| 840658b | Tom Rini | 05 July 2021, 15:11:28 UTC | Prepare v2021.07 Signed-off-by: Tom Rini <trini@konsulko.com> | 05 July 2021, 15:11:28 UTC |
| 09576cd | Tom Rini | 02 July 2021, 22:56:46 UTC | Merge tag 'u-boot-amlogic-20210703' of https://source.denx.de/u-boot/custodians/u-boot-amlogic - configs: libretech: set SPI mode to 0 to fix SPI NOR Flash probe | 02 July 2021, 22:56:46 UTC |
| 8c6d8c3 | Da Xue | 02 July 2021, 21:11:40 UTC | configs: libretech: set SPI mode to 0 Kconfig defaults to mode 3 if CONFIG_SF_DEFAULT_MODE is not set. It becomes an issue since meson_spifc does not support SPI_CPHA. Needed after commit e2e95e5e25 ("spi: Update speed/mode on change"). Fixes: e2e95e5e25 ("spi: Update speed/mode on change") Signed-off-by:Da Xue <da@libre.computer> [narmstrong: reformated commit reference & added Fixes tag] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> | 02 July 2021, 21:59:27 UTC |
| 62c7e40 | Tom Rini | 02 July 2021, 19:04:07 UTC | Merge tag 'efi-2021-07-rc6' of https://source.denx.de/u-boot/custodians/u-boot-efi Pull request for efi-2021-07-rc6 Bug fixes: * improve specification compliance of UEFI capsule updates * allow capsule update on-disk without checking OsIndications * provide parameter checks for QueryVariableInfo() | 02 July 2021, 19:04:07 UTC |
| 760d2f9 | Da Xue | 02 July 2021, 16:32:43 UTC | autoboot: fix MENUKEY replace CONFIG_AUTOBOOT_USE_MENUKEY with CONFIG_AUTOBOOT_MENUKEY Signed-off-by: Da Xue <da@libre.computer> | 02 July 2021, 19:03:53 UTC |
| 0fa5020 | Ilias Apalodimas | 29 June 2021, 04:55:51 UTC | efi_loader: Allow capsule update on-disk without checking OsIndications Although U-Boot supports capsule update on-disk, it's lack of support for SetVariable at runtime prevents applications like fwupd from using it. In order to perform the capsule update on-disk the spec says that the OS must copy the capsule to the \EFI\UpdateCapsule directory and set a bit in the OsIndications variable. The firmware then checks for the EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED bit in OsIndications variable, which is set by the submitter to trigger processing of the capsule on the next reboot. Let's add a config option which ignores the bit and just relies on the capsule being present. Since U-Boot deletes the capsule while processing it, we won't end up applying it multiple times. Note that this is allowed for all capsules. In the future, once authenticated capsules are fully supported, we can limit the functionality to those only. Signed-off-by: apalos <ilias.apalodimas@linaro.org> Reword Kconfig description. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 02 July 2021, 16:29:06 UTC |
| 149108a | Heinrich Schuchardt | 29 June 2021, 11:33:09 UTC | efi_loader: clear OsIndications After each reboot we must clear flag EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED in variable OsIndications. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 02 July 2021, 07:37:01 UTC |
| 417a3c2 | Masami Hiramatsu | 30 June 2021, 15:49:48 UTC | efi_loader: Improve the parameter check for QueryVariableInfo() Improve efi_query_variable_info() to check the parameter settings and return correct error code according to the UEFI Specification 2.9, and the Self Certification Test (SCT) II Case Specification, June 2017, chapter 4.1.4 QueryVariableInfo(). Reported-by: Kazuhiko Sakamoto <sakamoto.kazuhiko@socionext.com> Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 02 July 2021, 07:37:01 UTC |
| abd62e4 | Heinrich Schuchardt | 29 June 2021, 08:09:14 UTC | efi_loader: missing parentheses in query_console_size After if we should use parentheses to keep the code readable. Fixes: a95f4c885991 ("efi_loader: NULL dereference in EFI console") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 02 July 2021, 07:37:01 UTC |
| 6e0184b | Ilias Apalodimas | 22 June 2021, 14:38:53 UTC | efi_loader: Always install FMPs We only install FMPs if a CapsuleUpdate is requested. Since we now have an ESRT table which relies on FMPs to build the required information, it makes more sense to unconditionally install them. This will allow userspace applications (e.g fwupd) to make use of the ERST and provide us with files we can use to run CapsuleUpdate on-disk Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 02 July 2021, 07:37:01 UTC |
| b891ff1 | Ilias Apalodimas | 22 June 2021, 14:38:52 UTC | efi_loader: Force a single FMP instance per hardware store Chapter 23 of the EFI spec (rev 2.9) says: "A specific updatable hardware firmware store must be represented by exactly one FMP instance". This is not the case for us, since both of our FMP protocols can be installed at the same time because they are controlled by a single 'dfu_alt_info' env variable. So make the config options depend on each other and allow the user to install one of them at any given time. If we fix the meta-data provided by the 'dfu_alt_info' in the future, to hint about the capsule type (fit or raw) we can revise this and enable both FMPs to be installed, as long as they target different firmware hardware stores Note that we are not using a Kconfig 'choice' on purpose, since we want to allow both of those to be installed and tested in sandbox Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 02 July 2021, 07:37:01 UTC |
