| 058c08d | Aleksandar Gerasimovski | 04 June 2021, 09:17:56 UTC | configs: seli8: set envsize to 0x4000 During the mainlining of the board this was by mistake set to sector size. Our user space env scripts are expecting envsize of 0x4000, and setting this differently will break our cross-platform compatibility. Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 34f39ce | Yangbo Lu | 03 June 2021, 02:51:19 UTC | armv8: layerscape: drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT is used instead. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28] Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| b1d5986 | Yangbo Lu | 03 June 2021, 02:51:18 UTC | mmc: fsl_esdhc_imx: drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 There is no i.MX board using such option. Drop it. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| ae7020b | Yangbo Lu | 03 June 2021, 02:51:17 UTC | mmc: fsl_esdhc: convert to CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT For eSDHC, power supply is through peripheral circuit. Some eSDHC versions have value 0 of the bit but that does not reflect the truth. 3.3V is common for SD/MMC, and is supported for all boards with eSDHC in current u-boot. So, make 3.3V is supported in default in code. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if future board does not support 3.3V. This is also a fix-up for one previous patch, which converted to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 that is not a Kconfig option. Fixes: 52faec31827e ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 6bc2419 | Matt Merhar | 30 May 2021, 00:16:17 UTC | board: freescale: p2041rdb: use correct EEPROM address length These boards, according to the schematic and per the board I own, use an M24256-BWDW6TP I2C EEPROM which requires two address bytes. This fixes the 'mac' command which is used to program, among other things, the MAC addresses for the ethernet interfaces on the board. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 8bb2085 | Biwen Li | 21 May 2021, 07:15:06 UTC | configs: ls2088aqds: fix synchronous exception IFC NOR flash base address of ls2088a is 0x580000000, and offset of env crc is 0x500000, so fix the macro CONFIG_ENV_ADDR to fix synchronous exception(access illegal address) Fixes: 59071804c1 ("configs: ls2080a: Correct ENV_ADDR value") Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| effcb1e | Kuldeep Singh | 19 May 2021, 11:10:12 UTC | configs: ls1088a: Enable CONFIG_SYS_RELOC_ENV_ADDR Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 38d1a18 | Yangbo Lu | 14 May 2021, 02:33:57 UTC | arm: dts: lx2162aqds: support eMMC HS400 mode on esdhc1 Add properties related to eMMC HS400 mode for esdhc1. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 8e221b4 | Hou Zhiqiang | 13 May 2021, 06:54:32 UTC | pci: layerscape-ep: Add check of the PCIe controller enablement Stop to initialize the PCIe controller if it's disabled by RCW. Fixes: 118e58e26eba ("pci: layerscape: Split the EP and RC driver") Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| ff64e9a | Chaitanya Sakinam | 07 May 2021, 04:22:05 UTC | armv8: ls1012a: Pass PPFE firmware to Linux through FDT Read Linux PPFE firmware from flash partition and pass it to Linux through FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs. (FDT may increase at max by 64KB) Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com> Signed-off-by: Anji J <anji.jagarlmudi@nxp.com> Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| addec35 | Yangbo Lu | 27 April 2021, 08:42:11 UTC | armv8: layerscape: enable eMMC HS400 workarounds for LX2160A/LX2162A Enable eMMC HS400 workarounds for LX2160A/LX2162A. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 84c2e04 | Jiafei Pan | 21 April 2021, 04:12:49 UTC | armv8: layerscape: add PSCI support for cpu release For cpu release command, check whether PSCI is supported firstly, if supported, use PSCI to kick off secondary cores, otherwise still use spin table. Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com> [Fixed checkpatch alignment CHECKs] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| c0eeb73 | Priyanka Singh | 19 April 2021, 05:45:04 UTC | board: freescale: vid.c: Add check for return value of adjust_vdd() Add check for return value of adjust_vdd() Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 17 June 2021, 06:16:11 UTC |
| 62ce0a0 | Bin Meng | 15 June 2021, 05:45:57 UTC | riscv: andes_plic: Fix riscv_get_ipi() mask Current logic in riscv_get_ipi() for Andes PLICSW does not look correct. The mask to test IPI pending bits for a hart should be left shifted by (8 * gd->arch.boot_hart), just the same as what is done in riscv_send_ipi(). Fixes: 8b3e97badf97 ("riscv: add functions for reading the IPI status") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Tested-by: Rick Chen <rick@andestech.com> | 17 June 2021, 01:39:46 UTC |
