Revision 40509ca982c00c4b70fc00be887509feca0bff15 authored by Johan Hovold on 19 March 2013, 08:21:22 UTC, committed by Greg Kroah-Hartman on 21 March 2013, 22:59:05 UTC
Use the port wait queue and make sure to check the serial disconnected flag before accessing private port data after waking up. This is is needed as the private port data (including the wait queue itself) can be gone when waking up after a disconnect. Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1 parent 8edfdab
lp3971.c
/*
* Regulator driver for National Semiconductors LP3971 PMIC chip
*
* Copyright (C) 2009 Samsung Electronics
* Author: Marek Szyprowski <m.szyprowski@samsung.com>
*
* Based on wm8350.c
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <linux/bug.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/lp3971.h>
#include <linux/slab.h>
struct lp3971 {
struct device *dev;
struct mutex io_lock;
struct i2c_client *i2c;
int num_regulators;
struct regulator_dev **rdev;
};
static u8 lp3971_reg_read(struct lp3971 *lp3971, u8 reg);
static int lp3971_set_bits(struct lp3971 *lp3971, u8 reg, u16 mask, u16 val);
#define LP3971_SYS_CONTROL1_REG 0x07
/* System control register 1 initial value,
bits 4 and 5 are EPROM programmable */
#define SYS_CONTROL1_INIT_VAL 0x40
#define SYS_CONTROL1_INIT_MASK 0xCF
#define LP3971_BUCK_VOL_ENABLE_REG 0x10
#define LP3971_BUCK_VOL_CHANGE_REG 0x20
/* Voltage control registers shift:
LP3971_BUCK1 -> 0
LP3971_BUCK2 -> 4
LP3971_BUCK3 -> 6
*/
#define BUCK_VOL_CHANGE_SHIFT(x) (((!!x) << 2) | (x & ~0x01))
#define BUCK_VOL_CHANGE_FLAG_GO 0x01
#define BUCK_VOL_CHANGE_FLAG_TARGET 0x02
#define BUCK_VOL_CHANGE_FLAG_MASK 0x03
#define LP3971_BUCK1_BASE 0x23
#define LP3971_BUCK2_BASE 0x29
#define LP3971_BUCK3_BASE 0x32
static const int buck_base_addr[] = {
LP3971_BUCK1_BASE,
LP3971_BUCK2_BASE,
LP3971_BUCK3_BASE,
};
#define LP3971_BUCK_TARGET_VOL1_REG(x) (buck_base_addr[x])
#define LP3971_BUCK_TARGET_VOL2_REG(x) (buck_base_addr[x]+1)
static const unsigned int buck_voltage_map[] = {
0, 800000, 850000, 900000, 950000, 1000000, 1050000, 1100000,
1150000, 1200000, 1250000, 1300000, 1350000, 1400000, 1450000, 1500000,
1550000, 1600000, 1650000, 1700000, 1800000, 1900000, 2500000, 2800000,
3000000, 3300000,
};
#define BUCK_TARGET_VOL_MASK 0x3f
#define LP3971_BUCK_RAMP_REG(x) (buck_base_addr[x]+2)
#define LP3971_LDO_ENABLE_REG 0x12
#define LP3971_LDO_VOL_CONTR_BASE 0x39
/* Voltage control registers:
LP3971_LDO1 -> LP3971_LDO_VOL_CONTR_BASE + 0
LP3971_LDO2 -> LP3971_LDO_VOL_CONTR_BASE + 0
LP3971_LDO3 -> LP3971_LDO_VOL_CONTR_BASE + 1
LP3971_LDO4 -> LP3971_LDO_VOL_CONTR_BASE + 1
LP3971_LDO5 -> LP3971_LDO_VOL_CONTR_BASE + 2
*/
#define LP3971_LDO_VOL_CONTR_REG(x) (LP3971_LDO_VOL_CONTR_BASE + (x >> 1))
/* Voltage control registers shift:
LP3971_LDO1 -> 0, LP3971_LDO2 -> 4
LP3971_LDO3 -> 0, LP3971_LDO4 -> 4
LP3971_LDO5 -> 0
*/
#define LDO_VOL_CONTR_SHIFT(x) ((x & 1) << 2)
#define LDO_VOL_CONTR_MASK 0x0f
static const unsigned int ldo45_voltage_map[] = {
1000000, 1050000, 1100000, 1150000, 1200000, 1250000, 1300000, 1350000,
