| 71aa60f | Linus Torvalds | 23 September 2017, 15:41:27 UTC | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net Pull networking fixes from David Miller: 1) Fix NAPI poll list corruption in enic driver, from Christian Lamparter. 2) Fix route use after free, from Eric Dumazet. 3) Fix regression in reuseaddr handling, from Josef Bacik. 4) Assert the size of control messages in compat handling since we copy it in from userspace twice. From Meng Xu. 5) SMC layer bug fixes (missing RCU locking, bad refcounting, etc.) from Ursula Braun. 6) Fix races in AF_PACKET fanout handling, from Willem de Bruijn. 7) Don't use ARRAY_SIZE on spinlock array which might have zero entries, from Geert Uytterhoeven. 8) Fix miscomputation of checksum in ipv6 udp code, from Subash Abhinov Kasiviswanathan. 9) Push the ipv6 header properly in ipv6 GRE tunnel driver, from Xin Long. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits) inet: fix improper empty comparison net: use inet6_rcv_saddr to compare sockets net: set tb->fast_sk_family net: orphan frags on stand-alone ptype in dev_queue_xmit_nit MAINTAINERS: update git tree locations for ieee802154 subsystem net: prevent dst uses after free net: phy: Fix truncation of large IRQ numbers in phy_attached_print() net/smc: no close wait in case of process shut down net/smc: introduce a delay net/smc: terminate link group if out-of-sync is received net/smc: longer delay for client link group removal net/smc: adapt send request completion notification net/smc: adjust net_device refcount net/smc: take RCU read lock for routing cache lookup net/smc: add receive timeout check net/smc: add missing dev_put net: stmmac: Cocci spatch "of_table" lan78xx: Use default values loaded from EEPROM/OTP after reset lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE lan78xx: Fix for eeprom read/write when device auto suspend ... | 23 September 2017, 15:41:27 UTC |
| 79444df | Linus Torvalds | 23 September 2017, 15:33:29 UTC | Merge tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor Pull apparmor updates from John Johansen: "This is the apparmor pull request, similar to SELinux and seccomp. It's the same series that I was sent to James' security tree + one regression fix that was found after the series was sent to James and would have been sent for v4.14-rc2. Features: - in preparation for secid mapping add support for absolute root view based labels - add base infastructure for socket mediation - add mount mediation - add signal mediation minor cleanups and changes: - be defensive, ensure unconfined profiles have dfas initialized - add more debug asserts to apparmorfs - enable policy unpacking to audit different reasons for failure - cleanup conditional check for label in label_print - Redundant condition: prev_ns. in [label.c:1498] Bug Fixes: - fix regression in apparmorfs DAC access permissions - fix build failure on sparc caused by undeclared signals - fix sparse report of incorrect type assignment when freeing label proxies - fix race condition in null profile creation - Fix an error code in aafs_create() - Fix logical error in verify_header() - Fix shadowed local variable in unpack_trans_table()" * tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor: apparmor: fix apparmorfs DAC access permissions apparmor: fix build failure on sparc caused by undeclared signals apparmor: fix incorrect type assignment when freeing proxies apparmor: ensure unconfined profiles have dfas initialized apparmor: fix race condition in null profile creation apparmor: move new_null_profile to after profile lookup fns() apparmor: add base infastructure for socket mediation apparmor: add more debug asserts to apparmorfs apparmor: make policy_unpack able to audit different info messages apparmor: add support for absolute root view based labels apparmor: cleanup conditional check for label in label_print apparmor: add mount mediation apparmor: add the ability to mediate signals apparmor: Redundant condition: prev_ns. in [label.c:1498] apparmor: Fix an error code in aafs_create() apparmor: Fix logical error in verify_header() apparmor: Fix shadowed local variable in unpack_trans_table() | 23 September 2017, 15:33:29 UTC |
| c65da8e | Linus Torvalds | 23 September 2017, 03:40:11 UTC | Merge tag 'acpi-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI fixes from Rafael Wysocki: "These fix the initialization of resources in the ACPI WDAT watchdog driver, a recent regression in the ACPI device properties handling, a recent change in behavior causing the ACPI_HANDLE() macro to only work for GPL code and create a MAINTAINERS entry for ACPI PMIC drivers in order to specify the official reviewers for that code. Specifics: - Fix the initialization of resources in the ACPI WDAT watchdog driver that uses unititialized memory which causes compiler warnings to be triggered (Arnd Bergmann). - Fix a recent regression in the ACPI device properties handling that causes some device properties data to be skipped during enumeration (Sakari Ailus). - Fix a recent change in behavior that caused the ACPI_HANDLE() macro to stop working for non-GPL code which is a problem for the NVidia binary graphics driver, for example (John Hubbard). - Add a MAINTAINERS entry for the ACPI PMIC drivers to specify the official reviewers for that code (Rafael Wysocki)" * tag 'acpi-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI: properties: Return _DSD hierarchical extension (data) sub-nodes correctly ACPI / bus: Make ACPI_HANDLE() work for non-GPL code again ACPI / watchdog: properly initialize resources ACPI / PMIC: Add code reviewers to MAINTAINERS | 23 September 2017, 03:40:11 UTC |
| 4e683f4 | David S. Miller | 23 September 2017, 03:33:18 UTC | Merge branch 'net-fix-reuseaddr-regression' Josef Bacik says: ==================== net: fix reuseaddr regression I introduced a regression when reworking the fastreuse port stuff that allows bind conflicts to occur once a reuseaddr successfully opens on an existing tb. The root cause is I reversed an if statement which caused us to set the tb as if there were no owners on the socket if there were, which obviously is not correct. Dave could you please queue these changes up for -stable, I've run them through the net tests and added another test to check for this problem specifically. ==================== Signed-off-by: David S. Miller <davem@davemloft.net> | 23 September 2017, 03:33:18 UTC |
| fbed24b | Josef Bacik | 23 September 2017, 00:20:08 UTC | inet: fix improper empty comparison When doing my reuseport rework I screwed up and changed a if (hlist_empty(&tb->owners)) to if (!hlist_empty(&tb->owners)) This is obviously bad as all of the reuseport/reuse logic was reversed, which caused weird problems like allowing an ipv4 bind conflict if we opened an ipv4 only socket on a port followed by an ipv6 only socket on the same port. Fixes: b9470c27607b ("inet: kill smallest_size and smallest_port") Reported-by: Cole Robinson <crobinso@redhat.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 23 September 2017, 03:33:17 UTC |
| 7a56673 | Josef Bacik | 23 September 2017, 00:20:07 UTC | net: use inet6_rcv_saddr to compare sockets In ipv6_rcv_saddr_equal() we need to use inet6_rcv_saddr(sk) for the ipv6 compare with the fast socket information to make sure we're doing the proper comparisons. Fixes: 637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk") Reported-and-tested-by: Cole Robinson <crobinso@redhat.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 23 September 2017, 03:33:17 UTC |
| cbb2fb5 | Josef Bacik | 23 September 2017, 00:20:06 UTC | net: set tb->fast_sk_family We need to set the tb->fast_sk_family properly so we can use the proper comparison function for all subsequent reuseport bind requests. Fixes: 637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk") Reported-and-tested-by: Cole Robinson <crobinso@redhat.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 23 September 2017, 03:33:17 UTC |
| 581fe0e | Willem de Bruijn | 22 September 2017, 23:42:37 UTC | net: orphan frags on stand-alone ptype in dev_queue_xmit_nit Zerocopy skbs frags are copied when the skb is looped to a local sock. Commit 1080e512d44d ("net: orphan frags on receive") introduced calls to skb_orphan_frags to deliver_skb and __netif_receive_skb for this. With msg_zerocopy, these skbs can also exist in the tx path and thus loop from dev_queue_xmit_nit. This already calls deliver_skb in its loop. But it does not orphan before a separate pt_prev->func(). Add the missing skb_orphan_frags_rx. Changes v1->v2: handle skb_orphan_frags_rx failure Fixes: 1f8b977ab32d ("sock: enable MSG_ZEROCOPY") Signed-off-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 23 September 2017, 03:31:29 UTC |
