBX: 0000000000000004 RCX: 0000000000000000 [ 210.550694] RDX: 0000000000000027 RSI: 0000000000000004 RDI: ffffed102c85ceef [ 210.550696] RBP: ffff888161720428 R08: ffffffff8124c10e R09: ffffed103243beae [ 210.550698] R10: ffff8881921df56b R11: ffffed103243bead R12: ffff8881841b4180 [ 210.550701] R13: ffff888161720428 R14: ffff8881616d0000 R15: ffff888161720380 [ 210.550704] FS: 00007fc27f025740(0000) GS:ffff888192000000(0000) knlGS:0000000000000000 [ 210.550706] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 210.550708] CR2: 0000557e4b41a6a0 CR3: 0000000002415004 CR4: 0000000000360ea0 [ 210.550711] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 210.550713] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 210.550715] Call Trace: [ 210.550717] mlx5_del_flow_rules+0x484/0x490 [mlx5_core] [ 210.550720] ? mlx5_cmd_set_fte+0xa80/0xa80 [mlx5_core] [ 210.550722] mlx5_ib_destroy_flow+0x17f/0x280 [mlx5_ib] [ 210.550724] uverbs_free_flow+0x4c/0x90 [ib_uverbs] [ 210.550726] destroy_hw_idr_uobject+0x41/0xb0 [ib_uverbs] [ 210.550728] uverbs_destroy_uobject+0xaa/0x390 [ib_uverbs] [ 210.550731] __uverbs_cleanup_ufile+0x129/0x1b0 [ib_uverbs] [ 210.550733] ? uverbs_destroy_uobject+0x390/0x390 [ib_uverbs] [ 210.550735] uverbs_destroy_ufile_hw+0x78/0x190 [ib_uverbs] [ 210.550737] ib_uverbs_close+0x36/0x140 [ib_uverbs] [ 210.550739] __fput+0x181/0x380 [ 210.550741] task_work_run+0x88/0xd0 [ 210.550743] do_exit+0x5f6/0x13b0 [ 210.550745] ? sched_clock_cpu+0x30/0x140 [ 210.550747] ? is_current_pgrp_orphaned+0x70/0x70 [ 210.550750] ? lock_downgrade+0x360/0x360 [ 210.550752] ? mark_held_locks+0x1d/0x90 [ 210.550754] do_group_exit+0x8a/0x140 [ 210.550756] get_signal+0x20a/0xf50 [ 210.550758] do_signal+0x8c/0xbe0 [ 210.550760] ? hrtimer_nanosleep+0x1d8/0x200 [ 210.550762] ? nanosleep_copyout+0x50/0x50 [ 210.550764] ? restore_sigcontext+0x320/0x320 [ 210.550766] ? __hrtimer_init+0xf0/0xf0 [ 210.550768] ? timespec64_add_safe+0x150/0x150 [ 210.550770] ? mark_held_locks+0x1d/0x90 [ 210.550772] ? lockdep_hardirqs_on_prepare+0x14c/0x240 [ 210.550774] __prepare_exit_to_usermode+0x119/0x170 [ 210.550776] do_syscall_64+0x65/0x300 [ 210.550778] ? trace_hardirqs_off+0x10/0x120 [ 210.550781] ? mark_held_locks+0x1d/0x90 [ 210.550783] ? asm_sysvec_apic_timer_interrupt+0xa/0x20 [ 210.550785] ? lockdep_hardirqs_on+0x112/0x190 [ 210.550787] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 210.550789] RIP: 0033:0x7fc27f1cd157 [ 210.550791] Code: Bad RIP value. [ 210.550793] RSP: 002b:00007ffd4db27ea8 EFLAGS: 00000246 ORIG_RAX: 0000000000000023 [ 210.550798] RAX: fffffffffffffdfc RBX: ffffffffffffff80 RCX: 00007fc27f1cd157 [ 210.550800] RDX: 00007fc27f025740 RSI: 00007ffd4db27eb0 RDI: 00007ffd4db27eb0 [ 210.550803] RBP: 0000000000000016 R08: 0000000000000000 R09: 000000000000000e [ 210.550805] R10: 00007ffd4db27dc7 R11: 0000000000000246 R12: 0000000000400c00 [ 210.550808] R13: 00007ffd4db285f0 R14: 0000000000000000 R15: 0000000000000000 [ 210.550809] irq event stamp: 49399 [ 210.550812] hardirqs last enabled at (49399): [<ffffffff81172d36>] console_unlock+0x556/0x6f0 [ 210.550815] hardirqs last disabled at (49398): [<ffffffff81172897>] console_unlock+0xb7/0x6f0 [ 210.550818] softirqs last enabled at (48706): [<ffffffff81e0037b>] __do_softirq+0x37b/0x60c [ 210.550820] softirqs last disabled at (48697): [<ffffffff81c00e2f>] asm_call_on_stack+0xf/0x20 [ 210.550822] ---[ end trace ad18c0e6fa846454 ]--- [ 210.581862] mlx5_core 0000:00:0c.0: mlx5_destroy_flow_table:2132:(pid 342): Flow table 262150 wasn't destroyed, refcount > 1 Fixes: a7ee18bdee83 ("RDMA/mlx5: Allow creating a matcher for a NIC TX flow table") Signed-off-by: Michael Guralnik <michaelgur@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:52 UTC |
| 219b326 | Maor Dickman | 04 November 2020, 12:10:30 UTC | net/mlx5e: Fix check if netdev is bond slave Bond events handler uses bond_slave_get_rtnl to check if net device is bond slave. bond_slave_get_rtnl return the rcu rx_handler pointer from the netdev which exists for bond slaves but also exists for devices that are attached to linux bridge so using it as indication for bond slave is wrong. Fix by using netif_is_lag_port instead. Fixes: 7e51891a237f ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Reviewed-by: Ariel Levkovich <lariel@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:52 UTC |
| 6248ce9 | Huy Nguyen | 03 November 2020, 18:56:18 UTC | net/mlx5e: Fix IPsec packet drop by mlx5e_tc_update_skb Both TC and IPsec crypto offload use metadata_regB to store private information. Since TC does not use bit 31 of regB, IPsec will use bit 31 as the IPsec packet marker. The IPsec's regB usage is changed to: Bit31: IPsec marker Bit30-24: IPsec syndrome Bit23-0: IPsec obj id Fixes: b2ac7541e377 ("net/mlx5e: IPsec: Add Connect-X IPsec Rx data path offload") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Reviewed-by: Ariel Levkovich <lariel@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:52 UTC |
| 5cfb540 | Huy Nguyen | 22 October 2020, 16:22:56 UTC | net/mlx5e: Set IPsec WAs only in IP's non checksum partial case. The IP's checksum partial still requires L4 csum flag on Ethernet WQE. Make the IPsec WAs only for the IP's non checksum partial case (for example icmd packet) Fixes: 5be019040cb7 ("net/mlx5e: IPsec: Add Connect-X IPsec Tx data path offload") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Reviewed-by: Alaa Hleihel <alaa@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:52 UTC |
| ea63609 | Maxim Mikityanskiy | 08 October 2020, 09:34:10 UTC | net/mlx5e: Fix refcount leak on kTLS RX resync On resync, the driver calls inet_lookup_established (__inet6_lookup_established) that increases sk_refcnt of the socket. To decrease it, the driver set skb->destructor to sock_edemux. However, it didn't work well, because the TCP stack also sets this destructor for early demux, and the refcount gets decreased only once, while increased two times (in mlx5e and in the TCP stack). It leads to a socket leak, a TLS context leak, which in the end leads to calling tls_dev_del twice: on socket close and on driver unload, which in turn leads to a crash. This commit fixes the refcount leak by calling sock_gen_put right away after using the socket, thus fixing all the subsequent issues. Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> | 17 November 2020, 19:50:51 UTC |
| 1b9e2a8 | Ryan Sharpelletti | 16 November 2020, 17:44:13 UTC | tcp: only postpone PROBE_RTT if RTT is < current min_rtt estimate During loss recovery, retransmitted packets are forced to use TCP timestamps to calculate the RTT samples, which have a millisecond granularity. BBR is designed using a microsecond granularity. As a result, multiple RTT samples could be truncated to the same RTT value during loss recovery. This is problematic, as BBR will not enter PROBE_RTT if the RTT sample is <= the current min_rtt sample, meaning that if there are persistent losses, PROBE_RTT will constantly be pushed off and potentially never re-entered. This patch makes sure that BBR enters PROBE_RTT by checking if RTT sample is < the current min_rtt sample, rather than <=. The Netflix transport/TCP team discovered this bug in the Linux TCP BBR code during lab tests. Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Ryan Sharpelletti <sharpelletti@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Link: https://lore.kernel.org/r/20201116174412.1433277-1-sharpelletti.kdev@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 19:03:22 UTC |