| 279de75 | Bin Meng | 04 June 2021, 23:00:30 UTC | riscv: ae350: doc: Remove CONFIG_SKIP_LOWLEVEL_INIT The doc says CONFIG_SKIP_LOWLEVEL_INIT is in ax25-ae350.h, while actually it is not. Remove it. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> | 17 June 2021, 01:39:18 UTC |
| 77eae0e | Bin Meng | 04 June 2021, 05:51:13 UTC | riscv: ae350: dts: Add missing "u-boot, dm-spl" for SPL config At present the AE350 SPL defconfig is using OF_PRIOR_STAGE. The intention was to use gdb to load device tree before running U-Boot SPL/proper from RAM. When we switch to OF_SEPARATE we will have to use our own DT but without "u-boot,dm-spl" in several essential nodes, SPL does not boot. Let's add all the required "u-boot,dm-spl" for SPL config. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> | 17 June 2021, 01:39:08 UTC |
| 048aff6 | Bin Meng | 04 June 2021, 05:51:12 UTC | riscv: ae350: dts: Fix #interrupt-cells for plic0 in 32-bit All the device nodes that refer to plic0 as their interrupt parent have 2 cells encoded in their interrupts property, but plic0 only provides 1 cell in #interrupt-cells which is incorrect. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com> | 17 June 2021, 01:39:08 UTC |
| f050dd2 | Bin Meng | 04 June 2021, 05:51:11 UTC | riscv: ae350: dts: Remove the unnecessary #address-cells in plic nodes PLIC nodes don't have child nodes, so #address-cells is not needed. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com> | 17 June 2021, 01:39:08 UTC |
| 5c267e0 | Bin Meng | 04 June 2021, 05:51:10 UTC | riscv: ae350: dts: Remove the unnecessary space in bootargs There are two spaces before "debug' in bootargs. Drop one. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com> | 17 June 2021, 01:39:08 UTC |
| 2ff6b79 | Bin Meng | 04 June 2021, 05:51:09 UTC | riscv: ae350: dts: Add SPDX license header The SPDX license header is currently missing. Add one. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com> Reviewed-by: Rick Chen <rick@andestech.com> | 17 June 2021, 01:39:08 UTC |
| b2c4b7f | Tom Rini | 16 June 2021, 15:18:11 UTC | Merge tag 'u-boot-imx-20210616' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20210616 ------------------- - imxrt : fixes, USB, imxrt1020-evk - imx8m: fix for verdin-imx8mm Add conga-QMX8 board - imx6 : documentation for pico-imx6: Add SeeedStudio NPI-IMX6ULL Support ventana: DM PCI - imx7d: added SMEGW01 board CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765 | 16 June 2021, 15:18:11 UTC |
| 864c3db | Mian Yousaf Kaukab | 14 April 2021, 10:33:58 UTC | ls1012a: net: pfe: remove pfe stop from bootcmd When using bootefi to boot a EFI binary, u-boot is supposed to provide networking service for EFI application. Currently, 'pfe stop' command is called from bootcmd before running bootefi. As a result network stops working for EFI applications and console is flooded with "Rx pkt not on expected port" messages. Implement board_quiesce_devices() for ls1012a boards and call pfe_command_stop() from it instead of calling 'pfe stop' from *_bootcmd and bootcmd. Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com> Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> [Fixed checkpatch space error] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> | 16 June 2021, 12:44:08 UTC |
| 2bf4658 | Michael Walle | 13 April 2021, 15:54:17 UTC | board: sl28: fix RGMII clock and voltage It was noticed that the clock isn't continuously enabled when there is no link. This is because the 125MHz clock is derived from the internal PLL which seems to go into some kind of power-down mode every once in a while. The LS1028A expects a contiuous clock. Thus enable the PLL all the time. Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO regulator. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 16 June 2021, 12:44:08 UTC |
| fb4e64e | Manish Tomar | 13 April 2021, 07:08:34 UTC | configs: ls1046afrwy: Add secure boot config Add required CONFIG_NXP_ESBC for ls1046afrwy to enable ESBC Chain of Trust. Signed-off-by: Manish Tomar <manish.tomar@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> | 16 June 2021, 12:44:08 UTC |
| 9301a5c | Tom Rini | 15 June 2021, 12:23:04 UTC | Merge https://source.denx.de/u-boot/custodians/u-boot-marvell - Turris: Fix bootcmd_rescue (Pali) | 15 June 2021, 12:23:04 UTC |