| 6876eb3 | Linus Torvalds | 23 September 2017, 03:28:59 UTC | Merge tag 'pm-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management fixes from Rafael Wysocki: "These fix a cpufreq regression introduced by recent changes related to the generic DT driver, an initialization time memory leak in cpuidle on ARM, a PM core bug that may cause system suspend/resume to fail on some systems, a request type validation issue in the PM QoS framework and two documentation-related issues. Specifics: - Fix a regression in cpufreq on systems using DT as the source of CPU configuration information where two different code paths attempt to create the cpufreq-dt device object (there can be only one) and fix up the "compatible" matching for some TI platforms on top of that (Viresh Kumar, Dave Gerlach). - Fix an initialization time memory leak in cpuidle on ARM which occurs if the cpuidle driver initialization fails (Stefan Wahren). - Fix a PM core function that checks whether or not there are any system suspend/resume callbacks for a device, but forgets to check legacy callbacks which then may be skipped incorrectly and the system may crash and/or the device may become unusable after a suspend-resume cycle (Rafael Wysocki). - Fix request type validation for latency tolerance PM QoS requests which may lead to unexpected behavior (Jan Schönherr). - Fix a broken link to PM documentation from a header file and a typo in a PM document (Geert Uytterhoeven, Rafael Wysocki)" * tag 'pm-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpufreq: ti-cpufreq: Support additional am43xx platforms ARM: cpuidle: Avoid memleak if init fail cpufreq: dt-platdev: Add some missing platforms to the blacklist PM: core: Fix device_pm_check_callbacks() PM: docs: Drop an excess character from devices.rst PM / QoS: Use the correct variable to check the QoS request type driver core: Fix link to device power management documentation | 23 September 2017, 03:28:59 UTC |
| d32e5f4 | Linus Torvalds | 23 September 2017, 03:23:41 UTC | Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: - fixes for two long standing issues (lock up and a crash) in force feedback handling in uinput driver - tweak to firmware update timing in Elan I2C touchpad driver. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: elan_i2c - extend Flash-Write delay Input: uinput - avoid crash when sending FF request to device going away Input: uinput - avoid FF flush when destroying device | 23 September 2017, 03:23:41 UTC |
| c0a3a64 | Linus Torvalds | 23 September 2017, 02:16:41 UTC | Merge tag 'seccomp-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull seccomp updates from Kees Cook: "Major additions: - sysctl and seccomp operation to discover available actions (tyhicks) - new per-filter configurable logging infrastructure and sysctl (tyhicks) - SECCOMP_RET_LOG to log allowed syscalls (tyhicks) - SECCOMP_RET_KILL_PROCESS as the new strictest possible action - self-tests for new behaviors" [ This is the seccomp part of the security pull request during the merge window that was nixed due to unrelated problems - Linus ] * tag 'seccomp-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: samples: Unrename SECCOMP_RET_KILL selftests/seccomp: Test thread vs process killing seccomp: Implement SECCOMP_RET_KILL_PROCESS action seccomp: Introduce SECCOMP_RET_KILL_PROCESS seccomp: Rename SECCOMP_RET_KILL to SECCOMP_RET_KILL_THREAD seccomp: Action to log before allowing seccomp: Filter flag to log all actions except SECCOMP_RET_ALLOW seccomp: Selftest for detection of filter flag support seccomp: Sysctl to configure actions that are allowed to be logged seccomp: Operation for checking if an action is available seccomp: Sysctl to display available actions seccomp: Provide matching filter for introspection selftests/seccomp: Refactor RET_ERRNO tests selftests/seccomp: Add simple seccomp overhead benchmark selftests/seccomp: Add tests for basic ptrace actions | 23 September 2017, 02:16:41 UTC |
| 69c902f | Linus Torvalds | 23 September 2017, 02:11:48 UTC | Merge tag '4.14-smb3-fixes-from-recent-test-events-for-stable' of git://git.samba.org/sfrench/cifs-2.6 Pull cifs fixes from Steve French: "Various SMB3 fixes for stable and security improvements from the recently completed SMB3/Samba test events * tag '4.14-smb3-fixes-from-recent-test-events-for-stable' of git://git.samba.org/sfrench/cifs-2.6: SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags SMB3: handle new statx fields SMB: Validate negotiate (to protect against downgrade) even if signing off cifs: release auth_key.response for reconnect. cifs: release cifs root_cred after exit_cifs CIFS: make arrays static const, reduces object code size [SMB3] Update session and share information displayed for debugging SMB2/SMB3 cifs: show 'soft' in the mount options for hard mounts SMB3: Warn user if trying to sign connection that authenticated as guest SMB3: Fix endian warning Fix SMB3.1.1 guest authentication to Samba | 23 September 2017, 02:11:48 UTC |
| b03fcfa | Linus Torvalds | 23 September 2017, 02:09:31 UTC | Merge tag 'ceph-for-4.14-rc2' of git://github.com/ceph/ceph-client Pull ceph fixes from Ilya Dryomov: "Two small but important fixes: RADOS semantic change in upcoming v12.2.1 release and a rare NULL dereference in create_session_open_msg()" * tag 'ceph-for-4.14-rc2' of git://github.com/ceph/ceph-client: ceph: avoid panic in create_session_open_msg() if utsname() returns NULL libceph: don't allow bidirectional swap of pg-upmap-items | 23 September 2017, 02:09:31 UTC |
| b9b95da | Stefan Schmidt | 22 September 2017, 12:28:46 UTC | MAINTAINERS: update git tree locations for ieee802154 subsystem Patches for ieee802154 will go through my new trees towards netdev from now on. The 6LoWPAN subsystem will stay as is (shared between ieee802154 and bluetooth) and go through the bluetooth tree as usual. Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 23 September 2017, 01:27:24 UTC |
| 1013e76 | Steve French | 22 September 2017, 06:40:27 UTC | SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags Signed-off-by: Steve French <smfrench@gmail.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> | 23 September 2017, 00:47:17 UTC |
| e2577d2 | Linus Torvalds | 22 September 2017, 23:09:11 UTC | Merge tag 'pci-v4.14-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixes from Bjorn Helgaas: - fix endpoint "end of test" interrupt issue (introduced in v4.14-rc1) (John Keeping) - fix MIPS use-after-free map_irq() issue (introduced in v4.14-rc1) (Lorenzo Pieralisi) * tag 'pci-v4.14-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: endpoint: Use correct "end of test" interrupt MIPS: PCI: Move map_irq() hooks out of initdata | 22 September 2017, 23:09:11 UTC |
| 9ae0b37 | Linus Torvalds | 22 September 2017, 23:06:05 UTC | Merge tag 'iommu-fixes-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu Pull IOMMU fixes from Joerg Roedel: - two Kconfig fixes to fix dependencies that cause compile failures when they are not fulfilled. - a section mismatch fix for Intel VT-d - a fix for PCI topology detection in ARM device-tree code * tag 'iommu-fixes-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu/of: Remove PCI host bridge node check iommu/qcom: Depend on HAS_DMA to fix compile error iommu/vt-d: Fix harmless section mismatch warning iommu: Add missing dependencies | 22 September 2017, 23:06:05 UTC |
| d21b8ea | Linus Torvalds | 22 September 2017, 23:02:54 UTC | Merge git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile Pull arch/tile fixes from Chris Metcalf: "These are a code cleanup and config cleanup, respectively" * git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: tile: array underflow in setup_maxnodemem() tile: defconfig: Cleanup from old Kconfig options | 22 September 2017, 23:02:54 UTC |
| 4d9af76 | Linus Torvalds | 22 September 2017, 23:01:16 UTC | Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Catalin Marinas: - #ifdef CONFIG_EFI around __efi_fpsimd_begin/end - Assembly code alignment reduced to 4 bytes from 16 - Ensure the kernel is compiled for LP64 (there are some arm64 compilers around defaulting to ILP32) - Fix arm_pmu_acpi memory leak on the error path * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: drivers/perf: arm_pmu_acpi: Release memory obtained by kasprintf arm64: ensure the kernel is compiled for LP64 arm64: relax assembly code alignment from 16 byte to 4 byte arm64: efi: Don't include EFI fpsimd save/restore code in non-EFI kernels | 22 September 2017, 23:01:16 UTC |
| 6e70e26 | Steve French | 22 September 2017, 02:32:29 UTC | SMB3: handle new statx fields We weren't returning the creation time or the two easily supported attributes (ENCRYPTED or COMPRESSED) for the getattr call to allow statx to return these fields. Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>\ Acked-by: Jeff Layton <jlayton@poochiereds.net> CC: Stable <stable@vger.kernel.org> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> | 22 September 2017, 23:00:41 UTC |
| c17c020 | Tobias Klauser | 22 September 2017, 07:42:42 UTC | arch: remove unused *_segments() macros/functions Some architectures define the no-op macros/functions copy_segments, release_segments and forget_segments. These are used nowhere in the tree, so removed them. Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Vineet Gupta <vgupta@synopsys.com> [for arch/arc] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> | 22 September 2017, 22:59:52 UTC |
| 672d0e4 | Rafael J. Wysocki | 22 September 2017, 21:38:45 UTC | Merge branches 'acpi-pmic', 'acpi-bus', 'acpi-wdat' and 'acpi-properties' * acpi-pmic: ACPI / PMIC: Add code reviewers to MAINTAINERS * acpi-bus: ACPI / bus: Make ACPI_HANDLE() work for non-GPL code again * acpi-wdat: ACPI / watchdog: properly initialize resources * acpi-properties: ACPI: properties: Return _DSD hierarchical extension (data) sub-nodes correctly | 22 September 2017, 21:38:45 UTC |