| 3d51794 | Joel Stanley | 17 November 2020, 02:44:48 UTC | net: ftgmac100: Fix crash when removing driver When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific)) in net/core/dev.c due to still having the NC-SI packet handler registered. # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind ------------[ cut here ]------------ kernel BUG at net/core/dev.c:10254! Internal error: Oops - BUG: 0 [#1] SMP ARM CPU: 0 PID: 115 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00007-g02e0365710c4 #46 Hardware name: Generic DT based system PC is at netdev_run_todo+0x314/0x394 LR is at cpumask_next+0x20/0x24 pc : [<806f5830>] lr : [<80863cb0>] psr: 80000153 sp : 855bbd58 ip : 00000001 fp : 855bbdac r10: 80c03d00 r9 : 80c06228 r8 : 81158c54 r7 : 00000000 r6 : 80c05dec r5 : 80c05d18 r4 : 813b9280 r3 : 813b9054 r2 : 8122c470 r1 : 00000002 r0 : 00000002 Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none Control: 00c5387d Table: 85514008 DAC: 00000051 Process sh (pid: 115, stack limit = 0x7cb5703d) ... Backtrace: [<806f551c>] (netdev_run_todo) from [<80707eec>] (rtnl_unlock+0x18/0x1c) r10:00000051 r9:854ed710 r8:81158c54 r7:80c76bb0 r6:81158c10 r5:8115b410 r4:813b9000 [<80707ed4>] (rtnl_unlock) from [<806f5db8>] (unregister_netdev+0x2c/0x30) [<806f5d8c>] (unregister_netdev) from [<805a8180>] (ftgmac100_remove+0x20/0xa8) r5:8115b410 r4:813b9000 [<805a8160>] (ftgmac100_remove) from [<805355e4>] (platform_drv_remove+0x34/0x4c) Fixes: bd466c3fb5a4 ("net/faraday: Support NCSI mode") Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 18:59:03 UTC |
| 7b027c2 | Zhang Changzhong | 17 November 2020, 03:02:11 UTC | net: b44: fix error return code in b44_init_one() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 39a6f4bce6b4 ("b44: replace the ssb_dma API with the generic DMA API") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/1605582131-36735-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 18:50:28 UTC |
| cb47d16 | Zhang Changzhong | 16 November 2020, 13:07:13 UTC | qed: fix error return code in qed_iwarp_ll2_start() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 469981b17a4f ("qed: Add unaligned and packed packet processing") Fixes: fcb39f6c10b2 ("qed: Add mpa buffer descriptors for storing and processing mpa fpdus") Fixes: 1e28eaad07ea ("qed: Add iWARP support for fpdu spanned over more than two tcp packets") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Link: https://lore.kernel.org/r/1605532033-27373-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 18:40:34 UTC |
| d5bd32a | Jakub Kicinski | 17 November 2020, 01:39:49 UTC | Merge branch 'bnxt_en-bug-fixes' Michael Chan says: ==================== bnxt_en: Bug fixes. This first patch fixes a module eeprom A2h addressing issue. The next 2 patches fix counter related issues. The last one skips an unsupported firmware call on the VF to avoid the error log. ==================== Link: https://lore.kernel.org/r/1605486472-28156-1-git-send-email-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 01:39:49 UTC |
| 0ae0a77 | Vasundhara Volam | 16 November 2020, 00:27:52 UTC | bnxt_en: Avoid unnecessary NVM_GET_DEV_INFO cmd error log on VFs. VFs do not have access permissions to issue NVM_GET_DEV_INFO firmware command. Fixes: 4933f6753b50 ("bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 01:39:47 UTC |
| fa97f30 | Michael Chan | 16 November 2020, 00:27:51 UTC | bnxt_en: Fix counter overflow logic. bnxt_add_one_ctr() adds a hardware counter to a software counter and adjusts for the hardware counter wraparound against the mask. The logic assumes that the hardware counter is always smaller than or equal to the mask. This assumption is mostly correct. But in some cases if the firmware is older and does not provide the accurate mask, the driver can use a mask that is smaller than the actual hardware mask. This can cause some extra carry bits to be added to the software counter, resulting in counters that far exceed the actual value. Fix it by masking the hardware counter with the mask passed into bnxt_add_one_ctr(). Fixes: fea6b3335527 ("bnxt_en: Accumulate all counters.") Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 01:39:46 UTC |
| eba93de | Michael Chan | 16 November 2020, 00:27:50 UTC | bnxt_en: Free port stats during firmware reset. Firmware is unable to retain the port counters during any kind of fatal or non-fatal resets, so we must clear the port counters to avoid false detection of port counter overflow. Fixes: fea6b3335527 ("bnxt_en: Accumulate all counters.") Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 01:39:46 UTC |
| 4260330 | Edwin Peer | 16 November 2020, 00:27:49 UTC | bnxt_en: read EEPROM A2h address using page 0 The module eeprom address range returned by bnxt_get_module_eeprom() should be 256 bytes of A0h address space, the lower half of the A2h address space, and page 0 for the upper half of the A2h address space. Fix the firmware call by passing page_number 0 for the A2h slave address space. Fixes: 42ee18fe4ca2 ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO") Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 01:39:46 UTC |
| 064c9c3 | Alex Elder | 14 November 2020, 18:20:17 UTC | net: ipa: lock when freeing transaction Transactions sit on one of several lists, depending on their state (allocated, pending, complete, or polled). A spinlock protects against concurrent access when transactions are moved between these lists. Transactions are also reference counted. A newly-allocated transaction has an initial count of 1; a transaction is released in gsi_trans_free() only if its decremented reference count reaches 0. Releasing a transaction includes removing it from the polled (or if unused, allocated) list, so the spinlock is acquired when we release a transaction. The reference count is used to allow a caller to synchronously wait for a committed transaction to complete. In this case, the waiter takes an extra reference to the transaction *before* committing it (so it won't be freed), and releases its reference (calls gsi_trans_free()) when it is done with it. Similarly, gsi_channel_update() takes an extra reference to ensure a transaction isn't released before the function is done operating on it. Until the transaction is moved to the completed list (by this function) it won't be freed, so this reference is taken "safely." But in the quiesce path, we want to wait for the "last" transaction, which we find in the completed or polled list. Transactions on these lists can be freed at any time, so we (try to) prevent that by taking the reference while holding the spinlock. Currently gsi_trans_free() decrements a transaction's reference count unconditionally, acquiring the lock to remove the transaction from its list *only* when the count reaches 0. This does not protect the quiesce path, which depends on the lock to ensure its extra reference prevents release of the transaction. Fix this by only dropping the last reference to a transaction in gsi_trans_free() while holding the spinlock. Fixes: 9dd441e4ed575 ("soc: qcom: ipa: GSI transactions") Reported-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Alex Elder <elder@linaro.org> Link: https://lore.kernel.org/r/20201114182017.28270-1-elder@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 01:32:22 UTC |
| 3fe16ed | Vadim Fedorenko | 15 November 2020, 04:16:00 UTC | net/tls: fix corrupted data in recvmsg If tcp socket has more data than Encrypted Handshake Message then tls_sw_recvmsg will try to decrypt next record instead of returning full control message to userspace as mentioned in comment. The next message - usually Application Data - gets corrupted because it uses zero copy for decryption that's why the data is not stored in skb for next iteration. Revert check to not decrypt next record if current is not Application Data. Fixes: 692d7b5d1f91 ("tls: Fix recvmsg() to be able to peek across multiple records") Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Link: https://lore.kernel.org/r/1605413760-21153-1-git-send-email-vfedorenko@novek.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 01:11:02 UTC |