| 3ef7722 | Masami Hiramatsu | 22 June 2021, 14:38:51 UTC | efi: Fix to use null handle to create new handle for efi_fmp_raw When running the efidebug capsule disk-update command, the efi_fmp_raw protocol installation fails with 2 (EFI_INVALID_PARAMETER) as below. This is because the code passes efi_root instead of the handle local var. => efidebug capsule disk-update EFI: Call: efi_install_multiple_protocol_interfaces( &handle, &efi_guid_firmware_management_protocol, &efi_fmp_fit, NULL) EFI: Entry efi_install_multiple_protocol_interfaces(00000000fbaf5988) EFI: Call: efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface) EFI: Entry efi_install_protocol_interface(00000000fbaf5988, 86c77a67-0b97-4633-a187-49104d0685c7, 0, 00000000fbfa6ee8) EFI: new handle 00000000fbb37520 EFI: Exit: efi_install_protocol_interface: 0 EFI: 0 returned by efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface) EFI: Exit: efi_install_multiple_protocol_interfaces: 0 EFI: 0 returned by efi_install_multiple_protocol_interfaces( &handle, &efi_guid_firmware_management_protocol, &efi_fmp_fit, NULL) EFI: Call: efi_install_multiple_protocol_interfaces( &efi_root, &efi_guid_firmware_management_protocol, &efi_fmp_raw, NULL) EFI: Entry efi_install_multiple_protocol_interfaces(00000000fbfec648) EFI: Call: efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface) EFI: Entry efi_install_protocol_interface(00000000fbfec648, 86c77a67-0b97-4633-a187-49104d0685c7, 0, 00000000fbfa6f18) EFI: handle 00000000fbaf8520 EFI: Exit: efi_install_protocol_interface: 2 EFI: 2 returned by efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface) EFI: Exit: efi_install_multiple_protocol_interfaces: 2 EFI: 2 returned by efi_install_multiple_protocol_interfaces( &efi_root, &efi_guid_firmware_management_protocol, &efi_fmp_raw, NULL) Command failed, result=1 To fix this issue, pass the handle local var which is set NULL right before installing efi_fmp_raw as same as the installing efi_fmp_fit. (In both cases, the local reference to the handle will be just discarded) Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 02 July 2021, 07:37:01 UTC |
| b7ad721 | Tom Rini | 30 June 2021, 17:09:49 UTC | Revert "TEST: USB_HOST not USB" This reverts commit 4e1903a645453deab5ec5dd1cf4f0061469b99c3. This local commit was not intended to be pushed out. Signed-off-by: Tom Rini <trini@konsulko.com> | 30 June 2021, 17:10:02 UTC |
| 4e1903a | Tom Rini | 30 June 2021, 15:38:52 UTC | TEST: USB_HOST not USB Signed-off-by: Tom Rini <trini@konsulko.com> | 30 June 2021, 15:38:52 UTC |
| e2e95e5 | Marek Vasut | 10 June 2021, 12:00:00 UTC | spi: Update speed/mode on change The spi_get_bus_and_cs() may be called on the same bus and chipselect with different frequency or mode. This is valid usecase, but the code fails to notify the controller of such a configuration change. Call spi_set_speed_mode() in case bus frequency or bus mode changed to let the controller update the configuration. The problem can easily be triggered using the sspi command: => sspi 0:0@1000 => sspi 0:0@2000 Without this patch, both transfers happen at 1000 Hz. With this patch, the later transfer happens correctly at 2000 Hz. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> | 30 June 2021, 12:06:30 UTC |
| 605cbcb | Tom Rini | 29 June 2021, 15:25:39 UTC | Merge tag 'efi-2021-07-rc5-2' of https://source.denx.de/u-boot/custodians/u-boot-efi Pull request for efi-2021-07-rc5-2 Documentation: * man-page for askenv bug fixes * correct display of BootOrder in efidebug command * do not allow TPL_HIGH_LEVEL for CreateEvent(Ex) * correct handling of unknown properties in SMBIOS tables | 29 June 2021, 15:25:39 UTC |
| 3ef4572 | Tom Rini | 28 June 2021, 19:38:55 UTC | Prepare v2021.07-rc5 Signed-off-by: Tom Rini <trini@konsulko.com> | 28 June 2021, 19:38:55 UTC |
| 534f0fb | Kunihiko Hayashi | 15 June 2021, 06:33:02 UTC | arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y If both POSITION_INDEPENDENT and SYS_RELOC_GD_ENV_ADDR are enabled, wherever original env is placed anywhere, it should be relocated to the right address. Relocation offset gd->reloc_off is calculated with SYS_TEXT_BASE in setup_reloc() and env address gd->env_addr is relocated by the offset in initr_reloc_global_data(). gd->env_addr = (orig env) + gd->reloc_off = (orig env) + (gd->relocaddr - SYS_TEXT_BASE) However, SYS_TEXT_BASE isn't always runtime base address when POSITION_INDEPENDENT is enabled. So the relocated env_addr might point to wrong address. For example, if SYS_TEXT_BASE is zero, gd->env_addr is out of memory location and memory exception will occur. There is a difference between linked address such as SYS_TEXT_BASE and runtime base address. In _main, the difference is calculated as "run-vs-link" offset. The env_addr should also be added to the offset to fix the address. gd->env_addr = (orig env) + ("run-vs-link" offset) + gd->reloc_off = (orig env) + (SYS_TEXT_BASE - _start) + (gd->relocaddr - SYS_TEXT_BASE) = (orig env) + (gd->relocaddr - _start) Cc: Marek Vasut <marex@denx.de> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de> | 28 June 2021, 18:47:10 UTC |
| 70e8066 | Ilias Apalodimas | 10 June 2021, 09:33:15 UTC | smbios: Fix SMBIOS tables Commit e4f8e543f1a9("smbios: Drop the unused Kconfig options") break SMBIOS tables. The reason is that the patch drops the Kconfig options *after* removing the code using them, but that changes the semantics of the code completely. Prior to the change a non NULL value was used in the 'product' and 'manufacturer ' fields. Chapter 6.2 of the DMTF spec requires Manufacturer and Product Name to be non-null on some of the tables. So let's add sane defaults for Type1/2/3. * Before the patchset: <snip> Handle 0x0002, DMI type 2, 14 bytes Base Board Information Manufacturer: Not Specified Product Name: Not Specified Version: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Features: Board is a hosting board Location In Chassis: Not Specified Chassis Handle: 0x0000 Type: Motherboard Invalid entry length (0). DMI table is broken! Stop. * After the patchset: <snip> Handle 0x0005, DMI type 32, 11 bytes System Boot Information Status: No errors detected Handle 0x0006, DMI type 127, 4 bytes End Of Table Fixes: e4f8e543f1a9 ("smbios: Drop the unused Kconfig options") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> | 28 June 2021, 17:57:13 UTC |