| d84c97f | Rafael J. Wysocki | 22 September 2017, 20:45:54 UTC | Merge branches 'pm-cpufreq' and 'pm-cpuidle' * pm-cpufreq: cpufreq: ti-cpufreq: Support additional am43xx platforms cpufreq: dt-platdev: Add some missing platforms to the blacklist * pm-cpuidle: ARM: cpuidle: Avoid memleak if init fail | 22 September 2017, 20:45:54 UTC |
| 1419d03 | Rafael J. Wysocki | 22 September 2017, 20:45:28 UTC | Merge branches 'pm-core', 'pm-qos' and 'pm-docs' * pm-core: PM: core: Fix device_pm_check_callbacks() * pm-qos: PM / QoS: Use the correct variable to check the QoS request type * pm-docs: PM: docs: Drop an excess character from devices.rst driver core: Fix link to device power management documentation | 22 September 2017, 20:45:28 UTC |
| bf81100 | John Johansen | 31 August 2017, 16:54:43 UTC | apparmor: fix apparmorfs DAC access permissions The DAC access permissions for several apparmorfs files are wrong. .access - needs to be writable by all tasks to perform queries the others in the set only provide a read fn so should be read only. With policy namespace virtualization all apparmor needs to control the permission and visibility checks directly which means DAC access has to be allowed for all user, group, and other. BugLink: http://bugs.launchpad.net/bugs/1713103 Fixes: c97204baf840b ("apparmor: rename apparmor file fns and data to indicate use") Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:20:01 UTC |
| b1545db | John Johansen | 23 August 2017, 19:10:39 UTC | apparmor: fix build failure on sparc caused by undeclared signals In file included from security/apparmor/ipc.c:23:0: security/apparmor/include/sig_names.h:26:3: error: 'SIGSTKFLT' undeclared here (not in a function) [SIGSTKFLT] = 16, /* -, 16, - */ ^ security/apparmor/include/sig_names.h:26:3: error: array index in initializer not of integer type security/apparmor/include/sig_names.h:26:3: note: (near initialization for 'sig_map') security/apparmor/include/sig_names.h:51:3: error: 'SIGUNUSED' undeclared here (not in a function) [SIGUNUSED] = 34, /* -, 31, - */ ^ security/apparmor/include/sig_names.h:51:3: error: array index in initializer not of integer type security/apparmor/include/sig_names.h:51:3: note: (near initialization for 'sig_map') Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: c6bf1adaecaa ("apparmor: add the ability to mediate signals") Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:58 UTC |
| bc4d82f | John Johansen | 16 August 2017, 16:33:48 UTC | apparmor: fix incorrect type assignment when freeing proxies sparse reports poisoning the proxy->label before freeing the struct is resulting in a sparse build warning. ../security/apparmor/label.c:52:30: warning: incorrect type in assignment (different address spaces) ../security/apparmor/label.c:52:30: expected struct aa_label [noderef] <asn:4>*label ../security/apparmor/label.c:52:30: got struct aa_label *<noident> fix with RCU_INIT_POINTER as this is one of those cases where rcu_assign_pointer() is not needed. Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:58 UTC |
| 15372b9 | John Johansen | 16 August 2017, 12:48:06 UTC | apparmor: ensure unconfined profiles have dfas initialized Generally unconfined has early bailout tests and does not need the dfas initialized, however if an early bailout test is ever missed it will result in an oops. Be defensive and initialize the unconfined profile to have null dfas (no permission) so if an early bailout test is missed we fail closed (no perms granted) instead of oopsing. Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:58 UTC |
| 290638a | John Johansen | 16 August 2017, 12:40:49 UTC | apparmor: fix race condition in null profile creation There is a race when null- profile is being created between the initial lookup/creation of the profile and lock/addition of the profile. This could result in multiple version of a profile being added to the list which need to be removed/replaced. Since these are learning profile their is no affect on mediation. Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:58 UTC |
| d07881d | John Johansen | 16 August 2017, 15:59:57 UTC | apparmor: move new_null_profile to after profile lookup fns() new_null_profile will need to use some of the profile lookup fns() so move instead of doing forward fn declarations. Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:58 UTC |
| 651e28c | John Johansen | 19 July 2017, 06:18:33 UTC | apparmor: add base infastructure for socket mediation Provide a basic mediation of sockets. This is not a full net mediation but just whether a spcific family of socket can be used by an application, along with setting up some basic infrastructure for network mediation to follow. the user space rule hav the basic form of NETWORK RULE = [ QUALIFIERS ] 'network' [ DOMAIN ] [ TYPE | PROTOCOL ] DOMAIN = ( 'inet' | 'ax25' | 'ipx' | 'appletalk' | 'netrom' | 'bridge' | 'atmpvc' | 'x25' | 'inet6' | 'rose' | 'netbeui' | 'security' | 'key' | 'packet' | 'ash' | 'econet' | 'atmsvc' | 'sna' | 'irda' | 'pppox' | 'wanpipe' | 'bluetooth' | 'netlink' | 'unix' | 'rds' | 'llc' | 'can' | 'tipc' | 'iucv' | 'rxrpc' | 'isdn' | 'phonet' | 'ieee802154' | 'caif' | 'alg' | 'nfc' | 'vsock' | 'mpls' | 'ib' | 'kcm' ) ',' TYPE = ( 'stream' | 'dgram' | 'seqpacket' | 'rdm' | 'raw' | 'packet' ) PROTOCOL = ( 'tcp' | 'udp' | 'icmp' ) eg. network, network inet, Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Seth Arnold <seth.arnold@canonical.com> | 22 September 2017, 20:00:58 UTC |
| cbf2d0e | John Johansen | 19 July 2017, 06:41:13 UTC | apparmor: add more debug asserts to apparmorfs Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Seth Arnold <seth.arnold@canonical.com> | 22 September 2017, 20:00:58 UTC |
| 2410aa9 | John Johansen | 19 July 2017, 06:37:18 UTC | apparmor: make policy_unpack able to audit different info messages Switch unpack auditing to using the generic name field in the audit struct and make it so we can start adding new info messages about why an unpack failed. Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Seth Arnold <seth.arnold@canonical.com> | 22 September 2017, 20:00:58 UTC |
| 26b7899 | John Johansen | 06 August 2017, 12:39:08 UTC | apparmor: add support for absolute root view based labels With apparmor policy virtualization based on policy namespace View's we don't generally want/need absolute root based views, however there are cases like debugging and some secid based conversions where using a root based view is important. Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Seth Arnold <seth.arnold@canonical.com> | 22 September 2017, 20:00:58 UTC |
| f872af7 | John Johansen | 06 August 2017, 12:36:40 UTC | apparmor: cleanup conditional check for label in label_print Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Seth Arnold <seth.arnold@canonical.com> | 22 September 2017, 20:00:57 UTC |
| 2ea3ffb | John Johansen | 19 July 2017, 06:04:47 UTC | apparmor: add mount mediation Add basic mount mediation. That allows controlling based on basic mount parameters. It does not include special mount parameters for apparmor, super block labeling, or any triggers for apparmor namespace parameter modifications on pivot root. default userspace policy rules have the form of MOUNT RULE = ( MOUNT | REMOUNT | UMOUNT ) MOUNT = [ QUALIFIERS ] 'mount' [ MOUNT CONDITIONS ] [ SOURCE FILEGLOB ] [ '->' MOUNTPOINT FILEGLOB ] REMOUNT = [ QUALIFIERS ] 'remount' [ MOUNT CONDITIONS ] MOUNTPOINT FILEGLOB UMOUNT = [ QUALIFIERS ] 'umount' [ MOUNT CONDITIONS ] MOUNTPOINT FILEGLOB MOUNT CONDITIONS = [ ( 'fstype' | 'vfstype' ) ( '=' | 'in' ) MOUNT FSTYPE EXPRESSION ] [ 'options' ( '=' | 'in' ) MOUNT FLAGS EXPRESSION ] MOUNT FSTYPE EXPRESSION = ( MOUNT FSTYPE LIST | MOUNT EXPRESSION ) MOUNT FSTYPE LIST = Comma separated list of valid filesystem and virtual filesystem types (eg ext4, debugfs, etc) MOUNT FLAGS EXPRESSION = ( MOUNT FLAGS LIST | MOUNT EXPRESSION ) MOUNT FLAGS LIST = Comma separated list of MOUNT FLAGS. MOUNT FLAGS = ( 'ro' | 'rw' | 'nosuid' | 'suid' | 'nodev' | 'dev' | 'noexec' | 'exec' | 'sync' | 'async' | 'remount' | 'mand' | 'nomand' | 'dirsync' | 'noatime' | 'atime' | 'nodiratime' | 'diratime' | 'bind' | 'rbind' | 'move' | 'verbose' | 'silent' | 'loud' | 'acl' | 'noacl' | 'unbindable' | 'runbindable' | 'private' | 'rprivate' | 'slave' | 'rslave' | 'shared' | 'rshared' | 'relatime' | 'norelatime' | 'iversion' | 'noiversion' | 'strictatime' | 'nouser' | 'user' ) MOUNT EXPRESSION = ( ALPHANUMERIC | AARE ) ... PIVOT ROOT RULE = [ QUALIFIERS ] pivot_root [ oldroot=OLD PUT FILEGLOB ] [ NEW ROOT FILEGLOB ] SOURCE FILEGLOB = FILEGLOB MOUNTPOINT FILEGLOB = FILEGLOB eg. mount, mount /dev/foo, mount options=ro /dev/foo -> /mnt/, mount options in (ro,atime) /dev/foo -> /mnt/, mount options=ro options=atime, Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Seth Arnold <seth.arnold@canonical.com> | 22 September 2017, 20:00:57 UTC |