| fc70f5b | Subash Abhinov Kasiviswanathan | 13 November 2020, 20:12:05 UTC | net: qualcomm: rmnet: Fix incorrect receive packet handling during cleanup During rmnet unregistration, the real device rx_handler is first cleared followed by the removal of rx_handler_data after the rcu synchronization. Any packets in the receive path may observe that the rx_handler is NULL. However, there is no check when dereferencing this value to use the rmnet_port information. This fixes following splat by adding the NULL check. Unable to handle kernel NULL pointer dereference at virtual address 000000000000000d pc : rmnet_rx_handler+0x124/0x284 lr : rmnet_rx_handler+0x124/0x284 rmnet_rx_handler+0x124/0x284 __netif_receive_skb_core+0x758/0xd74 __netif_receive_skb+0x50/0x17c process_backlog+0x15c/0x1b8 napi_poll+0x88/0x284 net_rx_action+0xbc/0x23c __do_softirq+0x20c/0x48c Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Sean Tranchetti <stranche@codeaurora.org> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Link: https://lore.kernel.org/r/1605298325-3705-1-git-send-email-subashab@codeaurora.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 00:34:49 UTC |
| 9c79a8a | Lorenzo Bianconi | 13 November 2020, 18:16:57 UTC | net: mvneta: fix possible memory leak in mvneta_swbm_add_rx_fragment Recycle the page running page_pool_put_full_page() in mvneta_swbm_add_rx_fragment routine when the last descriptor contains just the FCS or if the received packet contains more than MAX_SKB_FRAGS fragments Fixes: ca0e014609f0 ("net: mvneta: move skb build after descriptors processing") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/df6a2bad70323ee58d3901491ada31c1ca2a40b9.1605291228.git.lorenzo@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 00:30:50 UTC |
| 8e5debe | Wong Vee Khee | 15 November 2020, 07:42:10 UTC | net: stmmac: Use rtnl_lock/unlock on netif_set_real_num_rx_queues() call Fix an issue where dump stack is printed on suspend resume flow due to netif_set_real_num_rx_queues() is not called with rtnl_lock held(). Fixes: 686cff3d7022 ("net: stmmac: Fix incorrect location to set real_num_rx|tx_queues") Reported-by: Christophe ROULLIER <christophe.roullier@st.com> Tested-by: Christophe ROULLIER <christophe.roullier@st.com> Cc: Alexandre TORGUE <alexandre.torgue@st.com> Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com> Link: https://lore.kernel.org/r/20201115074210.23605-1-vee.khee.wong@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 17 November 2020, 00:12:36 UTC |
| 7a30ecc | Heiner Kallweit | 13 November 2020, 09:27:27 UTC | net: bridge: add missing counters to ndo_get_stats64 callback In br_forward.c and br_input.c fields dev->stats.tx_dropped and dev->stats.multicast are populated, but they are ignored in ndo_get_stats64. Fixes: 28172739f0a2 ("net: fix 64 bit counters on 32 bit arches") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/58ea9963-77ad-a7cf-8dfd-fc95ab95f606@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 23:47:50 UTC |
| 35f735c | Zhang Changzhong | 13 November 2020, 06:49:33 UTC | net: ethernet: ti: cpsw: fix error return code in cpsw_probe() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 83a8471ba255 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605250173-18438-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 23:37:28 UTC |
| 661710b | Zhang Changzhong | 13 November 2020, 06:34:03 UTC | net: stmmac: dwmac-intel-plat: fix error return code in intel_eth_plat_probe() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 9efc9b2b04c7 ("net: stmmac: Add dwmac-intel-plat for GBE driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605249243-17262-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 23:32:30 UTC |
| 3beb9be | Zhang Changzhong | 13 November 2020, 06:16:26 UTC | qlcnic: fix error return code in qlcnic_83xx_restart_hw() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 3ced0a88cd4c ("qlcnic: Add support to run firmware POST") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605248186-16013-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 23:26:42 UTC |
| cfbaa8b | Zhang Changzhong | 13 November 2020, 06:07:07 UTC | cx82310_eth: fix error return code in cx82310_bind() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: ca139d76b0d9 ("cx82310_eth: re-enable ethernet mode after router reboot") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605247627-15385-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 23:23:44 UTC |
| 794e442 | Raju Rangoju | 16 November 2020, 10:43:22 UTC | MAINTAINERS: update cxgb4 and cxgb3 maintainer Update cxgb4 and cxgb3 driver maintainer Signed-off-by: Raju Rangoju <rajur@chelsio.com> Link: https://lore.kernel.org/r/20201116104322.3959-1-rajur@chelsio.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 22:11:46 UTC |
| 2a1828e | Martin Blumenstingl | 15 November 2020, 16:57:57 UTC | net: lantiq: Wait for the GPHY firmware to be ready A user reports (slightly shortened from the original message): libphy: lantiq,xrx200-mdio: probed mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing. gswip 1e108000.switch lan: no phy at 2 gswip 1e108000.switch lan: failed to connect to port 2: -19 lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy This is a single-port board using the internal Fast Ethernet PHY. The user reports that switching to PHY scanning instead of configuring the PHY within device-tree works around this issue. The documentation for the standalone variant of the PHY11G (which is probably very similar to what is used inside the xRX200 SoCs but having the firmware burnt onto that standalone chip in the factory) states that the PHY needs 300ms to be ready for MDIO communication after releasing the reset. Add a 300ms delay after initializing all GPHYs to ensure that the GPHY firmware had enough time to initialize and to appear on the MDIO bus. Unfortunately there is no (known) documentation on what the minimum time to wait after releasing the reset on an internal PHY so play safe and take the one for the external variant. Only wait after the last GPHY firmware is loaded to not slow down the initialization too much ( xRX200 has two GPHYs but newer SoCs have at least three GPHYs). Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 21:38:18 UTC |
| 8575245 | Xie He | 14 November 2020, 11:10:29 UTC | MAINTAINERS: Add Martin Schiller as a maintainer for the X.25 stack Martin Schiller is an active developer and reviewer for the X.25 code. His company is providing products based on the Linux X.25 stack. So he is a good candidate for maintainers of the X.25 code. The original maintainer of the X.25 network layer (Andrew Hendry) has not sent any email to the netdev mail list since 2013. So he is probably inactive now. Cc: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: Xie He <xie.he.0141@gmail.com> Acked-by: Martin Schiller <ms@dev.tdt.de> Link: https://lore.kernel.org/r/20201114111029.326972-1-xie.he.0141@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 18:20:00 UTC |
| 9d9e937 | Georg Kohmann | 11 November 2020, 11:50:25 UTC | ipv6/netfilter: Discard first fragment not including all headers Packets are processed even though the first fragment don't include all headers through the upper layer header. This breaks TAHI IPv6 Core Conformance Test v6LC.1.3.6. Referring to RFC8200 SECTION 4.5: "If the first fragment does not include all headers through an Upper-Layer header, then that fragment should be discarded and an ICMP Parameter Problem, Code 3, message should be sent to the source of the fragment, with the Pointer field set to zero." The fragment needs to be validated the same way it is done in commit 2efdaaaf883a ("IPv6: reply ICMP error if the first fragment don't include all headers") for ipv6. Wrap the validation into a common function, ipv6_frag_thdr_truncated() to check for truncation in the upper layer header. This validation does not fullfill all aspects of RFC 8200, section 4.5, but is at the moment sufficient to pass mentioned TAHI test. In netfilter, utilize the fragment offset returned by find_prev_fhdr() to let ipv6_frag_thdr_truncated() start it's traverse from the fragment header. Return 0 to drop the fragment in the netfilter. This is the same behaviour as used on other protocol errors in this function, e.g. when nf_ct_frag6_queue() returns -EPROTO. The Fragment will later be picked up by ipv6_frag_rcv() in reassembly.c. ipv6_frag_rcv() will then send an appropriate ICMP Parameter Problem message back to the source. References commit 2efdaaaf883a ("IPv6: reply ICMP error if the first fragment don't include all headers") Signed-off-by: Georg Kohmann <geokohma@cisco.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Link: https://lore.kernel.org/r/20201111115025.28879-1-geokohma@cisco.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 18:15:11 UTC |
