Skip to main content

Browse the archive

Revision 5885b9b3f030f9b430f6b1c7fa396c885033f2f8 authored by Linus Torvalds on 16 December 2011, 19:14:42 UTC, committed by Linus Torvalds on 16 December 2011, 19:14:42 UTC 
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
 
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: HDA: Use LPIB Position fix for Intel SCH Poulsbo
  ALSA: hda: fix mute led polarity for HP laptops with buggy BIOS
  ALSA: HDA: Set position fix to LPIB for an Atom/Poulsbo based device
  ASoC: Fix hx4700 error handling to free gpios if snd_soc_register_card fails
  ASoC: WM8958: correctly show firmware magic on mismatch
  ASoC: mxs: Add appropriate MODULE_ALIAS()
  ASoC: mxs: Add missing MODULE_LICENSE("GPL")
  ASoC: Fix WM8996 24.576MHz clock operation
  ASoC: Include linux/module.h for smdk2443_wm9710
  ASoC: Fix a typo in jive_wm8750
  ASoC: Fix build dependency for SND_SOC_JZ4740_CODEC
  ASoC: Include linux/io.h for jz4740 codec
2 parent s 1c5ff0f + 844ec31
Raw File
dmfe.txt 
Note: This driver doesn't have a maintainer.

Davicom DM9102(A)/DM9132/DM9801 fast ethernet driver for Linux.

This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General   Public License
as published by the Free Software Foundation; either version 2
of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
GNU General Public License for more details.


This driver provides kernel support for Davicom DM9102(A)/DM9132/DM9801 ethernet cards ( CNET
10/100 ethernet cards uses Davicom chipset too, so this driver supports CNET cards too ).If you
didn't compile this driver as a module, it will automatically load itself on boot and print a
line similar to :

	dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)

If you compiled this driver as a module, you have to load it on boot.You can load it with command :

	insmod dmfe

This way it will autodetect the device mode.This is the suggested way to load the module.Or you can pass
a mode= setting to module while loading, like :

	insmod dmfe mode=0 # Force 10M Half Duplex
	insmod dmfe mode=1 # Force 100M Half Duplex
	insmod dmfe mode=4 # Force 10M Full Duplex
	insmod dmfe mode=5 # Force 100M Full Duplex

Next you should configure your network interface with a command similar to :

	ifconfig eth0 172.22.3.18
                      ^^^^^^^^^^^
		     Your IP Address

Then you may have to modify the default routing table with command :

	route add default eth0


Now your ethernet card should be up and running.


TODO:

Implement pci_driver::suspend() and pci_driver::resume() power management methods.
Check on 64 bit boxes.
Check and fix on big endian boxes.
Test and make sure PCI latency is now correct for all cases.


Authors:

Sten Wang <sten_wang@davicom.com.tw >   : Original Author

Contributors:

Marcelo Tosatti <marcelo@conectiva.com.br>
Alan Cox <alan@lxorguk.ukuu.org.uk>
Jeff Garzik <jgarzik@pobox.com>
Vojtech Pavlik <vojtech@suse.cz>
back to top