| cd1dbf7 | John Johansen | 19 July 2017, 05:56:22 UTC | apparmor: add the ability to mediate signals Add signal mediation where the signal can be mediated based on the signal, direction, or the label or the peer/target. The signal perms are verified on a cross check to ensure policy consistency in the case of incremental policy load/replacement. The optimization of skipping the cross check when policy is guaranteed to be consistent (single compile unit) remains to be done. policy rules have the form of SIGNAL_RULE = [ QUALIFIERS ] 'signal' [ SIGNAL ACCESS PERMISSIONS ] [ SIGNAL SET ] [ SIGNAL PEER ] SIGNAL ACCESS PERMISSIONS = SIGNAL ACCESS | SIGNAL ACCESS LIST SIGNAL ACCESS LIST = '(' Comma or space separated list of SIGNAL ACCESS ')' SIGNAL ACCESS = ( 'r' | 'w' | 'rw' | 'read' | 'write' | 'send' | 'receive' ) SIGNAL SET = 'set' '=' '(' SIGNAL LIST ')' SIGNAL LIST = Comma or space separated list of SIGNALS SIGNALS = ( 'hup' | 'int' | 'quit' | 'ill' | 'trap' | 'abrt' | 'bus' | 'fpe' | 'kill' | 'usr1' | 'segv' | 'usr2' | 'pipe' | 'alrm' | 'term' | 'stkflt' | 'chld' | 'cont' | 'stop' | 'stp' | 'ttin' | 'ttou' | 'urg' | 'xcpu' | 'xfsz' | 'vtalrm' | 'prof' | 'winch' | 'io' | 'pwr' | 'sys' | 'emt' | 'exists' | 'rtmin+0' ... 'rtmin+32' ) SIGNAL PEER = 'peer' '=' AARE eg. signal, # allow all signals signal send set=(hup, kill) peer=foo, Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Seth Arnold <seth.arnold@canonical.com> | 22 September 2017, 20:00:57 UTC |
| c556170 | John Johansen | 01 August 2017, 06:44:37 UTC | apparmor: Redundant condition: prev_ns. in [label.c:1498] Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:57 UTC |
| 5d314a8 | Dan Carpenter | 13 July 2017, 07:39:20 UTC | apparmor: Fix an error code in aafs_create() We accidentally forgot to set the error code on this path. It means we return NULL instead of an error pointer. I looked through a bunch of callers and I don't think it really causes a big issue, but the documentation says we're supposed to return error pointers here. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Serge Hallyn <serge@hallyn.com> Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:57 UTC |
| 86aea56 | Christos Gkekas | 08 July 2017, 19:50:21 UTC | apparmor: Fix logical error in verify_header() verify_header() is currently checking whether interface version is less than 5 *and* greater than 7, which always evaluates to false. Instead it should check whether it is less than 5 *or* greater than 7. Signed-off-by: Christos Gkekas <chris.gekas@gmail.com> Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:57 UTC |
| 19fe43a | Geert Uytterhoeven | 06 July 2017, 08:56:21 UTC | apparmor: Fix shadowed local variable in unpack_trans_table() with W=2: security/apparmor/policy_unpack.c: In function ‘unpack_trans_table’: security/apparmor/policy_unpack.c:469: warning: declaration of ‘pos’ shadows a previous local security/apparmor/policy_unpack.c:451: warning: shadowed declaration is here Rename the old "pos" to "saved_pos" to fix this. Fixes: 5379a3312024a8be ("apparmor: support v7 transition format compatible with label_parse") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Serge Hallyn <serge@hallyn.com> Signed-off-by: John Johansen <john.johansen@canonical.com> | 22 September 2017, 20:00:57 UTC |
| 05f5c38 | KT Liao | 22 September 2017, 17:00:57 UTC | Input: elan_i2c - extend Flash-Write delay The original 20ms delay is only marginally enough delay after a block write operation during firmware update. Let's increase the delay to ensure that the controller finishes up storing the page to avoid failures in the firmware updates. Signed-off-by: KT Liao <kt.liao@emc.com.tw> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> | 22 September 2017, 17:07:38 UTC |
| 0a8abd9 | Linus Torvalds | 22 September 2017, 16:40:47 UTC | Merge tag 'for-linus-4.14b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixes from Juergen Gross: "A fix for a missing __init annotation and two cleanup patches" * tag 'for-linus-4.14b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen, arm64: drop dummy lookup_address() xen: don't compile pv-specific parts if XEN_PV isn't configured xen: x86: mark xen_find_pt_base as __init | 22 September 2017, 16:40:47 UTC |
| d6396a7 | Linus Torvalds | 22 September 2017, 16:39:09 UTC | Merge tag 'powerpc-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: "It turns out our single-fix pull from last week was too good to be true. I missed a few fixes in that pull that had already come in because I was on leave, but also we hadn't found the bugs yet. So this week it's a bit bigger, though not ridiculous. Hopefully things will settle down from here on. Four fixes for the new instruction emulation code. A fix for CPU offline on bare metal machines when certain idle states are not supported, and a fix for a device_node refcounting oops during CPU hotplug, caused by recent changes. Going to stable are a fix for an oops during core dump on machines that have TM (Transactional Memory) disabled. Reordering some EEH initialisation to avoid trashing memory, and another device_node refcounting fix. And a few other minor things. Thanks to: Anton Blanchard, Benjamin Herrenschmidt, Cyril Bur, Gautham R. Shenoy, Gustavo Romero, Kamalesh Babulal, Matthew Weber, Matt Weber, Naveen N. Rao, Nicholas Piggin, Pavithra Prakash, Ravi Bangoria, Ronak Desai, Scott Wood, Tyrel Datwyler" * tag 'powerpc-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/pseries: Fix parent_dn reference leak in add_dt_node() powerpc/pseries: Fix "OF: ERROR: Bad of_node_put() on /cpus" during DLPAR powerpc/eeh: Create PHB PEs after EEH is initialized powerpc/kprobes: Update optprobes to use emulate_update_regs() powerpc/powernv: Clear LPCR[PECE1] via stop-api only for deep state offline powerpc/sstep: mullw should calculate a 64 bit signed result powerpc/sstep: Fix issues with mcrf powerpc/sstep: Fix issues with set_cr0() powerpc/tm: Flush TM only if CPU has TM feature powerpc/sysrq: Fix oops whem ppmu is not registered powerpc/configs: Update for CONFIG_SND changes powerpc/e6500: Update machine check for L1D cache err | 22 September 2017, 16:39:09 UTC |
| 7e6d8f8 | Linus Torvalds | 22 September 2017, 16:37:50 UTC | Merge branch '4.14-fixes' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus Pull MIPS fixes from Ralf Baechle: - Fix a build error on MSP71xx which used to rely on somehow magically <asm/setup.h> being pulled in which no longer happens. - Fix the __write_64bit_c0_split inline assembler where there was the theoretical possibility of GCC interpret the constraints such that bad code could result. - A __init was causing section mismatch errors on Alchemy. Just to be on the safe side, Manuel's patch does away with all of them. - Fix perf event init. * '4.14-fixes' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: PCI: fix pcibios_map_irq section mismatch MIPS: Fix input modify in __write_64bit_c0_split() MIPS: MSP71xx: Include asm/setup.h MIPS: Fix perf event init | 22 September 2017, 16:37:50 UTC |
| c8107ed | Linus Torvalds | 22 September 2017, 16:32:07 UTC | Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Martin Schwidefsky: - A couple of bug fixes: memory management, perf, cio, dasd and scm_blk. - A larger change in regard to the CPU topology to improve performance for systems running under z/VM or KVM. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/topology: enable / disable topology dynamically s390/topology: alternative topology for topology-less machines s390/mm: fix write access check in gup_huge_pmd() s390/mm: make pmdp_invalidate() do invalidation only s390/cio: recover from bad paths s390/scm_blk: consistently use blk_status_t as error type s390/dasd: fix race during dasd initialization s390/perf: fix bug when creating per-thread event | 22 September 2017, 16:32:07 UTC |
| 7a6d007 | Linus Torvalds | 22 September 2017, 16:15:27 UTC | Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fixes from Herbert Xu: - Fix compiler warnings in inside-secure - Fix LS1021A support in caam - Avoid using RBP in x86 crypto code - Fix bug in talitos that prevents hashing with algif - Fix bugs talitos hashing code that cause incorrect hash result - Fix memory freeing path bug in drbg - Fix af_alg crash when two SG lists are chained * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: af_alg - update correct dst SGL entry crypto: caam - fix LS1021A support on ARMv7 multiplatform kernel crypto: inside-secure - fix gcc-4.9 warnings crypto: talitos - Don't provide setkey for non hmac hashing algs crypto: talitos - fix hashing crypto: talitos - fix sha224 crypto: x86/twofish - Fix RBP usage crypto: sha512-avx2 - Fix RBP usage crypto: x86/sha256-ssse3 - Fix RBP usage crypto: x86/sha256-avx2 - Fix RBP usage crypto: x86/sha256-avx - Fix RBP usage crypto: x86/sha1-ssse3 - Fix RBP usage crypto: x86/sha1-avx2 - Fix RBP usage crypto: x86/des3_ede - Fix RBP usage crypto: x86/cast6 - Fix RBP usage crypto: x86/cast5 - Fix RBP usage crypto: x86/camellia - Fix RBP usage crypto: x86/blowfish - Fix RBP usage crypto: drbg - fix freeing of resources | 22 September 2017, 16:15:27 UTC |
| a88dc7b | Arvind Yadav | 20 September 2017, 06:56:38 UTC | drivers/perf: arm_pmu_acpi: Release memory obtained by kasprintf Free memory region, if arm_pmu_acpi_probe is not successful. Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> | 22 September 2017, 14:11:46 UTC |
| c0d05cd | Robin Murphy | 21 September 2017, 10:20:58 UTC | iommu/of: Remove PCI host bridge node check of_pci_iommu_init() tries to be clever and stop its alias walk at the device represented by master_np, in case of weird PCI topologies where the bridge to the IOMMU and the rest of the system is not at the root. It turns out this is a bit short-sighted, since there are plenty of other callers of pci_for_each_dma_alias() which would also need the same behaviour in that situation, and the only platform so far with such a topology (Cavium ThunderX2) already solves it more generally via a PCI quirk. As this check is effectively redundant, and returning a boolean value as an int is a bit broken anyway, let's just get rid of it. Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Fixes: d87beb749281 ("iommu/of: Handle PCI aliases properly") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Tested-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> | 22 September 2017, 10:05:43 UTC |