| ff19230 | Ilias Apalodimas | 09 June 2021, 15:14:47 UTC | smbios: Fix BIOS Characteristics Extension Byte 2 We currently define the EFI support of an SMBIOS table as the third bit of "BIOS Characteristics Extension Byte 1". The latest DMTF spec defines it on "BIOS Characteristics Extension Byte 2". Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Remove superfluous assignment. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 28 June 2021, 17:57:13 UTC |
| a86ed41 | Adarsh Babu Kalepalli | 11 June 2021, 14:15:11 UTC | doc/usage: cmd-usage help file for askenv help file for using askenv cmd is created. It provides description on the command purpose, description of arguments, couple of examples (illustrating command usage), configuration parameter and possible return values. Signed-off-by: Adarsh Babu Kalepalli <opensource.kab@gmail.com> Add missing entry in doc/usage/index.rst. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 28 June 2021, 17:57:13 UTC |
| 8c6532d | Heinrich Schuchardt | 10 June 2021, 10:13:52 UTC | smbios: convert function descriptions to Sphinx style Use 'Return:' instead of '@return:'. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 28 June 2021, 17:57:13 UTC |
| 2b8723c | Heinrich Schuchardt | 11 June 2021, 22:01:44 UTC | efidebug: correct display of BootOrder Display the number of the boot option and not its index. Fixes: 2ecee31017bf ("efi_loader: use efi_create_indexed_name()") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 28 June 2021, 17:57:13 UTC |
| 7891fe6 | Heinrich Schuchardt | 10 June 2021, 21:10:52 UTC | efi_loader: TPL_HIGH_LEVEL not allowed for CreateEvent According to chapter 7.1 "Event, Timer, and Task Priority Services" TPL_HIGH_LEVEL should not be exposed to applications and drivers. According to the discussion with EDK II contributors this implies that CreateEvent() shall not allow to create events with TPL_HIGH_LEVEL. Cc: Samer El-Haj-Mahmoud <Samer.El-Haj-Mahmoud@arm.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Samer El-Haj-Mahmoud <Samer.El-Haj-Mahmoud@arm.com> | 28 June 2021, 17:57:13 UTC |
| 2bba780 | Tom Rini | 28 June 2021, 14:17:29 UTC | configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> | 28 June 2021, 14:17:29 UTC |
| 4d8c21d | Tom Rini | 25 June 2021, 17:33:47 UTC | Merge tag 'u-boot-imx-20210625' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2021.07 ----------------- CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7903 | 25 June 2021, 17:33:47 UTC |
| 1b044fd | Tom Rini | 25 June 2021, 01:18:22 UTC | Merge https://source.denx.de/u-boot/custodians/u-boot-sh - Beacon board fix, for this release. | 25 June 2021, 01:18:22 UTC |
| 0e1819f | Tom Rini | 25 June 2021, 01:17:49 UTC | Merge https://source.denx.de/u-boot/custodians/u-boot-usb - A few easy MX7 EHCI USB fixes, for this release. | 25 June 2021, 01:17:49 UTC |
| 4822114 | Fabio Estevam | 20 June 2021, 15:00:52 UTC | usb: ehci-mx6: Do not fail when 'reg' is not found Unlike imx6, on imx7 the USB PHY is described as: usbphynop1: usbphynop1 { compatible = "usb-nop-xceiv"; clocks = <&clks IMX7D_USB_PHY1_CLK>; clock-names = "main_clk"; #phy-cells = <0>; }; which does not have the 'reg' property. Do not return an error when the 'reg' property is not found for the USB PHY. This fixes USB gadget regression on a imx7s-warp board. Successfully tested the "ums 0 mmc 0" command on two boards: imx7s-warp and imx6dl-pico-pi. Signed-off-by: Fabio Estevam <festevam@denx.de> | 24 June 2021, 18:23:23 UTC |
| ec326b9 | Fabio Estevam | 20 June 2021, 15:00:51 UTC | usb: ehci-mx6: Move fdtdec_get_alias_seq() inside the CONFIG_MX6 On a imx7s-warp board the fdtdec_get_alias_seq() function always fails. As priv->portnr is only used on i.MX6, move fdtdec_get_alias_seq() inside the CONFIG_MX6 block. Signed-off-by: Fabio Estevam <festevam@denx.de> | 24 June 2021, 18:23:23 UTC |
| 12ef801 | Adam Ford | 24 June 2021, 17:52:11 UTC | ARM: rmobile: beacon: Set CONFIG_RZ_G2 on Beacon boards The board detection is incorrectly stating it's an rcar3 variant instead of an RZ/G2 variant on all the r8a774*1_beacon boards. Set the flag to correctly display as RZ/G2[M/N/H] Signed-off-by: Adam Ford <aford173@gmail.com> | 24 June 2021, 18:22:31 UTC |
| fcf3981 | Tom Rini | 23 June 2021, 12:46:26 UTC | Merge https://source.denx.de/u-boot/custodians/u-boot-x86 - x86: Discard .note.gnu.property sections - nvme: Skip block device creation for inactive namespaces - nvme: Convert NVMe doc to reST, and various minor fixes | 23 June 2021, 12:46:26 UTC |
| c3a095d | Tom Rini | 23 June 2021, 12:45:29 UTC | Merge tag 'mmc-2021-6-22' of https://source.denx.de/u-boot/custodians/u-boot-mmc - Revert fsl_esdhc_imx using VENDORSPEC_FRC_SDCLK_ON - Fix data read for dw_mmc - Increase minimum bus freq for mtk-sd - Minor cleanup | 23 June 2021, 12:45:29 UTC |
| 6fc0a2f | Tom Rini | 23 June 2021, 12:45:09 UTC | Merge branch '2021-06-22-assorted-fixes' - Assorted minor bugfixes | 23 June 2021, 12:45:09 UTC |
| b2710fa | Andy Shevchenko | 10 June 2021, 15:08:42 UTC | test: Include /sbin to the PATH when creating file system On some distributions the mkfs is under /sbin and /sbin is not set for mere users. Include /sbin to the PATH when creating file system, so that users won't get a scary traceback from Python. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> | 23 June 2021, 12:45:03 UTC |
| af8e2d4 | Jaehoon Chung | 14 June 2021, 22:16:36 UTC | MAINTAINER, git-mailrc: Update the mmc maintainer Update to me as co-maintainer with Peng. Additionally, update the mmc alias in git-mailrc. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> | 23 June 2021, 12:45:03 UTC |
