Revision 474095e46cd14421821da3201a9fd6a4c070996b authored by Linus Torvalds on 24 April 2015, 16:28:01 UTC, committed by Linus Torvalds on 24 April 2015, 16:28:01 UTC
Pull md updates from Neil Brown:
"More updates that usual this time. A few have performance impacts
which hould mostly be positive, but RAID5 (in particular) can be very
work-load ensitive... We'll have to wait and see.
Highlights:
- "experimental" code for managing md/raid1 across a cluster using
DLM. Code is not ready for general use and triggers a WARNING if
used. However it is looking good and mostly done and having in
mainline will help co-ordinate development.
- RAID5/6 can now batch multiple (4K wide) stripe_heads so as to
handle a full (chunk wide) stripe as a single unit.
- RAID6 can now perform read-modify-write cycles which should help
performance on larger arrays: 6 or more devices.
- RAID5/6 stripe cache now grows and shrinks dynamically. The value
set is used as a minimum.
- Resync is now allowed to go a little faster than the 'mininum' when
there is competing IO. How much faster depends on the speed of the
devices, so the effective minimum should scale with device speed to
some extent"
* tag 'md/4.1' of git://neil.brown.name/md: (58 commits)
md/raid5: don't do chunk aligned read on degraded array.
md/raid5: allow the stripe_cache to grow and shrink.
md/raid5: change ->inactive_blocked to a bit-flag.
md/raid5: move max_nr_stripes management into grow_one_stripe and drop_one_stripe
md/raid5: pass gfp_t arg to grow_one_stripe()
md/raid5: introduce configuration option rmw_level
md/raid5: activate raid6 rmw feature
md/raid6 algorithms: xor_syndrome() for SSE2
md/raid6 algorithms: xor_syndrome() for generic int
md/raid6 algorithms: improve test program
md/raid6 algorithms: delta syndrome functions
raid5: handle expansion/resync case with stripe batching
raid5: handle io error of batch list
RAID5: batch adjacent full stripe write
raid5: track overwrite disk count
raid5: add a new flag to track if a stripe can be batched
raid5: use flex_array for scribble data
md raid0: access mddev->queue (request queue member) conditionally because it is not set when accessed from dm-raid
md: allow resync to go faster when there is competing IO.
md: remove 'go_faster' option from ->sync_request()
...
smsc_ece1099.txt
What is smsc-ece1099?
----------------------
The ECE1099 is a 40-Pin 3.3V Keyboard Scan Expansion
or GPIO Expansion device. The device supports a keyboard
scan matrix of 23x8. The device is connected to a Master
via the SMSC BC-Link interface or via the SMBus.
Keypad scan Input(KSI) and Keypad Scan Output(KSO) signals
are multiplexed with GPIOs.
Interrupt generation
--------------------
Interrupts can be generated by an edge detection on a GPIO
pin or an edge detection on one of the bus interface pins.
Interrupts can also be detected on the keyboard scan interface.
The bus interrupt pin (BC_INT# or SMBUS_INT#) is asserted if
any bit in one of the Interrupt Status registers is 1 and
the corresponding Interrupt Mask bit is also 1.
In order for software to determine which device is the source
of an interrupt, it should first read the Group Interrupt Status Register
to determine which Status register group is a source for the interrupt.
Software should read both the Status register and the associated Mask register,
then AND the two values together. Bits that are 1 in the result of the AND
are active interrupts. Software clears an interrupt by writing a 1 to the
corresponding bit in the Status register.
Communication Protocol
----------------------
- SMbus slave Interface
The host processor communicates with the ECE1099 device
through a series of read/write registers via the SMBus
interface. SMBus is a serial communication protocol between
a computer host and its peripheral devices. The SMBus data
rate is 10KHz minimum to 400 KHz maximum
- Slave Bus Interface
The ECE1099 device SMBus implementation is a subset of the
SMBus interface to the host. The device is a slave-only SMBus device.
The implementation in the device is a subset of SMBus since it
only supports four protocols.
The Write Byte, Read Byte, Send Byte, and Receive Byte protocols are the
only valid SMBus protocols for the device.
- BC-LinkTM Interface
The BC-Link is a proprietary bus that allows communication
between a Master device and a Companion device. The Master
device uses this serial bus to read and write registers
located on the Companion device. The bus comprises three signals,
BC_CLK, BC_DAT and BC_INT#. The Master device always provides the
clock, BC_CLK, and the Companion device is the source for an
independent asynchronous interrupt signal, BC_INT#. The ECE1099
supports BC-Link speeds up to 24MHz.
Computing file changes ...