| 222d7db | Eric Dumazet | 21 September 2017, 16:15:46 UTC | net: prevent dst uses after free In linux-4.13, Wei worked hard to convert dst to a traditional refcounted model, removing GC. We now want to make sure a dst refcount can not transition from 0 back to 1. The problem here is that input path attached a not refcounted dst to an skb. Then later, because packet is forwarded and hits skb_dst_force() before exiting RCU section, we might try to take a refcount on one dst that is about to be freed, if another cpu saw 1 -> 0 transition in dst_release() and queued the dst for freeing after one RCU grace period. Lets unify skb_dst_force() and skb_dst_force_safe(), since we should always perform the complete check against dst refcount, and not assume it is not zero. Bugzilla : https://bugzilla.kernel.org/show_bug.cgi?id=197005 [ 989.919496] skb_dst_force+0x32/0x34 [ 989.919498] __dev_queue_xmit+0x1ad/0x482 [ 989.919501] ? eth_header+0x28/0xc6 [ 989.919502] dev_queue_xmit+0xb/0xd [ 989.919504] neigh_connected_output+0x9b/0xb4 [ 989.919507] ip_finish_output2+0x234/0x294 [ 989.919509] ? ipt_do_table+0x369/0x388 [ 989.919510] ip_finish_output+0x12c/0x13f [ 989.919512] ip_output+0x53/0x87 [ 989.919513] ip_forward_finish+0x53/0x5a [ 989.919515] ip_forward+0x2cb/0x3e6 [ 989.919516] ? pskb_trim_rcsum.part.9+0x4b/0x4b [ 989.919518] ip_rcv_finish+0x2e2/0x321 [ 989.919519] ip_rcv+0x26f/0x2eb [ 989.919522] ? vlan_do_receive+0x4f/0x289 [ 989.919523] __netif_receive_skb_core+0x467/0x50b [ 989.919526] ? tcp_gro_receive+0x239/0x239 [ 989.919529] ? inet_gro_receive+0x226/0x238 [ 989.919530] __netif_receive_skb+0x4d/0x5f [ 989.919532] netif_receive_skb_internal+0x5c/0xaf [ 989.919533] napi_gro_receive+0x45/0x81 [ 989.919536] ixgbe_poll+0xc8a/0xf09 [ 989.919539] ? kmem_cache_free_bulk+0x1b6/0x1f7 [ 989.919540] net_rx_action+0xf4/0x266 [ 989.919543] __do_softirq+0xa8/0x19d [ 989.919545] irq_exit+0x5d/0x6b [ 989.919546] do_IRQ+0x9c/0xb5 [ 989.919548] common_interrupt+0x93/0x93 [ 989.919548] </IRQ> Similarly dst_clone() can use dst_hold() helper to have additional debugging, as a follow up to commit 44ebe79149ff ("net: add debug atomic_inc_not_zero() in dst_hold()") In net-next we will convert dst atomic_t to refcount_t for peace of mind. Fixes: a4c2fd7f7891 ("net: remove DST_NOCACHE flag") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Reported-by: Paweł Staszewski <pstaszewski@itcare.pl> Bisected-by: Paweł Staszewski <pstaszewski@itcare.pl> Acked-by: Wei Wang <weiwan@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 22 September 2017, 03:42:15 UTC |
| 059fbe8 | Geert Uytterhoeven | 21 September 2017, 11:27:02 UTC | net: phy: Fix truncation of large IRQ numbers in phy_attached_print() Given NR_IRQS is 2048 on sparc64, and even 32784 on alpha, 3 digits is not enough to represent interrupt numbers on all architectures. Hence PHY interrupt numbers may be truncated during printing. Increase the buffer size from 4 to 8 bytes to fix this. Fixes: 5e369aefdce4818c ("net: stmmac: Delete dead code for MDIO registration") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> | 22 September 2017, 03:35:17 UTC |
| 6e80ecd | Linus Torvalds | 22 September 2017, 01:51:19 UTC | Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull libnvdimm fixes from Dan Williams: "A crash fix and corresponding regression test enabling for the crash scenario. The unit test for this crash is available in ndctl-v58.2. This branch has received a build success notification from the 0day-kbuild robot over 148 configs. The fix is tagged for -stable / backport to 4.13" * 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: libnvdimm, namespace: fix btt claim class crash tools/testing/nvdimm: disable labels for nfit_test.1 | 22 September 2017, 01:51:19 UTC |
| 6b4877c | Dmitry Torokhov | 06 September 2017, 23:22:59 UTC | Input: uinput - avoid crash when sending FF request to device going away If FF request comes in while uinput device is going away, uinput_request_send() will fail with -ENODEV, and uinput_request_submit() will attempt to mark the slot as unused by calling uinput_request_done(). Unfortunately in this case we haven't initialized request->done completion yet, and we get a crash: [ 39.402036] BUG: spinlock bad magic on CPU#1, fftest/3108 [ 39.402046] lock: 0xffff88006a93bb00, .magic: 00000000, .owner: /39, .owner_cpu: 1217155072 [ 39.402055] CPU: 1 PID: 3108 Comm: fftest Tainted: G W 4.13.0+ #15 [ 39.402059] Hardware name: LENOVO 20HQS0EG02/20HQS0EG02, BIOS N1MET37W (1.22 ) 07/04/2017 [ 39.402064] 0000000000000086 f0fad82f3ceaa120 ffff88006a93b9a0 ffffffff9de941bb [ 39.402077] ffff88026df8ae00 ffff88006a93bb00 ffff88006a93b9c0 ffffffff9dca62b7 [ 39.402088] ffff88006a93bb00 ffff88006a93baf8 ffff88006a93b9e0 ffffffff9dca62e7 [ 39.402099] Call Trace: [ 39.402112] [<ffffffff9de941bb>] dump_stack+0x4d/0x63 [ 39.402123] [<ffffffff9dca62b7>] spin_dump+0x97/0x9c [ 39.402130] [<ffffffff9dca62e7>] spin_bug+0x2b/0x2d [ 39.402138] [<ffffffff9dca6373>] do_raw_spin_lock+0x28/0xfd [ 39.402147] [<ffffffff9e3055cd>] _raw_spin_lock_irqsave+0x19/0x1f [ 39.402154] [<ffffffff9dca05b7>] complete+0x1d/0x48 [ 39.402162] [<ffffffffc04f30af>] 0xffffffffc04f30af [ 39.402167] [<ffffffffc04f468c>] 0xffffffffc04f468c [ 39.402177] [<ffffffff9dd59c16>] ? __slab_free+0x22f/0x359 [ 39.402184] [<ffffffff9dcc13e9>] ? tk_clock_read+0xc/0xe [ 39.402189] [<ffffffffc04f471f>] 0xffffffffc04f471f [ 39.402195] [<ffffffff9dc9ffe5>] ? __wake_up+0x44/0x4b [ 39.402200] [<ffffffffc04f3240>] ? 0xffffffffc04f3240 [ 39.402207] [<ffffffff9e0f57f3>] erase_effect+0xa1/0xd2 [ 39.402214] [<ffffffff9e0f58c6>] input_ff_flush+0x43/0x5c [ 39.402219] [<ffffffffc04f32ad>] 0xffffffffc04f32ad [ 39.402227] [<ffffffff9e0f174f>] input_flush_device+0x3d/0x51 [ 39.402234] [<ffffffff9e0f69ae>] evdev_flush+0x49/0x5c [ 39.402243] [<ffffffff9dd62d6e>] filp_close+0x3f/0x65 [ 39.402253] [<ffffffff9dd7dcf7>] put_files_struct+0x66/0xc1 [ 39.402261] [<ffffffff9dd7ddeb>] exit_files+0x47/0x4e [ 39.402270] [<ffffffff9dc6b329>] do_exit+0x483/0x969 [ 39.402278] [<ffffffff9dc73211>] ? recalc_sigpending_tsk+0x3d/0x44 [ 39.402285] [<ffffffff9dc6c7a2>] do_group_exit+0x42/0xb0 [ 39.402293] [<ffffffff9dc767e1>] get_signal+0x58d/0x5bf [ 39.402300] [<ffffffff9dc03701>] do_signal+0x37/0x53e [ 39.402307] [<ffffffff9e0f8401>] ? evdev_ioctl_handler+0xac8/0xb04 [ 39.402314] [<ffffffff9e0f8464>] ? evdev_ioctl+0x10/0x12 [ 39.402321] [<ffffffff9dd74cfa>] ? do_vfs_ioctl+0x42e/0x501 [ 39.402328] [<ffffffff9dc0170e>] prepare_exit_to_usermode+0x66/0x90 [ 39.402333] [<ffffffff9dc0181b>] syscall_return_slowpath+0xe3/0xec [ 39.402339] [<ffffffff9e305b7b>] int_ret_from_sys_call+0x25/0x8f While we could solve this by simply initializing the completion earlier, we are better off rearranging the code a bit so we avoid calling complete() on requests that we did not send out. This patch consolidates marking request slots as free in one place (in uinput_request_submit(), the same place where we acquire them) and having everyone else simply signal completion of the requests. Fixes: 00ce756ce53a ("Input: uinput - mark failed submission requests as free") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> | 21 September 2017, 23:31:23 UTC |
| e8b9572 | Dmitry Torokhov | 02 September 2017, 00:13:43 UTC | Input: uinput - avoid FF flush when destroying device Normally, when input device supporting force feedback effects is being destroyed, we try to "flush" currently playing effects, so that the physical device does not continue vibrating (or executing other effects). Unfortunately this does not work well for uinput as flushing of the effects deadlocks with the destroy action: - if device is being destroyed because the file descriptor is being closed, then there is noone to even service FF requests; - if device is being destroyed because userspace sent UI_DEV_DESTROY, while theoretically it could be possible to service FF requests, userspace is unlikely to do so (they'd need to make sure FF handling happens on a separate thread) even if kernel solves the issue with FF ioctls deadlocking with UI_DEV_DESTROY ioctl on udev->mutex. To avoid lockups like the one below, let's install a custom input device flush handler, and avoid trying to flush force feedback effects when we destroying the device, and instead rely on uinput to shut off the device properly. NMI watchdog: Watchdog detected hard LOCKUP on cpu 3 ... <<EOE>> [<ffffffff817a0307>] _raw_spin_lock_irqsave+0x37/0x40 [<ffffffff810e633d>] complete+0x1d/0x50 [<ffffffffa00ba08c>] uinput_request_done+0x3c/0x40 [uinput] [<ffffffffa00ba587>] uinput_request_submit.part.7+0x47/0xb0 [uinput] [<ffffffffa00bb62b>] uinput_dev_erase_effect+0x5b/0x76 [uinput] [<ffffffff815d91ad>] erase_effect+0xad/0xf0 [<ffffffff815d929d>] flush_effects+0x4d/0x90 [<ffffffff815d4cc0>] input_flush_device+0x40/0x60 [<ffffffff815daf1c>] evdev_cleanup+0xac/0xc0 [<ffffffff815daf5b>] evdev_disconnect+0x2b/0x60 [<ffffffff815d74ac>] __input_unregister_device+0xac/0x150 [<ffffffff815d75f7>] input_unregister_device+0x47/0x70 [<ffffffffa00bac45>] uinput_destroy_device+0xb5/0xc0 [uinput] [<ffffffffa00bb2de>] uinput_ioctl_handler.isra.9+0x65e/0x740 [uinput] [<ffffffff811231ab>] ? do_futex+0x12b/0xad0 [<ffffffffa00bb3f8>] uinput_ioctl+0x18/0x20 [uinput] [<ffffffff81241248>] do_vfs_ioctl+0x298/0x480 [<ffffffff81337553>] ? security_file_ioctl+0x43/0x60 [<ffffffff812414a9>] SyS_ioctl+0x79/0x90 [<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71 Reported-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com> Reported-by: Clément VUCHENER <clement.vuchener@gmail.com> Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=193741 Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> | 21 September 2017, 23:31:22 UTC |