| 076c7bf | Tom Rini | 03 June 2021, 13:39:02 UTC | global_data: Ensure we have <config.h> when symbols are not in Kconfig yet All symbols that are defined in Kconfig will always be defined (or not) prior to preprocessing due to the -include directive while building. However, symbols which are not yet migrated will only be defined (or not) once the board config.h is included, via <config.h>. While the end goal must be to migrate all symbols, today we have cases where the size of gd will get mismatched within the build, based on include order. Mitigate this by making sure that any <asm/global_data.h> that uses symbols not in Kconfig does start with <config.h>. Remove this when not needed. Cc: Alexey Brodkin <alexey.brodkin@synopsys.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: Huan Wang <alison.wang@nxp.com> Cc: Angelo Dureghello <angelo@sysam.it> Cc: Rick Chen <rick@andestech.com> Signed-off-by: Tom Rini <trini@konsulko.com> | 23 June 2021, 12:45:03 UTC |
| 640e2cd | Tom Rini | 03 June 2021, 13:39:01 UTC | socfpga64: Do not define CONFIG_SYS_MEM_RESERVE_SECURE to 0 Based on the comment in socfpga_soc64_common.h, the intention is for CONFIG_SYS_MEM_RESERVE_SECURE to be unused. However, in the code we do: ... and that will evaluate to true. This leads to unwanted code being compiled. Further, as CONFIG_SYS_MEM_RESERVE_SECURE has not been migrated to Kconfig, this leads to a mismatch in the size of gd depending on if we have or have not also had <configs/BOARD.h> also included yet. Remove the define as it's not needed. Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Chee Hong Ang <chee.hong.ang@intel.com> Cc: Dalon Westergreen <dalon.westergreen@intel.com> Signed-off-by: Tom Rini <trini@konsulko.com> | 23 June 2021, 12:45:03 UTC |
| 8f0f26e | Tom Rini | 03 June 2021, 13:39:00 UTC | Revert "powerpc: fix regression in arch_initr_trap()" With the changes in commit 588efcdd72fc ("powerpc: Don't use relative include for config.h in global_data.h") fixing the root of the problem, we no longer need this re-inclusion. This reverts commit f6c0d365d3e8ee8e4fd3ebe2ed957c2bca9d3328. Cc: Matt Merhar <mattmerhar@protonmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> | 23 June 2021, 12:45:03 UTC |
| 8b95dea | Tom Rini | 03 June 2021, 13:38:59 UTC | powerpc: Don't use relative include for config.h in global_data.h As there is an arch/powerpc/include/asm/config.h file using "" to get config.h here can lead to using that rather than include/config.h. This in turn can lead to a mismatch in the size of gd. Cc: Matt Merhar <mattmerhar@protonmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Matt Merhar <mattmerhar@protonmail.com> | 23 June 2021, 12:45:03 UTC |
| 5ad9220 | Heinrich Schuchardt | 29 May 2021, 11:18:00 UTC | malloc: add SPDX license identifiers The original code is in the public domain. Licenses/README states that the general license for U-Boot is GPL 2.0+. So we can mark the malloc code as GPL 2.0+ too. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 23 June 2021, 12:45:03 UTC |
| f68d5a6 | Bin Meng | 22 June 2021, 13:16:23 UTC | MAINTAINERS: Add an entry for NVMe This was missed when NVMe support was initially brought to U-Boot back in 2017. Add an entry for it and list myself as the maintainer. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> | 23 June 2021, 09:21:14 UTC |
| bf2a283 | Bin Meng | 22 June 2021, 13:16:22 UTC | doc: develop: Convert README.nvme to reST This converts the existing README.nvme to reST, and puts it under the develop/driver-model/ directory. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| 78d5f20 | Bin Meng | 22 June 2021, 13:16:21 UTC | nvme: Don't clear nvme blk device's priv space A udevice's priv space is cleared in alloc_priv() in the DM core. Don't do it again in its probe() routine. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| 757cc4b | Bin Meng | 22 June 2021, 13:16:20 UTC | nvme: Drop useless members of 'struct nvme_ns' mode_select_num_blocks and mode_select_block_len in 'struct nvme_ns' are not useful. Drop them. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| 8c60d40 | Bin Meng | 22 June 2021, 13:16:19 UTC | nvme: Eliminate the offset of one during block dev creation At present there is an offset of one added during the creation of block device. This can be very confusing as we wanted to encode the namespace id in the block device name but namespae id cannot be zero. This changes to use the namespace id directly in the block device name, eliminating the offset of one effectively. Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| 478f7fc | Bin Meng | 22 June 2021, 13:16:18 UTC | nvme: Skip block device creation for inactive namespaces At present for each namespace there is a block device created for it. There is no issue if the number of supported namespaces reported from the NVMe device is only 1. Since QEMU commit 7f0f1acedf15 ("hw/block/nvme: support multiple namespaces"), the number of supported namespaces reported has been changed from 1 to 256, but not all of them are active namespaces. The actual active one depends on the QEMU command line parameters. A common case is that namespace 1 being active and all other 255 being inactive. If a namespace is inactive, the namespace identify command returns a zero filled data structure. We can use field NSZE (namespace size) to decide whether a block device should be created for it. Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| 8434425 | Bin Meng | 22 June 2021, 13:16:17 UTC | nvme: Move block dev creation from uclass post_probe() to driver probe() At present the block device creation happens in the NVMe uclass driver post_probe() phase. In preparation to support multiple namespaces, we should issue namespace identify before creating block devices but that touches the underlying hardware hence it is not appropriate to do such in the uclass driver post_probe(). Let's move it to driver probe() phase instead. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| c3e52c7 | Wesley Sheng | 22 June 2021, 03:34:43 UTC | nvme: Remove the redundant aqa value setting AQA (Admin Queue Attributes) register is a dword size with lower word of ASQS, and higher word of ACQS. The code set the variable aqa twice, but it is redundant. Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| 859b33c | Wesley Sheng | 22 June 2021, 03:34:21 UTC | nvme: Correct the prps per page calculation method Each prp is 8 bytes, calculate the number of prps per page should just divide page size by 8 there is no need to minus 1 Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| b12f623 | David Lamparter | 06 May 2021, 18:24:30 UTC | nvme: fix for big endian systems writel() and co. already include the endian swap; doing the swap twice is, er, unhelpful. Tested on a P4080DS, which boots perfectly fine off NVMe with this. Signed-off-by: David Lamparter <equinox@diac24.net> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> | 23 June 2021, 09:21:14 UTC |