| 7953446 | Jakub Kicinski | 16 November 2020, 17:37:13 UTC | Merge branch 'fix-usage-counter-leak-by-adding-a-general-sync-ops' Zhang Qilong says: ==================== Fix usage counter leak by adding a general sync ops In many case, we need to check return value of pm_runtime_get_sync, but it brings a trouble to the usage counter processing. Many callers forget to decrease the usage counter when it failed, which could resulted in reference leak. It has been discussed a lot[0][1]. So we add a function to deal with the usage counter for better coding and view. Then, we replace pm_runtime_resume_and_get with it in fec_main.c to avoid it. [0] https://lkml.org/lkml/2020/6/14/88 [1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139 ==================== Link: https://lore.kernel.org/r/20201110092933.3342784-1-zhangqilong3@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 17:37:13 UTC |
| da875fa | Zhang Qilong | 10 November 2020, 09:29:33 UTC | net: fec: Fix reference count leak in fec series ops pm_runtime_get_sync() will increment pm usage at first and it will resume the device later. If runtime of the device has error or device is in inaccessible state(or other error state), resume operation will fail. If we do not call put operation to decrease the reference, it will result in reference count leak. Moreover, this device cannot enter the idle state and always stay busy or other non-idle state later. So we fixed it by replacing it with pm_runtime_resume_and_get. Fixes: 8fff755e9f8d0 ("net: fec: Ensure clocks are enabled while using mdio bus") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 17:37:01 UTC |
| dd8088d | Zhang Qilong | 10 November 2020, 09:29:32 UTC | PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter In many case, we need to check return value of pm_runtime_get_sync, but it brings a trouble to the usage counter processing. Many callers forget to decrease the usage counter when it failed, which could resulted in reference leak. It has been discussed a lot[0][1]. So we add a function to deal with the usage counter for better coding. [0]https://lkml.org/lkml/2020/6/14/88 [1]https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139 Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 17:37:01 UTC |
| e2142ef | Jakub Kicinski | 16 November 2020, 15:34:30 UTC | Merge tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2020-11-15 Anant Thazhemadam contributed two patches for the AF_CAN that prevent potential access of uninitialized member in can_rcv() and canfd_rcv(). The next patch is by Alejandro Concepcion Rodriguez and changes can_restart() to use the correct function to push a skb into the networking stack from process context. Zhang Qilong's patch fixes a memory leak in the error path of the ti_hecc's probe function. A patch by me fixes mcba_usb_start_xmit() function in the mcba_usb driver, to first fill the skb and then pass it to can_put_echo_skb(). Colin Ian King's patch fixes a potential integer overflow on shift in the peak_usb driver. The next two patches target the flexcan driver, a patch by me adds the missing "req_bit" to the stop mode property comment (which was broken during net-next for v5.10). Zhang Qilong's patch fixes the failure handling of pm_runtime_get_sync(). The next seven patches target the m_can driver including the tcan4x5x spi driver glue code. Enric Balletbo i Serra's patch for the tcan4x5x Kconfig fix the REGMAP_SPI dependency handling. A patch by me for the tcan4x5x driver's probe() function adds missing error handling to for devm_regmap_init(), and in tcan4x5x_can_remove() the order of deregistration is fixed. Wu Bo's patch for the m_can driver fixes the state change handling in m_can_handle_state_change(). Two patches by Dan Murphy first introduce m_can_class_free_dev() and then make use of it to fix the freeing of the can device. A patch by Faiz Abbas add a missing shutdown of the CAN controller in the m_can_stop() function. * tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: m_can: m_can_stop(): set device to software init mode before closing can: m_can: Fix freeing of can device from peripherials can: m_can: m_can_class_free_dev(): introduce new function can: m_can: m_can_handle_state_change(): fix state change can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init() can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI can: flexcan: fix failure handling of pm_runtime_get_sync() can: flexcan: flexcan_setup_stop_mode(): add missing "req_bit" to stop mode property comment can: peak_usb: fix potential integer overflow on shift of a int can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb() can: ti_hecc: Fix memleak in ti_hecc_probe can: dev: can_restart(): post buffer from the right context can: af_can: prevent potential access of uninitialized member in canfd_rcv() can: af_can: prevent potential access of uninitialized member in can_rcv() ==================== Link: https://lore.kernel.org/r/20201115174131.2089251-1-mkl@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 16 November 2020, 15:34:30 UTC |
| a584e9b | Faiz Abbas | 25 August 2020, 05:54:42 UTC | can: m_can: m_can_stop(): set device to software init mode before closing There might be some requests pending in the buffer when the interface close sequence occurs. In some devices, these pending requests might lead to the module not shutting down properly when m_can_clk_stop() is called. Therefore, move the device to init state before potentially powering it down. Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support") Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Dan Murphy <dmurphy@ti.com> Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:33:45 UTC |
| 85816ab | Dan Murphy | 27 February 2020, 18:38:29 UTC | can: m_can: Fix freeing of can device from peripherials Fix leaking netdev device from peripherial devices. The call to allocate the netdev device is made from and managed by the peripherial. Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework") Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:33:45 UTC |
| a8c22f5 | Dan Murphy | 27 February 2020, 18:38:29 UTC | can: m_can: m_can_class_free_dev(): introduce new function This patch creates a common function that peripherials can call to free the netdev device when failures occur. Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework") Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:33:42 UTC |
| cd0d83e | Wu Bo | 29 January 2020, 02:23:30 UTC | can: m_can: m_can_handle_state_change(): fix state change m_can_handle_state_change() is called with the new_state as an argument. In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the following code indicate that a CAN_STATE_ERROR_WARNING is handled. This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING. Signed-off-by: Wu Bo <wubo.oduw@gmail.com> Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com Cc: Dan Murphy <dmurphy@ti.com> Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:36 UTC |
| c81d0b6 | Marc Kleine-Budde | 10 August 2020, 20:23:49 UTC | can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration Change the order in tcan4x5x_can_remove() to be the exact inverse of tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the device. Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:36 UTC |
| 1ff203b | Marc Kleine-Budde | 03 January 2020, 10:30:34 UTC | can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init() This patch adds the missing error checking when initializing the regmap interface fails. Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: Dan Murphy <dmurphy@ti.com> Link: http://lore.kernel.org/r/20201019154233.1262589-7-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:36 UTC |