1400000, 1500000, 1800000, 1900000, 2500000, 2800000, 3000000, 3300000,
};
static const unsigned int ldo123_voltage_map[] = {
1800000, 1900000, 2000000, 2100000, 2200000, 2300000, 2400000, 2500000,
2600000, 2700000, 2800000, 2900000, 3000000, 3100000, 3200000, 3300000,
};
#define LDO_VOL_MIN_IDX 0x00
#define LDO_VOL_MAX_IDX 0x0f
static int lp3971_ldo_is_enabled(struct regulator_dev *dev)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int ldo = rdev_get_id(dev) - LP3971_LDO1;
u16 mask = 1 << (1 + ldo);
u16 val;
val = lp3971_reg_read(lp3971, LP3971_LDO_ENABLE_REG);
return (val & mask) != 0;
}
static int lp3971_ldo_enable(struct regulator_dev *dev)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int ldo = rdev_get_id(dev) - LP3971_LDO1;
u16 mask = 1 << (1 + ldo);
return lp3971_set_bits(lp3971, LP3971_LDO_ENABLE_REG, mask, mask);
}
static int lp3971_ldo_disable(struct regulator_dev *dev)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int ldo = rdev_get_id(dev) - LP3971_LDO1;
u16 mask = 1 << (1 + ldo);
return lp3971_set_bits(lp3971, LP3971_LDO_ENABLE_REG, mask, 0);
}
static int lp3971_ldo_get_voltage_sel(struct regulator_dev *dev)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int ldo = rdev_get_id(dev) - LP3971_LDO1;
u16 val, reg;
reg = lp3971_reg_read(lp3971, LP3971_LDO_VOL_CONTR_REG(ldo));
val = (reg >> LDO_VOL_CONTR_SHIFT(ldo)) & LDO_VOL_CONTR_MASK;
return val;
}
static int lp3971_ldo_set_voltage_sel(struct regulator_dev *dev,
unsigned int selector)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int ldo = rdev_get_id(dev) - LP3971_LDO1;
return lp3971_set_bits(lp3971, LP3971_LDO_VOL_CONTR_REG(ldo),
LDO_VOL_CONTR_MASK << LDO_VOL_CONTR_SHIFT(ldo),
selector << LDO_VOL_CONTR_SHIFT(ldo));
}
static struct regulator_ops lp3971_ldo_ops = {
.list_voltage = regulator_list_voltage_table,
.is_enabled = lp3971_ldo_is_enabled,
.enable = lp3971_ldo_enable,
.disable = lp3971_ldo_disable,
.get_voltage_sel = lp3971_ldo_get_voltage_sel,
.set_voltage_sel = lp3971_ldo_set_voltage_sel,
};
static int lp3971_dcdc_is_enabled(struct regulator_dev *dev)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int buck = rdev_get_id(dev) - LP3971_DCDC1;
u16 mask = 1 << (buck * 2);
u16 val;
val = lp3971_reg_read(lp3971, LP3971_BUCK_VOL_ENABLE_REG);
return (val & mask) != 0;
}
static int lp3971_dcdc_enable(struct regulator_dev *dev)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int buck = rdev_get_id(dev) - LP3971_DCDC1;
u16 mask = 1 << (buck * 2);
return lp3971_set_bits(lp3971, LP3971_BUCK_VOL_ENABLE_REG, mask, mask);
}
static int lp3971_dcdc_disable(struct regulator_dev *dev)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int buck = rdev_get_id(dev) - LP3971_DCDC1;
u16 mask = 1 << (buck * 2);
return lp3971_set_bits(lp3971, LP3971_BUCK_VOL_ENABLE_REG, mask, 0);
}
static int lp3971_dcdc_get_voltage_sel(struct regulator_dev *dev)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int buck = rdev_get_id(dev) - LP3971_DCDC1;
u16 reg;
reg = lp3971_reg_read(lp3971, LP3971_BUCK_TARGET_VOL1_REG(buck));
reg &= BUCK_TARGET_VOL_MASK;
return reg;
}
