Revision 810198bc9c109489dfadc57131c5183ce6ad2d7d authored by Rajashekhara, Sudhakar on 12 July 2011, 10:28:53 UTC, committed by Sekhar Nori on 07 September 2011, 08:53:01 UTC
DA850/OMAP-L138 EMAC driver uses random mac address instead of a fixed one because the mac address is not stuffed into EMAC platform data. This patch provides a function which reads the mac address stored in SPI flash (registered as MTD device) and populates the EMAC platform data. The function which reads the mac address is registered as a callback which gets called upon addition of MTD device. NOTE: In case the MAC address stored in SPI flash is erased, follow the instructions at [1] to restore it. [1] http://processors.wiki.ti.com/index.php/GSG:_OMAP-L138_DVEVM_Additional_Procedures#Restoring_MAC_address_on_SPI_Flash Modifications in v2: Guarded registering the mtd_notifier only when MTD is enabled. Earlier this was handled using mtd_has_partitions() call, but this has been removed in Linux v3.0. Modifications in v3: a. Guarded da850_evm_m25p80_notify_add() function and da850evm_spi_notifier structure with CONFIG_MTD macros. b. Renamed da850_evm_register_mtd_user() function to da850_evm_setup_mac_addr() and removed the struct mtd_notifier argument to this function. c. Passed the da850evm_spi_notifier structure to register_mtd_user() function. Modifications in v4: Moved the da850_evm_setup_mac_addr() function within the first CONFIG_MTD ifdef construct. Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Cc: stable@kernel.org
1 parent ddf2835
VGA-softcursor.txt
Software cursor for VGA by Pavel Machek <pavel@atrey.karlin.mff.cuni.cz>
======================= and Martin Mares <mj@atrey.karlin.mff.cuni.cz>
Linux now has some ability to manipulate cursor appearance. Normally, you
can set the size of hardware cursor (and also work around some ugly bugs in
those miserable Trident cards--see #define TRIDENT_GLITCH in drivers/video/
vgacon.c). You can now play a few new tricks: you can make your cursor look
like a non-blinking red block, make it inverse background of the character it's
over or to highlight that character and still choose whether the original
hardware cursor should remain visible or not. There may be other things I have
never thought of.
The cursor appearance is controlled by a "<ESC>[?1;2;3c" escape sequence
where 1, 2 and 3 are parameters described below. If you omit any of them,
they will default to zeroes.
Parameter 1 specifies cursor size (0=default, 1=invisible, 2=underline, ...,
8=full block) + 16 if you want the software cursor to be applied + 32 if you
want to always change the background color + 64 if you dislike having the
background the same as the foreground. Highlights are ignored for the last two
flags.
The second parameter selects character attribute bits you want to change
(by simply XORing them with the value of this parameter). On standard VGA,
the high four bits specify background and the low four the foreground. In both
groups, low three bits set color (as in normal color codes used by the console)
and the most significant one turns on highlight (or sometimes blinking--it
depends on the configuration of your VGA).
The third parameter consists of character attribute bits you want to set.
Bit setting takes place before bit toggling, so you can simply clear a bit by
including it in both the set mask and the toggle mask.
Examples:
=========
To get normal blinking underline, use: echo -e '\033[?2c'
To get blinking block, use: echo -e '\033[?6c'
To get red non-blinking block, use: echo -e '\033[?17;0;64c'
Computing file changes ...