| 3fcce13 | Enric Balletbo i Serra | 13 April 2020, 14:10:13 UTC | can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI regmap is a library function that gets selected by drivers that need it. No driver modules should depend on it. Instead depends on SPI and select REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another driver already selected REGMAP_SPI, as the symbol can't be selected through the menu kernel configuration. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.com Reviewed-by: Dan Murphy <dmurphy@ti.com> Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:36 UTC |
| b7ee5bc | Zhang Qilong | 08 November 2020, 08:30:00 UTC | can: flexcan: fix failure handling of pm_runtime_get_sync() pm_runtime_get_sync() will increment pm usage at first and it will resume the device later. If runtime of the device has error or device is in inaccessible state(or other error state), resume operation will fail. If we do not call put operation to decrease the reference, it will result in reference leak in the two functions flexcan_get_berr_counter() and flexcan_open(). Moreover, this device cannot enter the idle state and always stay busy or other non-idle state later. So we should fix it through adding pm_runtime_put_noidle(). Fixes: ca10989632d88 ("can: flexcan: implement can Runtime PM") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201108083000.2599705-1-zhangqilong3@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:35 UTC |
| 499aa92 | Marc Kleine-Budde | 14 October 2020, 11:41:36 UTC | can: flexcan: flexcan_setup_stop_mode(): add missing "req_bit" to stop mode property comment In the patch d9b081e3fc4b ("can: flexcan: remove ack_grp and ack_bit handling from driver") the unused ack_grp and ack_bit were removed from the driver. However in the comment, the "req_bit" was accidentally removed, too. This patch adds back the "req_bit" bit. Fixes: d9b081e3fc4b ("can: flexcan: remove ack_grp and ack_bit handling from driver") Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com> Link: http://lore.kernel.org/r/20201014114810.2911135-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:35 UTC |
| 8a68cc0 | Colin Ian King | 05 November 2020, 11:24:27 UTC | can: peak_usb: fix potential integer overflow on shift of a int The left shift of int 32 bit integer constant 1 is evaluated using 32 bit arithmetic and then assigned to a signed 64 bit variable. In the case where time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow. Avoid this by shifting using the BIT_ULL macro instead. Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:35 UTC |
| 81c9c8e | Marc Kleine-Budde | 28 August 2019, 19:16:55 UTC | can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb() The driver has to first fill the skb with data and then handle it to can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before sending the skb out via USB. Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com> Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:35 UTC |
| 7968c7c | Zhang Qilong | 14 November 2020, 11:17:08 UTC | can: ti_hecc: Fix memleak in ti_hecc_probe In the error handling, we should goto the probe_exit_candev to free ndev to prevent memory leak. Fixes: dabf54dd1c63 ("can: ti_hecc: Convert TI HECC driver to DT only driver") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201114111708.3465543-1-zhangqilong3@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:35 UTC |
| a1e6540 | Alejandro Concepcion Rodriguez | 05 November 2020, 21:51:47 UTC | can: dev: can_restart(): post buffer from the right context netif_rx() is meant to be called from interrupt contexts. can_restart() may be called by can_restart_work(), which is called from a worqueue, so it may run in process context. Use netif_rx_ni() instead. Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface") Co-developed-by: Loris Fauster <loris.fauster@ttcontrol.com> Signed-off-by: Loris Fauster <loris.fauster@ttcontrol.com> Signed-off-by: Alejandro Concepcion Rodriguez <alejandro@acoro.eu> Link: https://lore.kernel.org/r/4e84162b-fb31-3a73-fa9a-9438b4bd5234@acoro.eu [mkl: use netif_rx_ni() instead of netif_rx_any_context()] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:35 UTC |
| 9aa9379 | Anant Thazhemadam | 03 November 2020, 21:39:06 UTC | can: af_can: prevent potential access of uninitialized member in canfd_rcv() In canfd_rcv(), cfd->len is uninitialized when skb->len = 0, and this uninitialized cfd->len is accessed nonetheless by pr_warn_once(). Fix this uninitialized variable access by checking cfd->len's validity condition (cfd->len > CANFD_MAX_DLEN) separately after the skb->len's condition is checked, and appropriately modify the log messages that are generated as well. In case either of the required conditions fail, the skb is freed and NET_RX_DROP is returned, same as before. Fixes: d4689846881d ("can: af_can: canfd_rcv(): replace WARN_ONCE by pr_warn_once") Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Link: https://lore.kernel.org/r/20201103213906.24219-3-anant.thazhemadam@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:24:33 UTC |
| c8c958a | Anant Thazhemadam | 03 November 2020, 21:39:05 UTC | can: af_can: prevent potential access of uninitialized member in can_rcv() In can_rcv(), cfd->len is uninitialized when skb->len = 0, and this uninitialized cfd->len is accessed nonetheless by pr_warn_once(). Fix this uninitialized variable access by checking cfd->len's validity condition (cfd->len > CAN_MAX_DLEN) separately after the skb->len's condition is checked, and appropriately modify the log messages that are generated as well. In case either of the required conditions fail, the skb is freed and NET_RX_DROP is returned, same as before. Fixes: 8cb68751c115 ("can: af_can: can_rcv(): replace WARN_ONCE by pr_warn_once") Reported-by: syzbot+9bcb0c9409066696d3aa@syzkaller.appspotmail.com Tested-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Link: https://lore.kernel.org/r/20201103213906.24219-2-anant.thazhemadam@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> | 15 November 2020, 17:17:04 UTC |
| 849920c | Wang Hai | 13 November 2020, 11:16:22 UTC | devlink: Add missing genlmsg_cancel() in devlink_nl_sb_port_pool_fill() If sb_occ_port_pool_get() failed in devlink_nl_sb_port_pool_fill(), msg should be canceled by genlmsg_cancel(). Fixes: df38dafd2559 ("devlink: implement shared buffer occupancy monitoring interface") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Link: https://lore.kernel.org/r/20201113111622.11040-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 15 November 2020, 00:23:19 UTC |
| 56311a3 | Jisheng Zhang | 13 November 2020, 01:09:02 UTC | net: stmmac: dwmac_lib: enlarge dma reset timeout If the phy enables power saving technology, the dwmac's software reset needs more time to complete, enlarge dma reset timeout to 200000us. Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Link: https://lore.kernel.org/r/20201113090902.5c7aab1a@xhacker.debian Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 15 November 2020, 00:04:02 UTC |
| 796a266 | Sven Van Asbroeck | 12 November 2020, 20:47:41 UTC | lan743x: prevent entire kernel HANG on open, for some platforms On arm imx6, when opening the chip's netdev, the whole Linux kernel intermittently hangs/freezes. This is caused by a bug in the driver code which tests if pcie interrupts are working correctly, using the software interrupt: 1. open: enable the software interrupt 2. open: tell the chip to assert the software interrupt 3. open: wait for flag 4. ISR: acknowledge s/w interrupt, set flag 5. open: notice flag, disable the s/w interrupt, continue Unfortunately the ISR only acknowledges the s/w interrupt, but does not disable it. This will re-trigger the ISR in a tight loop. On some (lucky) platforms, open proceeds to disable the s/w interrupt even while the ISR is 'spinning'. On arm imx6, the spinning ISR does not allow open to proceed, resulting in a hung Linux kernel. Fix minimally by disabling the s/w interrupt in the ISR, which will prevent it from spinning. This won't break anything because the s/w interrupt is used as a one-shot interrupt. Note that this is a minimal fix, overlooking many possible cleanups, e.g.: - lan743x_intr_software_isr() is completely redundant and reads INT_STS twice for no apparent reason - disabling the s/w interrupt in lan743x_intr_test_isr() is now redundant, but harmless - waiting on software_isr_flag can be converted from a sleeping poll loop to wait_event_timeout() Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # arm imx6 lan7430 Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com> Link: https://lore.kernel.org/r/20201112204741.12375-1-TheSven73@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 23:25:12 UTC |