| 5d6b66c | David S. Miller | 21 September 2017, 22:31:03 UTC | Merge branch 'smc-bug-fixes' Ursula Braun says: ==================== net/smc: bug fixes 2017-09-20 here is a collection of small smc-patches built for net fixing smc problems in different areas. ==================== Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:03 UTC |
| 8c96fee | Ursula Braun | 21 September 2017, 07:16:34 UTC | net/smc: no close wait in case of process shut down Usually socket closing is delayed if there is still data available in the send buffer to be transmitted. If a process is killed, the delay should be avoided. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:03 UTC |
| 18e537c | Ursula Braun | 21 September 2017, 07:16:33 UTC | net/smc: introduce a delay The number of outstanding work requests is limited. If all work requests are in use, tx processing is postponed to another scheduling of the tx worker. Switch to a delayed worker to have a gap for tx completion queue events before the next retry. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:03 UTC |
| bfbedfd | Ursula Braun | 21 September 2017, 07:16:32 UTC | net/smc: terminate link group if out-of-sync is received An out-of-sync condition can just be detected by the client. If the server receives a CLC DECLINE message indicating an out-of-sync condition for the link groups, the server must clean up the out-of-sync link group. There is no need for an extra third parameter in smc_clc_send_decline(). Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:03 UTC |
| 5bc11dd | Ursula Braun | 21 September 2017, 07:16:31 UTC | net/smc: longer delay for client link group removal Client link group creation always follows the server linkgroup creation. If peer creates a new server link group, client has to create a new client link group. If peer reuses a server link group for a new connection, client has to reuse its client link group as well. This patch introduces a longer delay for client link group removal to make sure this link group still exists, once the peer decides to reuse a server link group. This avoids out-of-sync conditions for link groups. If already scheduled, modify the delay. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:03 UTC |
| 8301fa4 | Ursula Braun | 21 September 2017, 07:16:30 UTC | net/smc: adapt send request completion notification The solicited flag is meaningful for the receive completion queue. Ask for next work completion of any type on the send queue. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:03 UTC |
| a6832c3 | Ursula Braun | 21 September 2017, 07:16:29 UTC | net/smc: adjust net_device refcount smc_pnet_fill_entry() uses dev_get_by_name() adding a refcount to ndev. The following smc_pnet_enter() has to reduce the refcount if the entry to be added exists already in the pnet table. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:02 UTC |
| 731b008 | Ursula Braun | 21 September 2017, 07:16:28 UTC | net/smc: take RCU read lock for routing cache lookup smc_netinfo_by_tcpsk() looks up the routing cache. Such a lookup requires protection by an RCU read lock. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:02 UTC |
| 846e344 | Hans Wippel | 21 September 2017, 07:16:27 UTC | net/smc: add receive timeout check The SMC receive function currently lacks a timeout check under the condition that no data were received and no data are available. This patch adds such a check. Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:02 UTC |
| 09579ac | Hans Wippel | 21 September 2017, 07:16:26 UTC | net/smc: add missing dev_put In the infiniband part, SMC currently uses get_netdev which calls dev_hold on the returned net device. However, the SMC code never calls dev_put on that net device resulting in a wrong reference count. This patch adds a dev_put after the usage of the net device to fix the issue. Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:31:02 UTC |
| f0ef1f4 | Thomas Meyer | 21 September 2017, 06:24:27 UTC | net: stmmac: Cocci spatch "of_table" Make sure (of/i2c/platform)_device_id tables are NULL terminated. Found by coccinelle spatch "misc/of_table.cocci" Signed-off-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:26:26 UTC |
| 687740c | David S. Miller | 21 September 2017, 22:22:54 UTC | Merge branch 'lan78xx-fixes' Nisar Sayed says: ==================== lan78xx: This series of patches are for lan78xx driver. This series of patches are for lan78xx driver. These patches fixes potential issues associated with lan78xx driver. v5 - Updated changes as per comments v4 - Updated changes to handle return values as per comments - Updated EEPROM write handling as per comments v3 - Updated chagnes as per comments v2 - Added patch version information - Added fixes tag - Updated patch description - Updated chagnes as per comments v1 - Splitted patches as per comments - Dropped "fixed_phy device support" and "Fix for system suspend" changes ==================== Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:22:54 UTC |
| e365280 | Nisar Sayed | 20 September 2017, 21:06:38 UTC | lan78xx: Use default values loaded from EEPROM/OTP after reset Use default value of auto duplex and auto speed values loaded from EEPROM/OTP after reset. The LAN78xx allows platform configurations to be loaded from EEPROM/OTP. Ex: When external phy is connected, the MAC can be configured to have correct auto speed, auto duplex, auto polarity configured from the EEPROM/OTP. Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:22:53 UTC |
| c077682 | Nisar Sayed | 20 September 2017, 21:06:37 UTC | lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE Allow EEPROM write for less than MAX_EEPROM_SIZE Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:22:53 UTC |
| 8a7ffeb | Nisar Sayed | 20 September 2017, 21:06:36 UTC | lan78xx: Fix for eeprom read/write when device auto suspend Fix for eeprom read/write when device auto suspend Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:22:53 UTC |
| 59ec693 | David S. Miller | 21 September 2017, 22:20:41 UTC | Merge branch 'phylib-xcvr-type' Florian Fainelli says: ==================== net: Bring back transceiver type for PHYLIB With the introduction of the xLINKSETTINGS ethtool APIs, the transceiver type was deprecated, but in that process we lost some useful information that PHYLIB was consistently reporting about internal vs. external PHYs. This brings back transceiver as a read-only field that is only consumed in the legacy path where ETHTOOL_GET is called but the underlying drivers implement the new style klink_settings API. ==================== Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:20:41 UTC |
| ceb6281 | Florian Fainelli | 20 September 2017, 22:52:14 UTC | net: phy: Keep reporting transceiver type With commit 2d55173e71b0 ("phy: add generic function to support ksetting support"), we lost the ability to report the transceiver type like we used to. Now that we have added back the transceiver type to ethtool_link_settings, we can report it back like we used to and have no loss of information. Fixes: 3f1ac7a700d0 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API") Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:20:40 UTC |
| 19cab88 | Florian Fainelli | 20 September 2017, 22:52:13 UTC | net: ethtool: Add back transceiver type Commit 3f1ac7a700d0 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API") deprecated the ethtool_cmd::transceiver field, which was fine in premise, except that the PHY library was actually using it to report the type of transceiver: internal or external. Use the first word of the reserved field to put this __u8 transceiver field back in. It is made read-only, and we don't expect the ETHTOOL_xLINKSETTINGS API to be doing anything with this anyway, so this is mostly for the legacy path where we do: ethtool_get_settings() -> dev->ethtool_ops->get_link_ksettings() -> convert_link_ksettings_to_legacy_settings() to have no information loss compared to the legacy get_settings API. Fixes: 3f1ac7a700d0 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:20:40 UTC |
| 4a7a386 | Timur Tabi | 20 September 2017, 20:32:53 UTC | net: qcom/emac: add software control for pause frame mode The EMAC has the option of sending only a single pause frame when flow control is enabled and the RX queue is full. Although sending only one pause frame has little value, this would allow admins to enable automatic flow control without having to worry about the EMAC flooding nearby switches with pause frames if the kernel hangs. The option is enabled by using the single-pause-mode private flag. Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:19:30 UTC |