static int lp3971_dcdc_set_voltage_sel(struct regulator_dev *dev,
unsigned int selector)
{
struct lp3971 *lp3971 = rdev_get_drvdata(dev);
int buck = rdev_get_id(dev) - LP3971_DCDC1;
int ret;
ret = lp3971_set_bits(lp3971, LP3971_BUCK_TARGET_VOL1_REG(buck),
BUCK_TARGET_VOL_MASK, selector);
if (ret)
return ret;
ret = lp3971_set_bits(lp3971, LP3971_BUCK_VOL_CHANGE_REG,
BUCK_VOL_CHANGE_FLAG_MASK << BUCK_VOL_CHANGE_SHIFT(buck),
BUCK_VOL_CHANGE_FLAG_GO << BUCK_VOL_CHANGE_SHIFT(buck));
if (ret)
return ret;
return lp3971_set_bits(lp3971, LP3971_BUCK_VOL_CHANGE_REG,
BUCK_VOL_CHANGE_FLAG_MASK << BUCK_VOL_CHANGE_SHIFT(buck),
0 << BUCK_VOL_CHANGE_SHIFT(buck));
}
static struct regulator_ops lp3971_dcdc_ops = {
.list_voltage = regulator_list_voltage_table,
.is_enabled = lp3971_dcdc_is_enabled,
.enable = lp3971_dcdc_enable,
.disable = lp3971_dcdc_disable,
.get_voltage_sel = lp3971_dcdc_get_voltage_sel,
.set_voltage_sel = lp3971_dcdc_set_voltage_sel,
};
static const struct regulator_desc regulators[] = {
{
.name = "LDO1",
.id = LP3971_LDO1,
.ops = &lp3971_ldo_ops,
.n_voltages = ARRAY_SIZE(ldo123_voltage_map),
.volt_table = ldo123_voltage_map,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
},
{
.name = "LDO2",
.id = LP3971_LDO2,
.ops = &lp3971_ldo_ops,
.n_voltages = ARRAY_SIZE(ldo123_voltage_map),
.volt_table = ldo123_voltage_map,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
},
{
.name = "LDO3",
.id = LP3971_LDO3,
.ops = &lp3971_ldo_ops,
.n_voltages = ARRAY_SIZE(ldo123_voltage_map),
.volt_table = ldo123_voltage_map,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
},
{
.name = "LDO4",
.id = LP3971_LDO4,
.ops = &lp3971_ldo_ops,
.n_voltages = ARRAY_SIZE(ldo45_voltage_map),
.volt_table = ldo45_voltage_map,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
},
{
.name = "LDO5",
.id = LP3971_LDO5,
.ops = &lp3971_ldo_ops,
.n_voltages = ARRAY_SIZE(ldo45_voltage_map),
.volt_table = ldo45_voltage_map,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
},
{
.name = "DCDC1",
.id = LP3971_DCDC1,
.ops = &lp3971_dcdc_ops,
.n_voltages = ARRAY_SIZE(buck_voltage_map),
.volt_table = buck_voltage_map,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
},
{
.name = "DCDC2",
.id = LP3971_DCDC2,
.ops = &lp3971_dcdc_ops,
.n_voltages = ARRAY_SIZE(buck_voltage_map),
.volt_table = buck_voltage_map,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
},
{
.name = "DCDC3",
.id = LP3971_DCDC3,
.ops = &lp3971_dcdc_ops,
.n_voltages = ARRAY_SIZE(buck_voltage_map),
.volt_table = buck_voltage_map,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
},
};
static int lp3971_i2c_read(struct i2c_client *i2c, char reg, int count,
u16 *dest)
{
int ret;
if (count != 1)
return -EIO;
ret = i2c_smbus_read_byte_data(i2c, reg);
if (ret < 0)
return -EIO;
*dest = ret;
return 0;
}
static int lp3971_i2c_write(struct i2c_client *i2c, char reg, int count,
const u16 *src)
{
if (count != 1)
return -EIO;
return i2c_smbus_write_byte_data(i2c, reg, *src);
}
static u8 lp3971_reg_read(struct lp3971 *lp3971, u8 reg)
{
u16 val = 0;
mutex_lock(&lp3971->io_lock);
lp3971_i2c_read(lp3971->i2c, reg, 1, &val);