| 6fbe06a | Bin Meng | 18 June 2021, 07:09:30 UTC | x86: Discard .note.gnu.property sections When switching to kernel.org x86_64 gcc 11.1.0 toolchain, u-boot.rom built from qemu-x86_defconfig no longer boots anymore. Investigation shows that U-Boot fails at a very early stage during the boot process, in fdtdec_prepare_fdt() where fdt_check_header() complains that there is not a valid device tree found at gd->fdt_blob which points to _end. Now _end points to an allocated section .note.gnu.property which of course is wrong. This issue is however not seen when using the default Ubuntu 20.04 gnu toolchain (gcc 9.3.0 with binutils 2.34). Further investigation shows that it is caused by a behavior change of binutils v2.36 which is part of the kernel.org gcc 11.1.0 toolchain, via the following commit: 939b95c77bf2 ("Linux/x86: Configure gas with --enable-x86-used-note by default") In fact, there was already a regression bug report [1] for binutils two months ago, but the binutils folks did not think it is a bug :( To resolve this, there are several options: * pass -Wa,-mx86-used-note=no to gas * pass -R .note.gnu.property to objcopy * discard the section in the linker script Linux kernel uses the discard way [2], so let's do the same for U-Boot. [1] https://sourceware.org/bugzilla/show_bug.cgi?id=27753 [2] commit 4caffe6a28d3 ("x86/vdso: Discard .note.gnu.property sections in vDSO") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> | 23 June 2021, 09:21:14 UTC |
| 2600dd8 | Jan Kiszka | 20 June 2021, 20:29:13 UTC | Makefile: Adjust indention of GENENV quiet output The column width for a command name is 8. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> | 22 June 2021, 18:01:22 UTC |
| 5a87df8 | Da Xue | 22 June 2021, 02:39:19 UTC | autoboot: fix typos of CONFIG_AUTOBOOT_USE_MENUKEY Replace typo CONFIG_USE_AUTOBOOT_MENUKEY with CONFIG_AUTOBOOT_USE_MENUKEY as when they were introduced initially there was some mismatch in which name was used where. Fixes: 8fc31e23aa83 ("autoboot: Rename CONFIG_MENUKEY to CONFIG_AUTOBOOT_MENUKEY") Signed-off-by: Da Xue <da@libre.computer> | 22 June 2021, 18:01:22 UTC |
| c7d1b18 | Christian Melki | 07 June 2021, 09:21:15 UTC | disk/part_dos.c: Fix a variable typo in write_mbr_partitions() This function is passed *dev not *dev_desc, so pass the right name to part_init(). Fixes: f14c5ee5ab8b ("disk: part_dos: update partition table entries after write") Signed-off-by: Christian Melki <christian.melki@t2data.com> | 22 June 2021, 17:58:08 UTC |
| 1ce892c | Bin Meng | 21 June 2021, 23:33:21 UTC | azure: Use msys2 20210604 installer for Windows build MSYS2 Windows build started to fail since yesterday (Jun 21): checking keyring... checking package integrity... error: gcc-libs: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust :: File /var/cache/pacman/pkg/gcc-libs-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)). error: gcc: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust :: File /var/cache/pacman/pkg/gcc-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)). error: failed to commit transaction (invalid or corrupted package) Errors occurred, no packages were upgraded. Switching to the latest installer (version 20210604) seems to fix it. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Tom Rini <trini@konsulko.com> | 22 June 2021, 13:06:03 UTC |
| f132aab | Fabio Estevam | 07 June 2021, 20:40:09 UTC | Revert "mmc: fsl_esdhc_imx: use VENDORSPEC_FRC_SDCLK_ON to control card clock output" This reverts commit 63756575b42b8b4fb3f59cbbf0cedf03331bc2d2. Since this commit a imx6qdl-pico board boots extremely slowly in both SPL as well as U-Boot proper. Fix this regression by reverting the offending commit for now. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com> | 22 June 2021, 04:03:32 UTC |
| d77d61e | Jaehoon Chung | 30 May 2021, 23:31:50 UTC | mmc: mmc-uclass: change to static about dm function Change to static about dm function. They can be used with wrapper functions. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> | 22 June 2021, 04:03:20 UTC |
| 2da2335 | Jaehoon Chung | 30 May 2021, 23:31:49 UTC | mmc: fsl_esdhc_imx: use mmc_send_cmd instead of dm_mmc_send_cmd Use mmc_send_cmd instead of dm_mmc_send_cmd. It doesn't need to distinguish this function. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> | 22 June 2021, 04:03:11 UTC |
| 5c2beda | Reuben Dowle | 13 May 2021, 22:15:43 UTC | mmc: Update environment variable with active partition This patch allows uboot scripts make choices about where to boot from based on the active mmc boot partition. This allows having two copies of kernel, filesystems etc, and choosing which to boot from based off of the active bootloader partition. Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> | 22 June 2021, 04:02:46 UTC |
| 1925e65 | Ley Foon Tan | 26 April 2021, 05:17:46 UTC | mmc: dwmmc: socfpga: Get "fifo-mode" property from DT Add FIFO mode support for SoCFPGA dwmmc, read "fifo-mode" property from DT. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> | 22 June 2021, 04:02:32 UTC |