| e35df62 | Sven Van Asbroeck | 12 November 2020, 18:59:49 UTC | lan743x: fix issue causing intermittent kernel log warnings When running this chip on arm imx6, we intermittently observe the following kernel warning in the log, especially when the system is under high load: [ 50.119484] ------------[ cut here ]------------ [ 50.124377] WARNING: CPU: 0 PID: 303 at kernel/softirq.c:169 __local_bh_enable_ip+0x100/0x184 [ 50.132925] IRQs not enabled as expected [ 50.159250] CPU: 0 PID: 303 Comm: rngd Not tainted 5.7.8 #1 [ 50.164837] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 50.171395] [<c0111a38>] (unwind_backtrace) from [<c010be28>] (show_stack+0x10/0x14) [ 50.179162] [<c010be28>] (show_stack) from [<c05b9dec>] (dump_stack+0xac/0xd8) [ 50.186408] [<c05b9dec>] (dump_stack) from [<c0122e40>] (__warn+0xd0/0x10c) [ 50.193391] [<c0122e40>] (__warn) from [<c0123238>] (warn_slowpath_fmt+0x98/0xc4) [ 50.200892] [<c0123238>] (warn_slowpath_fmt) from [<c012b010>] (__local_bh_enable_ip+0x100/0x184) [ 50.209860] [<c012b010>] (__local_bh_enable_ip) from [<bf09ecbc>] (destroy_conntrack+0x48/0xd8 [nf_conntrack]) [ 50.220038] [<bf09ecbc>] (destroy_conntrack [nf_conntrack]) from [<c0ac9b58>] (nf_conntrack_destroy+0x94/0x168) [ 50.230160] [<c0ac9b58>] (nf_conntrack_destroy) from [<c0a4aaa0>] (skb_release_head_state+0xa0/0xd0) [ 50.239314] [<c0a4aaa0>] (skb_release_head_state) from [<c0a4aadc>] (skb_release_all+0xc/0x24) [ 50.247946] [<c0a4aadc>] (skb_release_all) from [<c0a4b4cc>] (consume_skb+0x74/0x17c) [ 50.255796] [<c0a4b4cc>] (consume_skb) from [<c081a2dc>] (lan743x_tx_release_desc+0x120/0x124) [ 50.264428] [<c081a2dc>] (lan743x_tx_release_desc) from [<c081a98c>] (lan743x_tx_napi_poll+0x5c/0x18c) [ 50.273755] [<c081a98c>] (lan743x_tx_napi_poll) from [<c0a6b050>] (net_rx_action+0x118/0x4a4) [ 50.282306] [<c0a6b050>] (net_rx_action) from [<c0101364>] (__do_softirq+0x13c/0x53c) [ 50.290157] [<c0101364>] (__do_softirq) from [<c012b29c>] (irq_exit+0x150/0x17c) [ 50.297575] [<c012b29c>] (irq_exit) from [<c0196a08>] (__handle_domain_irq+0x60/0xb0) [ 50.305423] [<c0196a08>] (__handle_domain_irq) from [<c05d44fc>] (gic_handle_irq+0x4c/0x90) [ 50.313790] [<c05d44fc>] (gic_handle_irq) from [<c0100ed4>] (__irq_usr+0x54/0x80) [ 50.321287] Exception stack(0xecd99fb0 to 0xecd99ff8) [ 50.326355] 9fa0: 1cf1aa74 00000001 00000001 00000000 [ 50.334547] 9fc0: 00000001 00000000 00000000 00000000 00000000 00000000 00004097 b6d17d14 [ 50.342738] 9fe0: 00000001 b6d17c60 00000000 b6e71f94 800b0010 ffffffff [ 50.349364] irq event stamp: 2525027 [ 50.352955] hardirqs last enabled at (2525026): [<c0a6afec>] net_rx_action+0xb4/0x4a4 [ 50.360892] hardirqs last disabled at (2525027): [<c0d6d2fc>] _raw_spin_lock_irqsave+0x1c/0x50 [ 50.369517] softirqs last enabled at (2524660): [<c01015b4>] __do_softirq+0x38c/0x53c [ 50.377446] softirqs last disabled at (2524693): [<c012b29c>] irq_exit+0x150/0x17c [ 50.385027] ---[ end trace c0b571db4bc8087d ]--- The driver is calling dev_kfree_skb() from code inside a spinlock, where h/w interrupts are disabled. This is forbidden, as documented in include/linux/netdevice.h. The correct function to use dev_kfree_skb_irq(), or dev_kfree_skb_any(). Fix by using the correct dev_kfree_skb_xxx() functions: in lan743x_tx_release_desc(): called by lan743x_tx_release_completed_descriptors() called by in lan743x_tx_napi_poll() which holds a spinlock called by lan743x_tx_release_all_descriptors() called by lan743x_tx_close() which can-sleep conclusion: use dev_kfree_skb_any() in lan743x_tx_xmit_frame(): which holds a spinlock conclusion: use dev_kfree_skb_irq() in lan743x_tx_close(): which can-sleep conclusion: use dev_kfree_skb() in lan743x_rx_release_ring_element(): called by lan743x_rx_close() which can-sleep called by lan743x_rx_open() which can-sleep conclusion: use dev_kfree_skb() Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com> Link: https://lore.kernel.org/r/20201112185949.11315-1-TheSven73@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 21:32:22 UTC |
| 1ba86d4 | Paul Moore | 13 November 2020, 21:30:40 UTC | netlabel: fix an uninitialized warning in netlbl_unlabel_staticlist() Static checking revealed that a previous fix to netlbl_unlabel_staticlist() leaves a stack variable uninitialized, this patches fixes that. Fixes: 866358ec331f ("netlabel: fix our progress tracking in netlbl_unlabel_staticlist()") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Reviewed-by: James Morris <jamorris@linux.microsoft.com> Link: https://lore.kernel.org/r/160530304068.15651.18355773009751195447.stgit@sifl Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 20:07:57 UTC |
| 057a10f | Xin Long | 14 November 2020, 05:22:53 UTC | sctp: change to hold/put transport for proto_unreach_timer A call trace was found in Hangbin's Codenomicon testing with debug kernel: [ 2615.981988] ODEBUG: free active (active state 0) object type: timer_list hint: sctp_generate_proto_unreach_event+0x0/0x3a0 [sctp] [ 2615.995050] WARNING: CPU: 17 PID: 0 at lib/debugobjects.c:328 debug_print_object+0x199/0x2b0 [ 2616.095934] RIP: 0010:debug_print_object+0x199/0x2b0 [ 2616.191533] Call Trace: [ 2616.194265] <IRQ> [ 2616.202068] debug_check_no_obj_freed+0x25e/0x3f0 [ 2616.207336] slab_free_freelist_hook+0xeb/0x140 [ 2616.220971] kfree+0xd6/0x2c0 [ 2616.224293] rcu_do_batch+0x3bd/0xc70 [ 2616.243096] rcu_core+0x8b9/0xd00 [ 2616.256065] __do_softirq+0x23d/0xacd [ 2616.260166] irq_exit+0x236/0x2a0 [ 2616.263879] smp_apic_timer_interrupt+0x18d/0x620 [ 2616.269138] apic_timer_interrupt+0xf/0x20 [ 2616.273711] </IRQ> This is because it holds asoc when transport->proto_unreach_timer starts and puts asoc when the timer stops, and without holding transport the transport could be freed when the timer is still running. So fix it by holding/putting transport instead for proto_unreach_timer in transport, just like other timers in transport. v1->v2: - Also use sctp_transport_put() for the "out_unlock:" path in sctp_generate_proto_unreach_event(), as Marcelo noticed. Fixes: 50b5d6ad6382 ("sctp: Fix a race between ICMP protocol unreachable and connect()") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Link: https://lore.kernel.org/r/102788809b554958b13b95d33440f5448113b8d6.1605331373.git.lucien.xin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 19:57:12 UTC |
| 65b422d | Stefano Garzarella | 12 November 2020, 13:38:37 UTC | vsock: forward all packets to the host when no H2G is registered Before commit c0cfa2d8a788 ("vsock: add multi-transports support"), if a G2H transport was loaded (e.g. virtio transport), every packets was forwarded to the host, regardless of the destination CID. The H2G transports implemented until then (vhost-vsock, VMCI) always responded with an error, if the destination CID was not VMADDR_CID_HOST. From that commit, we are using the remote CID to decide which transport to use, so packets with remote CID > VMADDR_CID_HOST(2) are sent only through H2G transport. If no H2G is available, packets are discarded directly in the guest. Some use cases (e.g. Nitro Enclaves [1]) rely on the old behaviour to implement sibling VMs communication, so we restore the old behavior when no H2G is registered. It will be up to the host to discard packets if the destination is not the right one. As it was already implemented before adding multi-transport support. Tested with nested QEMU/KVM by me and Nitro Enclaves by Andra. [1] Documentation/virt/ne_overview.rst Cc: Jorgen Hansen <jhansen@vmware.com> Cc: Dexuan Cui <decui@microsoft.com> Fixes: c0cfa2d8a788 ("vsock: add multi-transports support") Reported-by: Andra Paraschiv <andraprs@amazon.com> Tested-by: Andra Paraschiv <andraprs@amazon.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/r/20201112133837.34183-1-sgarzare@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 19:33:39 UTC |