| 0ab09be | Alex Ng | 20 September 2017, 18:17:35 UTC | hv_netvsc: fix send buffer failure on MTU change If MTU is changed the host would reject the send buffer change. This problem is result of recent change to allow changing send buffer size. Every time we change the MTU, we store the previous net_device section count before destroying the buffer, but we don’t store the previous section size. When we reinitialize the buffer, its size is calculated by multiplying the previous count and previous size. Since we continuously increase the MTU, the host returns us a decreasing count value while the section size is reinitialized to 1728 bytes every time. This eventually leads to a condition where the calculated buf_size is so small that the host rejects it. Fixes: 8b5327975ae1 ("netvsc: allow controlling send/recv buffer size") Signed-off-by: Alex Ng <alexng@microsoft.com> Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:17:16 UTC |
| fe2502e | Cong Wang | 20 September 2017, 16:18:45 UTC | net_sched: remove cls_flower idr on failure Fixes: c15ab236d69d ("net/sched: Change cls_flower to use IDR") Cc: Chris Mi <chrism@mellanox.com> Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 22:13:52 UTC |
| 21f4d5c | Konstantin Khlebnikov | 20 September 2017, 12:46:11 UTC | net_sched/hfsc: fix curve activation in hfsc_change_class() If real-time or fair-share curves are enabled in hfsc_change_class() class isn't inserted into rb-trees yet. Thus init_ed() and init_vf() must be called in place of update_ed() and update_vf(). Remove isn't required because for now curves cannot be disabled. Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 18:56:32 UTC |
| c8e1812 | Konstantin Khlebnikov | 20 September 2017, 12:45:36 UTC | net_sched: always reset qdisc backlog in qdisc_reset() SKB stored in qdisc->gso_skb also counted into backlog. Some qdiscs don't reset backlog to zero in ->reset(), for example sfq just dequeue and free all queued skb. Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Fixes: 2ccccf5fb43f ("net_sched: update hierarchical backlog too") Signed-off-by: David S. Miller <davem@davemloft.net> | 21 September 2017, 18:56:32 UTC |
| 4a704d6 | Linus Torvalds | 21 September 2017, 16:01:03 UTC | Merge tag 'kbuild-fixes-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: "Here are some early Kbuild fixes. The in-kernel firmware was removed during the previous merge window. Since then, some bug reports of broken rpm building are flying in ML. We need to fix it now. Summary: - remove firmware install from rpm-pkg / deb-pkg - fix mismatch between release number and UTS_VERSION for rpm-pkg" * tag 'kbuild-fixes-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kbuild: rpm-pkg: fix version number handling kbuild: deb-pkg: remove firmware package support kbuild: rpm-pkg: delete firmware_install to fix build error | 21 September 2017, 16:01:03 UTC |
| 449cd5d | Linus Torvalds | 21 September 2017, 15:57:50 UTC | Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull misc fixes from Al Viro: "A couple of regression fixes, one for this merge window, one for the previous cycle" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: ipc/shm: Fix order of parameters when calling copy_compat_shmid_to_user iov_iter: fix page_copy_sane for compound pages | 21 September 2017, 15:57:50 UTC |
| d9fde26 | Linus Torvalds | 21 September 2017, 15:55:20 UTC | Merge tag 'mtd/fixes-for-4.14-rc2' of git://git.infradead.org/linux-mtd Pull mtd fixes from Boris Brezillon: "SPI NOR: - Fix the SFDP parsing code (bugs reported by Geert Uytterhoeven) NAND: - Fix a resource leak in the lpc32xx_mlc driver - Fix a build warning in the core" * tag 'mtd/fixes-for-4.14-rc2' of git://git.infradead.org/linux-mtd: mtd: nand: remove unused blockmask variable mtd: nand: lpc32xx_mlc: Fix an error handling path in lpc32xx_nand_probe() mtd: spi-nor: fix DMA unsafe buffer issue in spi_nor_read_sfdp() mtd: spi-nor: Check consistency of the memory size extracted from the SFDP | 21 September 2017, 15:55:20 UTC |
| b6e78a6 | Linus Torvalds | 21 September 2017, 15:52:36 UTC | Merge tag 'drm-fixes-for-v4.14-rc2' of git://people.freedesktop.org/~airlied/linux Pull drm fixes from Dave Airlie: "amdkfd, i915 and exynos fixes. I've ended up on unplanned + planned leave this week, but there were some fixes I decided to dequeue, some amdkfd bits missed the next pull but they are pretty trivial, so I included them. I'm not sure I'll see much else for rc2, lots of people are at XDC" * tag 'drm-fixes-for-v4.14-rc2' of git://people.freedesktop.org/~airlied/linux: drm/exynos/hdmi: Fix unsafe list iteration drm: exynos: include linux/irq.h drm/exynos: Fix suspend/resume support drm/exynos: Fix locking in the suspend/resume paths drm/i915: Remove unused 'in_vbl' from i915_get_crtc_scanoutpos() drm/i915/cnp: set min brightness from VBT Revert "drm/i915/bxt: Disable device ready before shutdown command" drm/i915/bxt: set min brightness from VBT drm/i915: Fix an error handling in 'intel_framebuffer_init()' drm/i915/gvt: Fix incorrect PCI BARs reporting drm/amdkfd: pass queue's mqd when destroying mqd drm/amdkfd: remove memset before memcpy uapi linux/kfd_ioctl.h: only use __u32 and __u64 | 21 September 2017, 15:52:36 UTC |
| 20c29a9 | Linus Torvalds | 21 September 2017, 15:51:03 UTC | Merge tag 'dma-mapping-4.14-2' of git://git.infradead.org/users/hch/dma-mapping Pull dma mapping fix from Christoph Hellwig: "A fix for a fix that went in this merge window from Arnd" * tag 'dma-mapping-4.14-2' of git://git.infradead.org/users/hch/dma-mapping: dma-coherent: fix rmem_dma_device_init regression | 21 September 2017, 15:51:03 UTC |
| 8eba365 | Manuel Lauss | 12 September 2017, 18:36:28 UTC | MIPS: PCI: fix pcibios_map_irq section mismatch Drop the __init from pcibios_map_irq() to make this section mis- match go away: WARNING: vmlinux.o(.text+0x56acd4): Section mismatch in reference from the function pcibios_scanbus() to the function .init.text:pcibios_map_irq() The function pcibios_scanbus() references the function __init pcibios_map_irq(). This is often because pcibios_scanbus lacks a __init annotation or the annotation of pcibios_map_irq is wrong. Run-Tested only on Alchemy. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17267/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> | 21 September 2017, 14:41:20 UTC |
| c22c804 | James Hogan | 19 September 2017, 13:11:22 UTC | MIPS: Fix input modify in __write_64bit_c0_split() The inline asm in __write_64bit_c0_split() modifies the 64-bit input operand by shifting the high register left by 32, and constructing the full 64-bit value in the low register (even on a 32-bit kernel), so if that value is used again it could cause breakage as GCC would assume the registers haven't changed when they have. To quote the GCC extended asm documentation: > Warning: Do not modify the contents of input-only operands (except for > inputs tied to outputs). The compiler assumes that on exit from the > asm statement these operands contain the same values as they had > before executing the statement. Avoid modifying the input by using a temporary variable as an output which is modified instead of the input and not otherwise used. The asm is always __volatile__ so GCC shouldn't optimise it out. The low register of the temporary output is written before the high register of the input is read, so we have two constraint alternatives, one where both use the same registers (for when the input value isn't subsequently used), and one with an early clobber on the output in case the low output uses the same register as the high input. This allows the resulting assembly to remain mostly unchanged. A diff of a MIPS32r6 kernel reveals only three differences, two in relation to write_c0_r10k_diag() in cpu_probe() (register allocation rearranged slightly but otherwise identical), and one in relation to write_c0_cvmmemctl2() in kvm_vz_local_flush_guesttlb_all(), but the octeon CPU is only supported on 64-bit kernels where __write_64bit_c0_split() isn't used so that shouldn't matter in practice. So there currently doesn't appear to be anything broken by this bug. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17315/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> | 21 September 2017, 14:26:42 UTC |
| 9bbe7dc | Arnd Bergmann | 18 September 2017, 15:55:24 UTC | MIPS: MSP71xx: Include asm/setup.h msp71xx_defconfig can not be built at the in v4.14-rc1 arch/mips/pmcs-msp71xx/msp_smp.c:72:2: error: implicit declaration of function 'set_vi_handler' [-Werror=implicit-function-declaration] I don't know what caused the regression, but including the right header is the obvious fix. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17309/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> | 21 September 2017, 14:15:17 UTC |
| b537ca6 | Tyrel Datwyler | 20 September 2017, 21:02:52 UTC | powerpc/pseries: Fix parent_dn reference leak in add_dt_node() A reference to the parent device node is held by add_dt_node() for the node to be added. If the call to dlpar_configure_connector() fails add_dt_node() returns ENOENT and that reference is not freed. Add a call to of_node_put(parent_dn) prior to bailing out after a failed dlpar_configure_connector() call. Fixes: 8d5ff320766f ("powerpc/pseries: Make dlpar_configure_connector parent node aware") Cc: stable@vger.kernel.org # v3.12+ Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> | 21 September 2017, 09:33:16 UTC |