dev_dbg(lp3971->dev, "reg read 0x%02x -> 0x%02x\n", (int)reg,
(unsigned)val&0xff);
mutex_unlock(&lp3971->io_lock);
return val & 0xff;
}
static int lp3971_set_bits(struct lp3971 *lp3971, u8 reg, u16 mask, u16 val)
{
u16 tmp;
int ret;
mutex_lock(&lp3971->io_lock);
ret = lp3971_i2c_read(lp3971->i2c, reg, 1, &tmp);
tmp = (tmp & ~mask) | val;
if (ret == 0) {
ret = lp3971_i2c_write(lp3971->i2c, reg, 1, &tmp);
dev_dbg(lp3971->dev, "reg write 0x%02x -> 0x%02x\n", (int)reg,
(unsigned)val&0xff);
}
mutex_unlock(&lp3971->io_lock);
return ret;
}
static int setup_regulators(struct lp3971 *lp3971,
struct lp3971_platform_data *pdata)
{
int i, err;
lp3971->num_regulators = pdata->num_regulators;
lp3971->rdev = kcalloc(pdata->num_regulators,
sizeof(struct regulator_dev *), GFP_KERNEL);
if (!lp3971->rdev) {
err = -ENOMEM;
goto err_nomem;
}
/* Instantiate the regulators */
for (i = 0; i < pdata->num_regulators; i++) {
struct regulator_config config = { };
struct lp3971_regulator_subdev *reg = &pdata->regulators[i];
config.dev = lp3971->dev;
config.init_data = reg->initdata;
config.driver_data = lp3971;
lp3971->rdev[i] = regulator_register(®ulators[reg->id],
&config);
if (IS_ERR(lp3971->rdev[i])) {
err = PTR_ERR(lp3971->rdev[i]);
dev_err(lp3971->dev, "regulator init failed: %d\n",
err);
goto error;
}
}
return 0;
error:
while (--i >= 0)
regulator_unregister(lp3971->rdev[i]);
kfree(lp3971->rdev);
lp3971->rdev = NULL;
err_nomem:
return err;
}
static int lp3971_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
struct lp3971 *lp3971;
struct lp3971_platform_data *pdata = i2c->dev.platform_data;
int ret;
u16 val;
if (!pdata) {
dev_dbg(&i2c->dev, "No platform init data supplied\n");
return -ENODEV;
}
lp3971 = kzalloc(sizeof(struct lp3971), GFP_KERNEL);
if (lp3971 == NULL)
return -ENOMEM;
lp3971->i2c = i2c;
lp3971->dev = &i2c->dev;
mutex_init(&lp3971->io_lock);
/* Detect LP3971 */
ret = lp3971_i2c_read(i2c, LP3971_SYS_CONTROL1_REG, 1, &val);
if (ret == 0 && (val & SYS_CONTROL1_INIT_MASK) != SYS_CONTROL1_INIT_VAL)
ret = -ENODEV;
if (ret < 0) {
dev_err(&i2c->dev, "failed to detect device\n");
goto err_detect;
}
ret = setup_regulators(lp3971, pdata);
if (ret < 0)
goto err_detect;
i2c_set_clientdata(i2c, lp3971);
return 0;
err_detect:
kfree(lp3971);
return ret;
}
static int lp3971_i2c_remove(struct i2c_client *i2c)
{
struct lp3971 *lp3971 = i2c_get_clientdata(i2c);
int i;
for (i = 0; i < lp3971->num_regulators; i++)
regulator_unregister(lp3971->rdev[i]);
kfree(lp3971->rdev);
kfree(lp3971);
return 0;
}
static const struct i2c_device_id lp3971_i2c_id[] = {
{ "lp3971", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, lp3971_i2c_id);
static struct i2c_driver lp3971_i2c_driver = {
.driver = {
.name = "LP3971",
.owner = THIS_MODULE,
},
.probe = lp3971_i2c_probe,
.remove = lp3971_i2c_remove,
.id_table = lp3971_i2c_id,
};
module_i2c_driver(lp3971_i2c_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Marek Szyprowski <m.szyprowski@samsung.com>");
MODULE_DESCRIPTION("LP3971 PMIC driver");
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...