| 9230706 | Tobias Waldekranz | 12 November 2020, 11:43:35 UTC | net: dsa: mv88e6xxx: Avoid VTU corruption on 6097 As soon as you add the second port to a VLAN, all other port membership configuration is overwritten with zeroes. The HW interprets this as all ports being "unmodified members" of the VLAN. In the simple case when all ports belong to the same VLAN, switching will still work. But using multiple VLANs or trying to set multiple ports as tagged members will not work. On the 6352, doing a VTU GetNext op, followed by an STU GetNext op will leave you with both the member- and state- data in the VTU/STU data registers. But on the 6097 (which uses the same implementation), the STU GetNext will override the information gathered from the VTU GetNext. Separate the two stages, parsing the result of the VTU GetNext before doing the STU GetNext. We opt to update the existing implementation for all applicable chips, as opposed to creating a separate callback for 6097, because although the previous implementation did work for (at least) 6352, the datasheet does not mention the masking behavior. Fixes: ef6fcea37f01 ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 19:29:29 UTC |
| 3734471 | Zhang Changzhong | 12 November 2020, 11:23:59 UTC | net: phy: smsc: add missed clk_disable_unprepare in smsc_phy_probe() Add the missing clk_disable_unprepare() before return from smsc_phy_probe() in the error handling case. Fixes: bedd8d78aba3 ("net: phy: smsc: LAN8710/20: add phy refclk in support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/r/1605180239-1792-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 19:21:13 UTC |
| ceb736e | Zhang Qilong | 12 November 2020, 08:09:50 UTC | ipv6: Fix error path to cancel the meseage genlmsg_cancel() needs to be called in the error path of inet6_fill_ifmcaddr and inet6_fill_ifacaddr to cancel the message. Fixes: 6ecf4c37eb3e ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Link: https://lore.kernel.org/r/20201112080950.1476302-1-zhangqilong3@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 02:20:00 UTC |
| 9c2e14b | Yi-Hung Wei | 11 November 2020, 00:16:40 UTC | ip_tunnels: Set tunnel option flag when tunnel metadata is present Currently, we may set the tunnel option flag when the size of metadata is zero. For example, we set TUNNEL_GENEVE_OPT in the receive function no matter the geneve option is present or not. As this may result in issues on the tunnel flags consumers, this patch fixes the issue. Related discussion: * https://lore.kernel.org/netdev/1604448694-19351-1-git-send-email-yihung.wei@gmail.com/T/#u Fixes: 256c87c17c53 ("net: check tunnel option type in tunnel flags") Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com> Link: https://lore.kernel.org/r/1605053800-74072-1-git-send-email-yihung.wei@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 14 November 2020, 00:58:10 UTC |
| 81e329e | Wang Qing | 12 November 2020, 16:45:41 UTC | net: ethernet: ti: am65-cpts: update ret when ptp_clock is ERROR We always have to update the value of ret, otherwise the error value may be the previous one. Fixes: f6bd59526ca5 ("net: ethernet: ti: introduce am654 common platform time sync driver") Signed-off-by: Wang Qing <wangqing@vivo.com> [grygorii.strashko@ti.com: fix build warn, subj add fixes tag] Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/20201112164541.3223-1-grygorii.strashko@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 23:25:43 UTC |
| 8c07205 | Wang Hai | 13 November 2020, 11:32:36 UTC | net: marvell: prestera: fix error return code in prestera_pci_probe() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 4c2703dfd7fa ("net: marvell: prestera: Add PCI interface support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Vadym Kochan <vadym.kochan@plvision.eu> Acked-by: Vadym Kochan <vadym.kochan@plvision.eu> Link: https://lore.kernel.org/r/20201113113236.71678-1-wanghai38@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 23:09:54 UTC |
| aa6306a | Steen Hegelund | 13 November 2020, 09:11:16 UTC | net: phy: mscc: remove non-MACSec compatible phy Selecting VSC8575 as a MACSec PHY was not correct The relevant datasheet can be found here: - VSC8575: https://www.microchip.com/wwwproducts/en/VSC8575 History: v1 -> v2: - Corrected the sha in the "Fixes:" tag Fixes: 1bbe0ecc2a1a ("net: phy: mscc: macsec initialization") Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Reviewed-by: Antoine Tenart <atenart@kernel.org> Link: https://lore.kernel.org/r/20201113091116.1102450-1-steen.hegelund@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 23:08:07 UTC |
| 8cf8821 | Jeff Dike | 13 November 2020, 01:58:15 UTC | net: Exempt multicast addresses from five-second neighbor lifetime Commit 58956317c8de ("neighbor: Improve garbage collection") guarantees neighbour table entries a five-second lifetime. Processes which make heavy use of multicast can fill the neighour table with multicast addresses in five seconds. At that point, neighbour entries can't be GC-ed because they aren't five seconds old yet, the kernel log starts to fill up with "neighbor table overflow!" messages, and sends start to fail. This patch allows multicast addresses to be thrown out before they've lived out their five seconds. This makes room for non-multicast addresses and makes messages to all addresses more reliable in these circumstances. Fixes: 58956317c8de ("neighbor: Improve garbage collection") Signed-off-by: Jeff Dike <jdike@akamai.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20201113015815.31397-1-jdike@akamai.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 22:24:39 UTC |
| 2b56687 | Grygorii Strashko | 12 November 2020, 11:15:46 UTC | net: ethernet: ti: cpsw: fix cpts irq after suspend Depending on the SoC/platform the CPSW can completely lose context after a suspend/resume cycle, including CPSW wrapper (WR) which will cause reset of WR_C0_MISC_EN register, so CPTS IRQ will became disabled. Fix it by moving CPTS IRQ enabling in cpsw_ndo_open() where CPTS is actually started. Fixes: 84ea9c0a95d7 ("net: ethernet: ti: cpsw: enable cpts irq") Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20201112111546.20343-1-grygorii.strashko@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 22:20:42 UTC |
| 1395f8d | Jakub Kicinski | 13 November 2020, 19:58:55 UTC | Merge tag 'mac80211-for-net-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== A handful of fixes: * a use-after-free fix in rfkill * a memory leak fix in the mac80211 TX status path * some rate scaling fixes * a fix for the often-reported (by syzbot) sleeping in atomic issue with mac80211's station removal * tag 'mac80211-for-net-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211: mac80211: free sta in sta_info_insert_finish() on errors mac80211: minstrel: fix tx status processing corner case mac80211: minstrel: remove deferred sampling code mac80211: fix memory leak on filtered powersave frames rfkill: Fix use-after-free in rfkill_resume() ==================== Link: https://lore.kernel.org/r/20201113093421.24025-1-johannes@sipsolutions.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 19:58:55 UTC |
| 7bc40ae | Johannes Berg | 12 November 2020, 10:22:04 UTC | mac80211: free sta in sta_info_insert_finish() on errors If sta_info_insert_finish() fails, we currently keep the station around and free it only in the caller, but there's only one such caller and it always frees it immediately. As syzbot found, another consequence of this split is that we can put things that sleep only into __cleanup_single_sta() and not in sta_info_free(), but this is the only place that requires such of sta_info_free() now. Change this to free the station in sta_info_insert_finish(), in which case we can still sleep. This will also let us unify the cleanup code later. Cc: stable@vger.kernel.org Fixes: dcd479e10a05 ("mac80211: always wind down STA state") Reported-by: syzbot+32c6c38c4812d22f2f0b@syzkaller.appspotmail.com Reported-by: syzbot+4c81fe92e372d26c4246@syzkaller.appspotmail.com Reported-by: syzbot+6a7fe9faf0d1d61bc24a@syzkaller.appspotmail.com Reported-by: syzbot+abed06851c5ffe010921@syzkaller.appspotmail.com Reported-by: syzbot+b7aeb9318541a1c709f1@syzkaller.appspotmail.com Reported-by: syzbot+d5a9416c6cafe53b5dd0@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20201112112201.ee6b397b9453.I9c31d667a0ea2151441cc64ed6613d36c18a48e0@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> | 13 November 2020, 08:48:32 UTC |