| 087ff6a | Tyrel Datwyler | 20 September 2017, 21:02:51 UTC | powerpc/pseries: Fix "OF: ERROR: Bad of_node_put() on /cpus" during DLPAR Commit 215ee763f8cb ("powerpc: pseries: remove dlpar_attach_node dependency on full path") reworked dlpar_attach_node() to no longer look up the parent node "/cpus", but instead to have the parent node passed by the caller in the function parameter list. As a result dlpar_attach_node() is no longer responsible for freeing the reference to the parent node. However, commit 215ee763f8cb failed to remove the of_node_put(parent) call in dlpar_attach_node(), or to take into account that the reference to the parent in the caller dlpar_cpu_add() needs to be held until after dlpar_attach_node() returns. As a result doing repeated cpu add/remove dlpar operations will eventually result in the following error: OF: ERROR: Bad of_node_put() on /cpus CPU: 0 PID: 10896 Comm: drmgr Not tainted 4.13.0-autotest #1 Call Trace: dump_stack+0x15c/0x1f8 (unreliable) of_node_release+0x1a4/0x1c0 kobject_put+0x1a8/0x310 kobject_del+0xbc/0xf0 __of_detach_node_sysfs+0x144/0x210 of_detach_node+0xf0/0x180 dlpar_detach_node+0xc4/0x120 dlpar_cpu_remove+0x280/0x560 dlpar_cpu_release+0xbc/0x1b0 arch_cpu_release+0x6c/0xb0 cpu_release_store+0xa0/0x100 dev_attr_store+0x68/0xa0 sysfs_kf_write+0xa8/0xf0 kernfs_fop_write+0x2cc/0x400 __vfs_write+0x5c/0x340 vfs_write+0x1a8/0x3d0 SyS_write+0xa8/0x1a0 system_call+0x58/0x6c Fix the issue by removing the of_node_put(parent) call from dlpar_attach_node(), and ensuring that the reference to the parent node is properly held and released by the caller dlpar_cpu_add(). Fixes: 215ee763f8cb ("powerpc: pseries: remove dlpar_attach_node dependency on full path") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> [mpe: Add a comment in the code and frob the change log slightly] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> | 21 September 2017, 09:30:53 UTC |
| 3e77ade | Benjamin Herrenschmidt | 07 September 2017, 06:35:40 UTC | powerpc/eeh: Create PHB PEs after EEH is initialized Otherwise we end up not yet having computed the right diag data size on powernv where EEH initialization is delayed, thus causing memory corruption later on when calling OPAL. Fixes: 5cb1f8fdddb7 ("powerpc/powernv/pci: Dynamically allocate PHB diag data") Cc: stable@vger.kernel.org # v4.13+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Russell Currey <ruscur@russell.cc> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> | 21 September 2017, 04:56:00 UTC |
| 58aff0a | Will Deacon | 18 September 2017, 16:47:38 UTC | ipc/shm: Fix order of parameters when calling copy_compat_shmid_to_user Commit 553f770ef71b ("ipc: move compat shmctl to native") moved the compat IPC syscall handling into ipc/shm.c and refactored the struct accessors in the process. Unfortunately, the call to copy_compat_shmid_to_user when handling a compat {IPC,SHM}_STAT command gets the arguments the wrong way round, passing a kernel stack address as the user buffer (destination) and the user buffer as the kernel stack address (source). This patch fixes the parameter ordering so the buffers are accessed correctly. Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> | 21 September 2017, 03:27:48 UTC |
| a90bcb8 | Petar Penkov | 29 August 2017, 18:20:32 UTC | iov_iter: fix page_copy_sane for compound pages Issue is that if the data crosses a page boundary inside a compound page, this check will incorrectly trigger a WARN_ON. To fix this, compute the order using the head of the compound page and adjust the offset to be relative to that head. Fixes: 72e809ed81ed ("iov_iter: sanity checks for copy to/from page primitives") Signed-off-by: Petar Penkov <ppenkov@google.com> CC: Al Viro <viro@zeniv.linux.org.uk> CC: Eric Dumazet <edumazet@google.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> | 21 September 2017, 03:27:48 UTC |
| 0603c96 | Steve French | 21 September 2017, 00:57:18 UTC | SMB: Validate negotiate (to protect against downgrade) even if signing off As long as signing is supported (ie not a guest user connection) and connection is SMB3 or SMB3.02, then validate negotiate (protect against man in the middle downgrade attacks). We had been doing this only when signing was required, not when signing was just enabled, but this more closely matches recommended SMB3 behavior and is better security. Suggested by Metze. Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Jeremy Allison <jra@samba.org> Acked-by: Stefan Metzmacher <metze@samba.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> | 21 September 2017, 00:57:18 UTC |
| f5c4ba8 | Shu Wang | 08 September 2017, 10:48:33 UTC | cifs: release auth_key.response for reconnect. There is a race that cause cifs reconnect in cifs_mount, - cifs_mount - cifs_get_tcp_session - [ start thread cifs_demultiplex_thread - cifs_read_from_socket: -ECONNABORTED - DELAY_WORK smb2_reconnect_server ] - cifs_setup_session - [ smb2_reconnect_server ] auth_key.response was allocated in cifs_setup_session, and will release when the session destoried. So when session re- connect, auth_key.response should be check and released. Tested with my system: CIFS VFS: Free previous auth_key.response = ffff8800320bbf80 A simple auth_key.response allocation call trace: - cifs_setup_session - SMB2_sess_setup - SMB2_sess_auth_rawntlmssp_authenticate - build_ntlmssp_auth_blob - setup_ntlmv2_rsp Signed-off-by: Shu Wang <shuwang@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> | 20 September 2017, 23:46:23 UTC |
| 9418333 | Shu Wang | 07 September 2017, 08:03:27 UTC | cifs: release cifs root_cred after exit_cifs memory leak was found by kmemleak. exit_cifs_spnego should be called before cifs module removed, or cifs root_cred will not be released. kmemleak report: unreferenced object 0xffff880070a3ce40 (size 192): backtrace: kmemleak_alloc+0x4a/0xa0 kmem_cache_alloc+0xc7/0x1d0 prepare_kernel_cred+0x20/0x120 init_cifs_spnego+0x2d/0x170 [cifs] 0xffffffffc07801f3 do_one_initcall+0x51/0x1b0 do_init_module+0x60/0x1fd load_module+0x161e/0x1b60 SYSC_finit_module+0xa9/0x100 SyS_finit_module+0xe/0x10 Signed-off-by: Shu Wang <shuwang@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> | 20 September 2017, 23:46:16 UTC |
| 4d61eda | Colin Ian King | 19 September 2017, 15:27:39 UTC | CIFS: make arrays static const, reduces object code size Don't populate the read-only arrays types[] on the stack, instead make them both static const. Makes the object code smaller by over 200 bytes: Before: text data bss dec hex filename 111503 37696 448 149647 2488f fs/cifs/file.o After: text data bss dec hex filename 111140 37856 448 149444 247c4 fs/cifs/file.o Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> | 20 September 2017, 23:46:10 UTC |
| 6cc4083 | David S. Miller | 20 September 2017, 23:15:40 UTC | Merge branch 'hns3-tm-fixes' Yunsheng Lin says: ==================== TM related bugfixes for the HNS3 Ethernet Driver This patch set contains a few bugfixes related to hclge_tm module. ==================== Signed-off-by: David S. Miller <davem@davemloft.net> | 20 September 2017, 23:15:40 UTC |
| c5795c5 | Yunsheng Lin | 20 September 2017, 10:52:58 UTC | net: hns3: Fix for pri to tc mapping in TM Current mapping between pri and tc is one to one, so user can't map multi priorities to the same tc. This patch changes the mapping to many to one. Fixes: 848440544b41f ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 20 September 2017, 23:15:40 UTC |
| 68ece54 | Yunsheng Lin | 20 September 2017, 10:52:57 UTC | net: hns3: Fix for setting rss_size incorrectly rss_size is 1, 2, 4, 8, 16, 32, 64, 128, but acutal tc queue size can be any u16 less than 128. If tc queue size is 5, we set the rss_size to 8, indirection table will be used to limit the size of actual queue size. It may cause dropping of receiving packet in hardware if rss_size is not set correctly. For now, each TC has the same rss size. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 20 September 2017, 23:15:40 UTC |
| c472633 | Yunsheng Lin | 20 September 2017, 10:52:56 UTC | net: hns3: Fix typo error for feild in hclge_tm This patch fixes a typo error for feild, which should be field. Fixes: 848440544b41f ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 20 September 2017, 23:15:40 UTC |
| d602a52 | Yunsheng Lin | 20 September 2017, 10:52:55 UTC | net: hns3: Fix for rx priv buf allocation when DCB is not supported When hdev doesn't support DCB, rx private buffer is not allocated, otherwise there is not enough buffer for rx shared buffer, causing buffer allocation process to fail. This patch fixes by checking the dcb capability in hclge_rx_buffer_calc. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 20 September 2017, 23:15:39 UTC |
| b8c8bf4 | Yunsheng Lin | 20 September 2017, 10:52:54 UTC | net: hns3: Fix for rx_priv_buf_alloc not setting rx shared buffer rx_priv_buf_alloc is used to tell hardware how much buffer is used for rx direction, right now only the private buffer is assigned. For ae_dev that doesn't support DCB, private rx buffer is assigned to zero, only shared rx buffer is used. So not setting the shared rx buffer cause dropping of packet in SSU. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | 20 September 2017, 23:15:39 UTC |