| 029bb91 | Pali Rohár | 14 June 2021, 14:45:58 UTC | arm: mvebu: turris_{omnia, mox}: ensure running bootcmd_rescue always works One of the points of putting the rescue boot command into default environment is that user can invoke it without physical access to the board (without having to press the factory reset button), by running run bootcmd_rescue in U-Boot's console. Therefore we have to ensure that bootcmd_rescue is always set to default value, regardless of whether the factory reset button was pressed. Otherwise the variable will be empty for example after upgrade from previous U-Boot. Fixes: ec3784d62646 ("arm: mvebu: turris_mox: add support for board rescue mode") Fixes: 176c3e7760a2 ("arm: mvebu: turris_omnia: support invoking rescue boot from console") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> | 15 June 2021, 05:21:54 UTC |
| c4737cd | Tom Rini | 11 June 2021, 12:29:34 UTC | Merge tag 'xilinx-for-v2021.07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-microblaze Xilinx changes for v2021.07-rc5 zynqmp: - Fix ANALOG_BUS value after powerup - Disable EFI_CAPSULE_ON_DISK_EARLY zynqmp-gqspi: - Fix write issue | 11 June 2021, 12:29:34 UTC |
| 6bb577d | Michal Simek | 10 June 2021, 12:33:55 UTC | arm64: zynqmp: Disable EFI_CAPSULE_ON_DISK_EARLY Sata/scsi and usb based devices are not started at this stage that's why disks are not found and early update can't happen. It is because of deficiency in the UEFI implementation which is not able to deal with block devices which are added or removed after initialization. EFI capsule on disk early feature needs to be fixed first to be able to enable this feature properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> | 11 June 2021, 07:24:58 UTC |
| 2ffa653 | Ashok Reddy Soma | 25 May 2021, 12:36:27 UTC | spi: zynqmp_gqspi: Fix write issue Enable manual start in zynqmp_qspi_fill_gen_fifo(). Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of GQSPI_IXR_GFEMTY_MASK. Add dummy write to genfifo register in chipselect. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> | 11 June 2021, 07:24:58 UTC |
| 3414712 | Adrian Fiergolski | 08 June 2021, 10:37:23 UTC | arm64: zynqmp: Writing correct value to ANALOG_BUS The default register configuration after powerup for PSSYSMON_ANALOG_BUS register is incorrect. Hence, fix this in SPL by writing correct fixed value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c") in Xilinx:embeddedsw[1]. [1] https://github.com/Xilinx/embeddedsw Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> | 11 June 2021, 07:24:58 UTC |
| cf066a2 | Tom Rini | 10 June 2021, 17:27:14 UTC | Merge https://source.denx.de/u-boot/custodians/u-boot-marvell - mvebu: Turris MOX misc updates (cmds, rescue mode, LED's etc) (Marek) - mvebu: correct Armada 8K addresses (Heinrich) | 10 June 2021, 17:27:14 UTC |
| c64e2bd | Heinrich Schuchardt | 08 June 2021, 10:00:35 UTC | arm64: mvebu: correct Armada 8K addresses 0x04000000- 0x06000000 is reserved memory. We cannot load to anything here. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Stefan Roese <sr@denx.de> | 10 June 2021, 05:18:06 UTC |
| d51bdae | Marek Behún | 07 June 2021, 14:34:51 UTC | arm: mvebu: turris_mox: enable options for Turris network boot Enable configuration options to support Turris network boot. This includes FIT support and some crypto commands. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> | 10 June 2021, 05:18:06 UTC |
| f221333 | Marek Behún | 07 June 2021, 14:34:50 UTC | arm: mvebu: dts: turris_mox: add nodes for SPI NOR partitions Add nodes for SPI NOR partitions to the device tree of Turris MOX, as are in Linux' device tree. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> | 10 June 2021, 05:18:06 UTC |
| 8805647 | Marek Behún | 07 June 2021, 14:34:49 UTC | arm: mvebu: configs: turris_mox: add fdtfile default env variable Add default fdtfile environment variable with value marvell/armada-3720-turris-mox.dtb. This can be useful for some boot scenarios. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> | 10 June 2021, 05:18:06 UTC |
| 4585341 | Marek Behún | 07 June 2021, 14:34:48 UTC | arm: mvebu: turris_mox: start blinking PHY LEDs when entering rescue Configure blinking on ethernet PHY LEDs on the MOX A board when entering rescue mode via reset button. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> | 10 June 2021, 05:18:06 UTC |
| ec3784d | Marek Behún | 07 June 2021, 14:34:47 UTC | arm: mvebu: turris_mox: add support for board rescue mode Add necessary config options and board code to support board factory reset / rescue mode on Turris MOX. In order to also support invoking rescue mode from U-Boot console, without having to press the factory reset button, put the rescue command into `bootcmd_rescue` default environment variable. When factory reset button is pressed, invoke rescue mode via distroboot by setting `boot_targets` to `rescue`. Rescue boot from console can be invoked by running run bootcmd_rescue Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> | 10 June 2021, 05:18:06 UTC |