| 8cb9d3e | Ley Foon Tan | 26 April 2021, 03:35:05 UTC | mmc: dw_mmc: Fixes data read when receiving DTO interrupt in FIFO mode The data read is not working when using FIFO mode. From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is received, the software should read the remaining data from FIFO. Add DTO interrupt checking on data read path and clear interrupts before start reading from FIFO. So, it doesn't clear the next pending interrupts unintentionally after read from FIFO. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> | 22 June 2021, 04:02:11 UTC |
| 3a3672c | Weijie Gao | 20 April 2021, 08:37:10 UTC | mmc: mtk-sd: increase the minimum bus frequency With a 48MHz input clock, the lowest bus frequency can be as low as 48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause the mmc framework take seconds to finish the initialization. Limiting the minimum bus frequency to a slightly higher value can solve the issue without any side effects. Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> | 22 June 2021, 04:01:52 UTC |
| 52ce6a6 | Andrey Zhizhikin | 01 May 2021, 20:23:04 UTC | imx8mm: configs: enable distro default features imx8mm ekv has been switched to use distro boot commands, but had no correct options enabled to support sysboot. According to the README.distro, sysboot is consindered to be a recommended way of using distro boot commands, it required default distro features to be enabled instead of only those that are relevant to the boot script. Replace the boot script specific options in the config to a default distro option. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Peng Fan <peng.fan@nxp.com> Fixes: 2df8930bf9 ("imx8mm: configs: add support for distro boot commands") Reviewed-by: Fabio Estevam <festevam@gmail.com> | 21 June 2021, 11:35:23 UTC |
| 06f4e42 | Andrey Zhizhikin | 01 May 2021, 20:23:05 UTC | imx8mp: configs: enable distro default features imx8mp ekv has been switched to use distro boot commands, but had no correct options enabled to support sysboot. According to the README.distro, sysboot is consindered to be a recommended way of using distro boot commands, it required default distro features to be enabled instead of only those that are relevant to the boot script. Replace the boot script specific options in the config to a default distro option. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Peng Fan <peng.fan@nxp.com> Fixes: 9b162b1d1f ("imx8mp: configs: add support for distro boot commands") Reviewed-by: Fabio Estevam <festevam@gmail.com> | 21 June 2021, 11:33:55 UTC |
| 31b3829 | Fabio Estevam | 17 June 2021, 15:57:29 UTC | o4-imx-nano: Fix dtc warnings Remove the LED unit addresses and reg properties to fix the following dtc build warnings: arch/arm/dts/o4-imx-nano.dtb: Warning (reg_format): /leds/led@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ... arch/arm/dts/o4-imx-nano.dtb: Warning (avoid_default_addr_size): /leds/led@0: Relying on default #address-cells value Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Oleh Kravchenko <oleg@kaa.org.ua> | 21 June 2021, 11:31:40 UTC |
| 97c8cb5 | Tom Rini | 18 June 2021, 15:18:56 UTC | Merge branch 'network_master' of https://source.denx.de/u-boot/custodians/u-boot-net | 18 June 2021, 15:18:56 UTC |
| 54c321f | Tim Harvey | 17 June 2021, 23:08:54 UTC | net: octeontx: smi: use dt live tree API clean up octeontx_smi_probe by using the live-tree API. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> | 18 June 2021, 08:29:17 UTC |
| 75efe7d | Dimitri John Ledkov | 21 April 2021, 11:42:01 UTC | cmd: pxe_utils: sysboot: fix crash if either board or soc are not set. If the environment does not have "soc" or "board" set, and fdtdir option is specified in extlinux.conf, the bootloader will crash whilst dereferencing a null pointer. Add a guard against null soc or board. Fixes a crash of qemu-riscv64_smode configuration, which does not have CONFIG_SYS_SOC defined. Signed-off-by: Dimitri John Ledkov <xnox@ubuntu.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> | 18 June 2021, 08:29:17 UTC |
| 82a3c9e | Michael Walle | 25 February 2021, 15:51:11 UTC | net: use the same alias stem for ethernet as linux Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from the linux tree: $ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l 0 $ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l 633 In u-boot device trees both prefixes are used. Until recently the only user of the ethernet alias was the sandbox test device tree. This changed with commit fc054d563bfb ("net: Introduce DSA class for Ethernet switches"). There, the MAC addresses are inherited based on the devices sequence IDs which is in turn given by the device tree. Before there are more users in u-boot and both worlds will differ even more, rename the alias prefix to "ethernet" to match the linux ones. Also adapt the test cases and rename any old aliases in the u-boot device trees. Cc: David Wu <david.wu@rock-chips.com> Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> | 18 June 2021, 08:29:17 UTC |
| 6e424b4 | Michael Walle | 24 February 2021, 16:30:44 UTC | net: use a more deterministic approach to get the active ethernet device If the environment variable "ethact" is not set, the first device in the uclass is returned. This depends on the probing order of the ethernet devices. Moreover it is not not configurable at all. Try to return the ethernet device with sequence id 0 first which then can be configured by the aliases in a device tree. Fall back to the old mechanism in case of an error. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> | 18 June 2021, 08:29:17 UTC |
| 02036d9 | Heinrich Schuchardt | 03 June 2021, 07:52:41 UTC | net: sun8i-emac: fix MDIO frequency Commit 4f0278dac56a ("net: sun8i-emac: Lower MDIO frequency") leads to network failure on the OrangePi PC. => dhcp sun8i_emac_eth_start: Timeout According to the commit message the change of the MDIO frequency is only required for external PHYs. Fixes: 4f0278dac56a ("net: sun8i-emac: Lower MDIO frequency") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 18 June 2021, 08:29:17 UTC |
