Revision 3ef4572110a43acdd7d401b0cb184c6ebd6eaa17 authored by Tom Rini on 28 June 2021, 19:38:55 UTC, committed by Tom Rini on 28 June 2021, 19:38:55 UTC
Signed-off-by: Tom Rini <trini@konsulko.com>
1 parent 534f0fb
vme8349.h
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* esd vme8349 U-Boot configuration file
* Copyright (c) 2008, 2009 esd gmbh Hannover Germany
*
* (C) Copyright 2006-2010
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* reinhard.arlt@esd-electronics.de
* Based on the MPC8349EMDS config.
*/
/*
* vme8349 board configuration file.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
/*
* DDR Setup
*/
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
#define CONFIG_SPD_EEPROM
#define SPD_EEPROM_ADDRESS 0x54
#define CONFIG_SYS_READ_SPD vme8349_read_spd
#define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */
/*
* 32-bit data path mode.
*
* Please note that using this mode for devices with the real density of 64-bit
* effectively reduces the amount of available memory due to the effect of
* wrapping around while translating address to row/columns, for example in the
* 256MB module the upper 128MB get aliased with contents of the lower
* 128MB); normally this define should be used for devices with real 32-bit
* data path.
*/
#undef CONFIG_DDR_32BIT
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is sys memory*/
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
#define CONFIG_DDR_2T_TIMING
#define CONFIG_SYS_DDRCDR (DDRCDR_DHC_EN \
| DDRCDR_ODT \
| DDRCDR_Q_DRN)
/* 0x80080001 */
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */
#define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */
#define CONFIG_SYS_WINDOW1_BASE 0xf0000000
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xF7000000 /* Initial RAM addr */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* size */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */
#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */
#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
/*
* Serial Port
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
#define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */
/* TSEC */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xFIXME
#define PCI_ENET0_MEMADDR 0xFIXME
#define PCI_IDSEL_NUMBER 0xFIXME
#endif
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
/*
* TSEC configuration
*/
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_GMII /* MII PHY management */
#define CONFIG_TSEC1
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2
#define CONFIG_TSEC2_NAME "TSEC1"
#define CONFIG_PHY_M88E1111
#define TSEC1_PHY_ADDR 0x08
#define TSEC2_PHY_ADDR 0x10
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */
/*
* Environment
*/
#ifndef CONFIG_SYS_RAMBOOT
/* Address and size of Redundant Environment Sector */
#endif
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_SYS_RTC_BUS_NUM 0x01
#define CONFIG_SYS_I2C_RTC_ADDR 0x32
/* Pass Ethernet MAC to VxWorks */
#define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/
#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
/* System IO Config */
#define CONFIG_SYS_SICRH 0
#define CONFIG_SYS_SICRL SICRL_LDP_A
#define CONFIG_SYS_GPIO1_PRELIM
#define CONFIG_SYS_GPIO1_DIR 0x00100000
#define CONFIG_SYS_GPIO1_DAT 0x00100000
#define CONFIG_SYS_GPIO2_PRELIM
#define CONFIG_SYS_GPIO2_DIR 0x78900000
#define CONFIG_SYS_GPIO2_DAT 0x70100000
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#endif
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#endif
/*
* Environment Configuration
*/
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif
#define CONFIG_HOSTNAME "VME8349"
#define CONFIG_ROOTPATH "/tftpboot/rootfs"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=vme8349\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0" \
"update=protect off fff00000 fff3ffff; " \
"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
"upd=run load update\0" \
"fdtaddr=780000\0" \
"fdtfile=vme8349.dtb\0" \
""
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
"$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND "run flash_self"
#ifndef __ASSEMBLY__
int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
unsigned char *buffer, int len);
#endif
#endif /* __CONFIG_H */
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...