Revision 71bfc7a7c73eaf1f99e309dba60822ba050e3ec5 authored by Hannes Eder on 05 March 2009, 15:10:56 UTC, committed by Bartlomiej Zolnierkiewicz on 05 March 2009, 15:10:56 UTC
Fix this sparse warnings:
  drivers/ide/ide-disk_proc.c:130:11: warning: Using plain integer as NULL pointer
  drivers/ide/ide-floppy_proc.c:32:11: warning: Using plain integer as NULL pointer
  drivers/ide/ide-proc.c:234:11: warning: Using plain integer as NULL pointer
  drivers/ide/ide-tape.c:2141:11: warning: Using plain integer as NULL pointer

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Cc: trivial@kernel.org
Cc: kernel-janitors@vger.kernel.org
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
1 parent e0c6dcd
Raw File
Kconfig
# sound/Config.in
#

menuconfig SOUND
	tristate "Sound card support"
	depends on HAS_IOMEM
	help
	  If you have a sound card in your computer, i.e. if it can say more
	  than an occasional beep, say Y.  Be sure to have all the information
	  about your sound card and its configuration down (I/O port,
	  interrupt and DMA channel), because you will be asked for it.

	  You want to read the Sound-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>. General information about
	  the modular sound system is contained in the files
	  <file:Documentation/sound/oss/Introduction>.  The file
	  <file:Documentation/sound/oss/README.OSS> contains some slightly
	  outdated but still useful information as well.  Newer sound
	  driver documentation is found in <file:Documentation/sound/alsa/*>.

	  If you have a PnP sound card and you want to configure it at boot
	  time using the ISA PnP tools (read
	  <http://www.roestock.demon.co.uk/isapnptools/>), then you need to
	  compile the sound card support as a module and load that module
	  after the PnP configuration is finished.  To do this, choose M here
	  and read <file:Documentation/sound/oss/README.modules>; the module
	  will be called soundcore.

if SOUND

config SOUND_OSS_CORE
	bool
	default n

source "sound/oss/dmasound/Kconfig"

if !M68K

menuconfig SND
	tristate "Advanced Linux Sound Architecture"
	help
	  Say 'Y' or 'M' to enable ALSA (Advanced Linux Sound Architecture),
	  the new base sound system.

	  For more information, see <http://www.alsa-project.org/>

if SND

source "sound/core/Kconfig"

source "sound/drivers/Kconfig"

source "sound/isa/Kconfig"

source "sound/pci/Kconfig"

source "sound/ppc/Kconfig"

source "sound/aoa/Kconfig"

source "sound/arm/Kconfig"

source "sound/spi/Kconfig"

source "sound/mips/Kconfig"

source "sound/sh/Kconfig"

# the following will depend on the order of config.
# here assuming USB is defined before ALSA
source "sound/usb/Kconfig"

# the following will depend on the order of config.
# here assuming PCMCIA is defined before ALSA
source "sound/pcmcia/Kconfig"

source "sound/sparc/Kconfig"

source "sound/parisc/Kconfig"

source "sound/soc/Kconfig"

endif # SND

menuconfig SOUND_PRIME
	tristate "Open Sound System (DEPRECATED)"
	select SOUND_OSS_CORE
	help
	  Say 'Y' or 'M' to enable Open Sound System drivers.

if SOUND_PRIME

source "sound/oss/Kconfig"

endif # SOUND_PRIME

endif # !M68K

endif # SOUND

# AC97_BUS is used from both sound and ucb1400
config AC97_BUS
	tristate
	help
	  This is used to avoid config and link hard dependencies between the
	  sound subsystem and other function drivers completely unrelated to
	  sound although they're sharing the AC97 bus. Concerned drivers
	  should "select" this.

back to top