Revision 6065fd0d179b96ddc488c76542349bcb148a95fd authored by Yuchung Cheng on 07 December 2017, 19:33:33 UTC, committed by David S. Miller on 08 December 2017, 19:14:11 UTC
RACK skips an ACK unless it advances the most recently delivered TX timestamp (rack.mstamp). Since RACK also uses the most recent RTT to decide if a packet is lost, RACK should still run the loss detection whenever the most recent RTT changes. For example, an ACK that does not advance the timestamp but triggers the cwnd undo due to reordering, would then use the most recent (higher) RTT measurement to detect further losses. Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Priyaranjan Jha <priyarjha@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1 parent 428aec5
btmrvl.txt
=============
btmrvl driver
=============
All commands are used via debugfs interface.
Set/get driver configurations
=============================
Path: /debug/btmrvl/config/
gpiogap=[n], hscfgcmd
These commands are used to configure the host sleep parameters::
bit 8:0 -- Gap
bit 16:8 -- GPIO
where GPIO is the pin number of GPIO used to wake up the host.
It could be any valid GPIO pin# (e.g. 0-7) or 0xff (SDIO interface
wakeup will be used instead).
where Gap is the gap in milli seconds between wakeup signal and
wakeup event, or 0xff for special host sleep setting.
Usage::
# Use SDIO interface to wake up the host and set GAP to 0x80:
echo 0xff80 > /debug/btmrvl/config/gpiogap
echo 1 > /debug/btmrvl/config/hscfgcmd
# Use GPIO pin #3 to wake up the host and set GAP to 0xff:
echo 0x03ff > /debug/btmrvl/config/gpiogap
echo 1 > /debug/btmrvl/config/hscfgcmd
psmode=[n], pscmd
These commands are used to enable/disable auto sleep mode
where the option is::
1 -- Enable auto sleep mode
0 -- Disable auto sleep mode
Usage::
# Enable auto sleep mode
echo 1 > /debug/btmrvl/config/psmode
echo 1 > /debug/btmrvl/config/pscmd
# Disable auto sleep mode
echo 0 > /debug/btmrvl/config/psmode
echo 1 > /debug/btmrvl/config/pscmd
hsmode=[n], hscmd
These commands are used to enable host sleep or wake up firmware
where the option is::
1 -- Enable host sleep
0 -- Wake up firmware
Usage::
# Enable host sleep
echo 1 > /debug/btmrvl/config/hsmode
echo 1 > /debug/btmrvl/config/hscmd
# Wake up firmware
echo 0 > /debug/btmrvl/config/hsmode
echo 1 > /debug/btmrvl/config/hscmd
Get driver status
=================
Path: /debug/btmrvl/status/
Usage::
cat /debug/btmrvl/status/<args>
where the args are:
curpsmode
This command displays current auto sleep status.
psstate
This command display the power save state.
hsstate
This command display the host sleep state.
txdnldrdy
This command displays the value of Tx download ready flag.
Issuing a raw hci command
=========================
Use hcitool to issue raw hci command, refer to hcitool manual
Usage::
Hcitool cmd <ogf> <ocf> [Parameters]
Interface Control Command::
hcitool cmd 0x3f 0x5b 0xf5 0x01 0x00 --Enable All interface
hcitool cmd 0x3f 0x5b 0xf5 0x01 0x01 --Enable Wlan interface
hcitool cmd 0x3f 0x5b 0xf5 0x01 0x02 --Enable BT interface
hcitool cmd 0x3f 0x5b 0xf5 0x00 0x00 --Disable All interface
hcitool cmd 0x3f 0x5b 0xf5 0x00 0x01 --Disable Wlan interface
hcitool cmd 0x3f 0x5b 0xf5 0x00 0x02 --Disable BT interface
SD8688 firmware
===============
Images:
- /lib/firmware/sd8688_helper.bin
- /lib/firmware/sd8688.bin
The images can be downloaded from:
git.infradead.org/users/dwmw2/linux-firmware.git/libertas/
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...