| eab447b | Jassi Brar | 04 June 2021, 09:44:38 UTC | net: synquacer: Add netsec driver Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on CONFIG_SYNQUACER_SPI=y. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> | 18 June 2021, 08:29:17 UTC |
| f024e0b | Daniil Stas | 30 May 2021, 13:34:09 UTC | net: dwc_eth_qos: Revert some changes of commit 3a97da12ee7b Revert some changes of commit 3a97da12ee7b ("net: dwc_eth_qos: add dwc eqos for imx support") that were probably added by mistake. One of these changes can lead to received data corruption (enabling FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings for some platforms. And another makes some writes at unknown memory location. Fixes: 3a97da12ee7b ("net: dwc_eth_qos: add dwc eqos for imx support") Signed-off-by: Daniil Stas <daniil.stas@posteo.net> Cc: Ye Li <ye.li@nxp.com> Cc: Fugang Duan <fugang.duan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> | 18 June 2021, 08:29:17 UTC |
| 07292f8 | Daniil Stas | 23 May 2021, 22:24:48 UTC | net: dwc_eth_qos: Fix needless phy auto-negotiation restarts Disabling clk_ck clock leads to link up status loss in phy, which leads to auto-negotiation restart before each network command execution. This issue is especially big for PXE boot protocol because of auto-negotiation restarts before each configuration filename trial. To avoid this issue don't disable clk_ck clock after it was enabled. Signed-off-by: Daniil Stas <daniil.stas@posteo.net> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> | 18 June 2021, 08:29:17 UTC |
| 7001863 | Tim Harvey | 16 April 2021, 20:25:09 UTC | net: e1000: do not attempt to set hwaddr for i210 without FLASH commit f1bcad22dd19 ("net: e1000: add support for writing to EEPROM") adds support for storing hwaddr in EEPROM however i210 devices do not support this and thus results in errors such as: Warning: e1000#0 failed to set MAC address' Check if a flash device is present and if not return -ENOSYS indicating this is not supported. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> | 18 June 2021, 08:29:17 UTC |
| 3e18487 | Hou Zhiqiang | 12 June 2021, 18:15:41 UTC | Fix a memory leak issue in the RX port initialization. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> | 18 June 2021, 08:29:17 UTC |
| a298d4f | Tom Rini | 17 June 2021, 12:44:56 UTC | Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq - fsl-qoriq: Bug fixes related pfe, eth, thermal node, vid.c, cpu release, mmc, usb, env, etc for Layerscape boards - powerpc: Update Maintainers for some boards. | 17 June 2021, 12:44:56 UTC |
| 7e585b5 | Tom Rini | 17 June 2021, 12:44:23 UTC | Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-riscv - ae350 related dts fixes. | 17 June 2021, 12:44:23 UTC |
| b7efcaf | Priyanka Jain | 17 June 2021, 07:22:46 UTC | board: freescale: t1028xrdb: Add MAINTAINER for revD Add Priyanka Jain as MAINTAINER for T2080RDB_revD_defconfig, T2080RDB_revD_NAND_defconfig, T2080RDB_revD_SDCARD_defconfig and T2080RDB_revD_SPIFLASH_defconfig Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 07:22:54 UTC |
| 390c73b | Ran Wang | 16 June 2021, 12:23:19 UTC | armv8: Update erratum number to align with doc Change the USB erratum number A-050106 to A-050204 as A-050106 is a duplicate and never be published. Fixes 0cfa00cdb94 (“armv8: Add workaround for USB erratum A-050106”) Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 13ea307 | Camelia Groza | 11 June 2021, 12:28:08 UTC | board: freescale: t208xrdb: add a config option for rev D dts fixups Under DM, we rely on u-boot's device tree to provide the correct PHY addresses. The board_fix_fdt callback is intended to be used for device tree fixups before relocation. Unfortunately, this isn't an option when booting from flash since the device tree isn't writable before relocation. This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a board revision D or up is the target. The config option is used to set the correct Aquantia PHY address in the board's u-boot device tree. Defconfig files with the option enable explicitly are added for convenience. Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 4e21a55 | Camelia Groza | 16 June 2021, 12:17:31 UTC | board: freescale: t208xrdb: add Linux fdt fix-ups for rev D The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs connected to MAC1 and MAC2. The second Aquantia PHY is located at a different address on the MDIO bus compared to rev C (0x8 instead of 0x1). Fix-up the Linux device tree to update the PHY address for the second Aquantia PHY on boards revisions D and up. Also rename the PHY node to reflect the changes. Signed-off-by: Camelia Groza <camelia.groza@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| c91b130 | Camelia Groza | 11 June 2021, 12:28:06 UTC | board: freescale: t208xrdb: detect the board revision version Detect and print the board revision version based on the CPLD registers. Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| a484f7c | Camelia Groza | 11 June 2021, 12:28:05 UTC | board: freescale: t208xrdb: remove the legacy non-DM_ETH code Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the board_eth_init() callback and the non-DM_ETH code paths since they are not needed anymore. Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 11eeeef | Aleksandar Gerasimovski | 08 June 2021, 14:25:21 UTC | pg-wcom-ls102xa: fix sys counter frequency A system clock of 66MHz was chosen for the pg-wcom-ls102xa. Compared to the Evalboard, this corresponds to a reduction of 1/3. The system counter clock should have been reduced accordingly, but that was not the case, so we had a system time that was 1/3 behind the real time. This patch corrects the system counter clock to 8.333MHz = 66.667MHz / 8. Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com> Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 02802eb | Aleksandar Gerasimovski | 08 June 2021, 14:24:32 UTC | pg-wcom-ls102x: initialize front led and app buf This patch adds the front led initialization and the application buffer enable to the eraly board inititlaization. Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com> Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| ccbd2ce | Aleksandar Gerasimovski | 08 June 2021, 14:23:34 UTC | km: ls102x: update device disable configuration acc hw design desc In order to improve power consumption ls102x allows to disable peripherals that are not in use. This patch follows SELI8 HW design description and disables peripherals that are not in use in our designs, the same configuration is applicable and for EXPU1. This patch uses available hwconfig option for updating ls102x device disable configuration. Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| fd49502 | Aleksandar Gerasimovski | 08 June 2021, 14:21:15 UTC | km: ls102x: set ethrotate envvar to no The default behavior in the latest u-boot revisions is to rotate the active net device to the next available if the requested link is not established. For our ls102x based devices this would mean that if active debug net device is not available, u-boot will rotate and set the next net device that is one of the estar adapters. To return from this situation manual action to set correct ethact adapter will be needed and this can be annoying when working in debug mode. Setting ethrotate=no will disable net adapter rotation and will make sure that the primary adapter is always used. Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| fbb0e15 | Aleksandar Gerasimovski | 08 June 2021, 14:20:13 UTC | km/scripts: fix saveenv command syntax This is most probably a typo, and in older u-uboot versions is same as 'saveenv', in the newer uboot versions there is a separate 'save' command that is different from 'saveenv'. Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| a098064 | Aleksandar Gerasimovski | 08 June 2021, 14:19:08 UTC | km: ls102xa: add missing define for PRAM regions In our designs we reserve PRAM area at the end of the RAM, and in order this area to be visible and taken into account by the u-boot memory mgmt CONFIG_PRAM has to be defined. Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 3aea3dd | Aleksandar Gerasimovski | 08 June 2021, 14:17:34 UTC | km/ls102xa: add support for u-boot POST memory test From production view this is standard test executed during production on all linux based foxmc cards. On CENT2 HW defined memory region is zero means that some DDR accesses are done by memory_post_dataline and memory_post_addrline but pattern tests are skipped that's why mem_regions is fast there. On ls102x for the complete DDR region of 1GiB memory_regions_post_test takes approx. 4min and this is too much for production, so this patch defines only 1MiB region as compromise. Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| a7fd6fa | Aleksandar Gerasimovski | 08 June 2021, 14:16:28 UTC | board/km: add support for expu1 design based on nxp The EXPU1 design is a new 40G capable ethernet service unit card for Hitachi-Powergrids wired-com product lines. The base SoC is same as for already added SELI8 card, consequently the already added u-boot support for SELI8 is reused. Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com> Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> [Fixed new line error at EOF] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 0b036d4 | Priyanka Jain | 08 June 2021, 08:07:01 UTC | board: freescale: t102xrdb: Add MAINTAINER Add "Priyanka Jain <priyanka.jain@nxp.com>" as MAINTAINER for t102xrdb board. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| eccf98f | Priyanka Jain | 08 June 2021, 08:07:00 UTC | board: freescale: p2041rdb: Add MAINTAINER Add "Priyanka Jain <priyanka.jain@nxp.com>" as MAINTAINER for p2041rdb board. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 6d1657b | Priyanka Jain | 08 June 2021, 08:06:59 UTC | board: freescale: p1_p2_rdb_pc: Add MAINTAINER Add "Priyanka Jain <priyanka.jain@nxp.com>" as MAINTAINER for p1_p2_rdb_pc board. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 0eb946e | Priyanka Jain | 08 June 2021, 08:06:58 UTC | board: freescale: t4rdb: Add MAINTAINER Add "Priyanka Jain <priyanka.jain@nxp.com>" as MAINTAINER for t4rdb board. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| fb6c96f | Lasse Klok Mikkelsen | 08 June 2021, 06:39:12 UTC | arm: dts: ls1021a.dtsi: Fix invalid reg on gpio nodes Address and size cells on SOC are set to 1. But gpio nodes are specified with 2 cells. This fixes the gpio nodes to correct cells. Signed-off-by: Lasse Klok Mikkelsen <lkmi@prevas.dk> Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 50dae8e | Aleksandar Gerasimovski | 04 June 2021, 13:40:58 UTC | net: tsec: add option to set device max-speed via dts Current tsec adapter sets adapter gigabit capabilities by default, and in reality this must not always be the case. It is possible that tsec adapter is used for 100Mbps connection, and in this case setting 1000Mbps capabilities can lead to some side effects such longer autoneg process. In our ls102x designs this problem leads to long autoneg times (> 4 sec) in case board rgmii link is 100Mbps capable only. Limiting the rgmii link capabilities provides faster and smoother link establishment. Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 0753603 | Aleksandar Gerasimovski | 04 June 2021, 09:25:00 UTC | keymile: common: fix hexadecimal env variable format Commit df86d32 breaks linux kernel and product application boot. Linux kernel and our product application scripts are expecting 0x prefix for hexadecimal values, while env_set_hex writes them without a prefix. This patch partially revert env_set_hex usage for affected env variables. Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
