Revision 67d365a57a51fb9dece6a5ceb504aa381cae1e5b authored by Mark on 16 September 2014, 15:22:50 UTC, committed by Greg Kroah-Hartman on 19 September 2014, 22:01:38 UTC
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other than 0. I don't have a USBConnect 2000, but based on the other entries for Shuttle/ SCM-based converters this patch is very likely correct. I used 0x0000 and 0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which bcdDevice value the product uses. Signed-off-by: Mark Knibbs <markk@clara.co.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1 parent 7312b5d
adm1275
Kernel driver adm1275
=====================
Supported chips:
* Analog Devices ADM1075
Prefix: 'adm1075'
Addresses scanned: -
Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1075.pdf
* Analog Devices ADM1275
Prefix: 'adm1275'
Addresses scanned: -
Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1275.pdf
* Analog Devices ADM1276
Prefix: 'adm1276'
Addresses scanned: -
Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1276.pdf
Author: Guenter Roeck <linux@roeck-us.net>
Description
-----------
This driver supports hardware montoring for Analog Devices ADM1075, ADM1275,
and ADM1276 Hot-Swap Controller and Digital Power Monitor.
ADM1075, ADM1275, and ADM1276 are hot-swap controllers that allow a circuit
board to be removed from or inserted into a live backplane. They also feature
current and voltage readback via an integrated 12-bit analog-to-digital
converter (ADC), accessed using a PMBus interface.
The driver is a client driver to the core PMBus driver. Please see
Documentation/hwmon/pmbus for details on PMBus client drivers.
Usage Notes
-----------
This driver does not auto-detect devices. You will have to instantiate the
devices explicitly. Please see Documentation/i2c/instantiating-devices for
details.
The ADM1075, unlike many other PMBus devices, does not support internal voltage
or current scaling. Reported voltages, currents, and power are raw measurements,
and will typically have to be scaled.
Platform data support
---------------------
The driver supports standard PMBus driver platform data. Please see
Documentation/hwmon/pmbus for details.
Sysfs entries
-------------
The following attributes are supported. Limits are read-write, history reset
attributes are write-only, all other attributes are read-only.
in1_label "vin1" or "vout1" depending on chip variant and
configuration. On ADM1075, vout1 reports the voltage on
the VAUX pin.
in1_input Measured voltage.
in1_min Minimum Voltage.
in1_max Maximum voltage.
in1_min_alarm Voltage low alarm.
in1_max_alarm Voltage high alarm.
in1_highest Historical maximum voltage.
in1_reset_history Write any value to reset history.
curr1_label "iout1"
curr1_input Measured current.
curr1_max Maximum current.
curr1_max_alarm Current high alarm.
curr1_lcrit Critical minimum current. Depending on the chip
configuration, either curr1_lcrit or curr1_crit is
supported, but not both.
curr1_lcrit_alarm Critical current low alarm.
curr1_crit Critical maximum current. Depending on the chip
configuration, either curr1_lcrit or curr1_crit is
supported, but not both.
curr1_crit_alarm Critical current high alarm.
curr1_highest Historical maximum current.
curr1_reset_history Write any value to reset history.
power1_label "pin1"
power1_input Input power.
power1_reset_history Write any value to reset history.
Power attributes are supported on ADM1075 and ADM1276
only.
Computing file changes ...