| 4ee18c1 | Xie He | 12 November 2020, 10:35:06 UTC | net: x25: Increase refcnt of "struct x25_neigh" in x25_rx_call_request The x25_disconnect function in x25_subr.c would decrease the refcount of "x25->neighbour" (struct x25_neigh) and reset this pointer to NULL. However, the x25_rx_call_request function in af_x25.c, which is called when we receive a connection request, does not increase the refcount when it assigns the pointer. Fix this issue by increasing the refcount of "struct x25_neigh" in x25_rx_call_request. This patch fixes frequent kernel crashes when using AF_X25 sockets. Fixes: 4becb7ee5b3d ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect") Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Link: https://lore.kernel.org/r/20201112103506.5875-1-xie.he.0141@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 02:01:40 UTC |
| baee199 | Zhang Changzhong | 12 November 2020, 11:34:39 UTC | net: ethernet: mtk-star-emac: fix error return code in mtk_star_enable() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 8c7bd5a454ff ("net: ethernet: mtk-star-emac: new driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Link: https://lore.kernel.org/r/1605180879-2573-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 01:58:37 UTC |
| e8aa6d5 | Vincent Stehlé | 12 November 2020, 08:48:33 UTC | net: ethernet: mtk-star-emac: return ok when xmit drops The ndo_start_xmit() method must return NETDEV_TX_OK if the DMA mapping fails, after freeing the socket buffer. Fix the mtk_star_netdev_start_xmit() function accordingly. Fixes: 8c7bd5a454ff ("net: ethernet: mtk-star-emac: new driver") Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Link: https://lore.kernel.org/r/20201112084833.21842-1-vincent.stehle@laposte.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 01:05:15 UTC |
| 1922a46 | Joel Stanley | 12 November 2020, 06:12:10 UTC | net/ncsi: Fix netlink registration If a user unbinds and re-binds a NC-SI aware driver the kernel will attempt to register the netlink interface at runtime. The structure is marked __ro_after_init so registration fails spectacularly at this point. # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/bind ftgmac100 1e660000.ethernet: Read MAC address 52:54:00:12:34:56 from chip ftgmac100 1e660000.ethernet: Using NCSI interface 8<--- cut here --- Unable to handle kernel paging request at virtual address 80a8f858 pgd = 8c768dd6 [80a8f858] *pgd=80a0841e(bad) Internal error: Oops: 80d [#1] SMP ARM CPU: 0 PID: 116 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00003-gdd25b227ec1e #51 Hardware name: Generic DT based system PC is at genl_register_family+0x1f8/0x6d4 LR is at 0xff26ffff pc : [<8073f930>] lr : [<ff26ffff>] psr: 20000153 sp : 8553bc80 ip : 81406244 fp : 8553bd04 r10: 8085d12c r9 : 80a8f73c r8 : 85739000 r7 : 00000017 r6 : 80a8f860 r5 : 80c8ab98 r4 : 80a8f858 r3 : 00000000 r2 : 00000000 r1 : 81406130 r0 : 00000017 Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none Control: 00c5387d Table: 85524008 DAC: 00000051 Process sh (pid: 116, stack limit = 0x1f1988d6) ... Backtrace: [<8073f738>] (genl_register_family) from [<80860ac0>] (ncsi_init_netlink+0x20/0x48) r10:8085d12c r9:80c8fb0c r8:85739000 r7:00000000 r6:81218000 r5:85739000 r4:8121c000 [<80860aa0>] (ncsi_init_netlink) from [<8085d740>] (ncsi_register_dev+0x1b0/0x210) r5:8121c400 r4:8121c000 [<8085d590>] (ncsi_register_dev) from [<805a8060>] (ftgmac100_probe+0x6e0/0x778) r10:00000004 r9:80950228 r8:8115bc10 r7:8115ab00 r6:9eae2c24 r5:813b6f88 r4:85739000 [<805a7980>] (ftgmac100_probe) from [<805355ec>] (platform_drv_probe+0x58/0xa8) r9:80c76bb0 r8:00000000 r7:80cd4974 r6:80c76bb0 r5:8115bc10 r4:00000000 [<80535594>] (platform_drv_probe) from [<80532d58>] (really_probe+0x204/0x514) r7:80cd4974 r6:00000000 r5:80cd4868 r4:8115bc10 Jakub pointed out that ncsi_register_dev is obviously broken, because there is only one family so it would never work if there was more than one ncsi netdev. Fix the crash by registering the netlink family once on boot, and drop the code to unregister it. Fixes: 955dc68cb9b2 ("net/ncsi: Add generic netlink family") Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Link: https://lore.kernel.org/r/20201112061210.914621-1-joel@jms.id.au Signed-off-by: Jakub Kicinski <kuba@kernel.org> | 13 November 2020, 01:00:13 UTC |
| db7c953 | Linus Torvalds | 12 November 2020, 22:02:04 UTC | Merge tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Current release - regressions: - arm64: dts: fsl-ls1028a-kontron-sl28: specify in-band mode for ENETC Current release - bugs in new features: - mptcp: provide rmem[0] limit offset to fix oops Previous release - regressions: - IPv6: Set SIT tunnel hard_header_len to zero to fix path MTU calculations - lan743x: correctly handle chips with internal PHY - bpf: Don't rely on GCC __attribute__((optimize)) to disable GCSE - mlx5e: Fix VXLAN port table synchronization after function reload Previous release - always broken: - bpf: Zero-fill re-used per-cpu map element - fix out-of-order UDP packets when forwarding with UDP GSO fraglists turned on: - fix UDP header access on Fast/frag0 UDP GRO - fix IP header access and skb lookup on Fast/frag0 UDP GRO - ethtool: netlink: add missing netdev_features_change() call - net: Update window_clamp if SOCK_RCVBUF is set - igc: Fix returning wrong statistics - ch_ktls: fix multiple leaks and corner cases in Chelsio TLS offload - tunnels: Fix off-by-one in lower MTU bounds for ICMP/ICMPv6 replies - r8169: disable hw csum for short packets on all chip versions - vrf: Fix fast path output packet handling with async Netfilter rules" * tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits) lan743x: fix use of uninitialized variable net: udp: fix IP header access and skb lookup on Fast/frag0 UDP GRO net: udp: fix UDP header access on Fast/frag0 UDP GRO devlink: Avoid overwriting port attributes of registered port vrf: Fix fast path output packet handling with async Netfilter rules cosa: Add missing kfree in error path of cosa_write net: switch to the kernel.org patchwork instance ch_ktls: stop the txq if reaches threshold ch_ktls: tcb update fails sometimes ch_ktls/cxgb4: handle partial tag alone SKBs ch_ktls: don't free skb before sending FIN ch_ktls: packet handling prior to start marker ch_ktls: Correction in middle record handling ch_ktls: missing handling of header alone ch_ktls: Correction in trimmed_len calculation cxgb4/ch_ktls: creating skbs causes panic ch_ktls: Update cheksum information ch_ktls: Correction in finding correct length cxgb4/ch_ktls: decrypted bit is not enough net/x25: Fix null-ptr-deref in x25_connect ... | 12 November 2020, 22:02:04 UTC |
| 200f9d2 | Linus Torvalds | 12 November 2020, 21:49:12 UTC | Merge tag 'nfs-for-5.10-2' of git://git.linux-nfs.org/projects/anna/linux-nfs Pull NFS client bugfixes from Anna Schumaker: "Stable fixes: - Fix failure to unregister shrinker Other fixes: - Fix unnecessary locking to clear up some contention - Fix listxattr receive buffer size - Fix default mount options for nfsroot" * tag 'nfs-for-5.10-2' of git://git.linux-nfs.org/projects/anna/linux-nfs: NFS: Remove unnecessary inode lock in nfs_fsync_dir() NFS: Remove unnecessary inode locking in nfs_llseek_dir() NFS: Fix listxattr receive buffer size NFSv4.2: fix failure to unregister shrinker nfsroot: Default mount option should ask for built-in NFS version | 12 November 2020, 21:49:12 UTC |