| e04bf43 | Marek Behún | 07 June 2021, 14:34:46 UTC | arm: mvebu: dts: turris_mox: add button and LED nodes Add nodes for indicator LED and reset button so that board code can implement board factory reset mechanism. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> | 10 June 2021, 05:18:06 UTC |
| 0008d80 | Joao Marcos Costa | 17 May 2021, 21:20:38 UTC | fs/squashfs: fix reading of fragmented files The fragmented files were not correctly read because of two issues: - The squashfs_file_info struct has a field named 'comp', which tells if the file's fragment is compressed or not. This field was always set to 'true' in sqfs_get_regfile_info and sqfs_get_lregfile_info. It should actually take sqfs_frag_lookup's return value. This patch addresses these two assignments. - In sqfs_read, the fragments (compressed or not) were copied to the output buffer through a for loop which was reading data at the wrong offset. Replace these loops by equivalent calls to memcpy, with the right parameters. I tested this patch by comparing the MD5 checksum of a few fragmented files with the respective md5sum output in sandbox, considering both compressed and uncompressed fragments. Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com> Tested-by: Richard Genoud <richard.genoud@posteo.net> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> | 10 June 2021, 00:58:20 UTC |
| 4670416 | Tom Rini | 09 June 2021, 12:20:36 UTC | Merge https://source.denx.de/u-boot/custodians/u-boot-usb - dwc2 and cdns3 fixes | 09 June 2021, 12:20:36 UTC |
| 5e425a3 | Tom Rini | 09 June 2021, 12:20:24 UTC | Merge tag 'efi-2021-07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi Pull request for efi-2021-07-rc5 Documentation: * pinmux and ums man-page Bug fixes: * Consider that partition numbers as hexadecimal. * Avoid a possible NULL dereference in efi_capsule_delete_file(). | 09 June 2021, 12:20:24 UTC |
| 40496ac | Fabio Estevam | 28 May 2021, 13:26:57 UTC | mx7d: Add Storopack's SMEGW01 board Add support for Storopack's SMEGW01 board, which is an IoT gateway based on the i.MX7D SoC. Based on the original U-Boot work done by Phytec. Signed-off-by: Fabio Estevam <festevam@denx.de> | 09 June 2021, 11:34:38 UTC |
| d4f15ec | Andrey Zhizhikin | 02 May 2021, 14:32:37 UTC | imx8mn: configs: add support for distro boot commands Supported boot device types in iMX8MN: MMC, DHCP. Add DISTRO_DEFAULTS config option and include the distro boot command header file to enable full support of distro boot on i.MX8M Nano EVK (both DDR and LPDDR derivatives). Drop previous environment, which was targeting customized boot commands and boot order. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> | 09 June 2021, 11:34:26 UTC |
| a3a0bc8 | Navin Sankar Velliangiri | 18 May 2021, 03:33:20 UTC | imx: Add SeeedStudio NPI-IMX6ULL Support CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 49C Reset cause: POR Model: Seeed NPi iMX6ULL Dev Board with NAND Board: Seeed NPi i.MX6ULL Dev Board DRAM: 512 MiB NAND: 512 MiB MMC: FSL_SDHC: 0 In: serial@2020000 Out: serial@2020000 Err: serial@2020000 Net: FEC0 Working: - Eth0 - MMC/SD - NAND - UART 1 - USB host Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com> Note: Changes in v2: * removed unnecessary space in imx6ull-seeed-npi-imx6ull-dev-board.dts file. * Used SZ_2M for CONFIG_SYS_MALLOC_LEN size allocation. | 09 June 2021, 11:34:18 UTC |
| fe133eb | Oliver Graute | 31 May 2021, 13:50:40 UTC | imx: support for conga-QMX8 board Add i.MX8QM qmx8 congatec board support U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Congatec QMX8 Qseven series Board: conga-QMX8 Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9 Boot: SD2 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 switch to partitions #0, OK mmc2 is current device Net: Error: ethernet@5b040000 address not set. No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> | 09 June 2021, 11:34:09 UTC |
| 6ac4d44 | Andrey Zhizhikin | 03 May 2021, 07:59:17 UTC | arm: imx: imx8mm: correct unrecognized fracpll frequency Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ() macro, which expands the value provided to the Hz range without taking into account the precise Hz setting. This causes the frequency of 266 MHz not ot be found in the imx8mm_fracpll_tbl, since it is entered there with a precise Hz value. This in turn causes the boot hang in SPL, as proper DDR fracpll frequency cannot be determined. Correct the value in imx8mm_fracpll_tbl to match the one expanded by MHZ(266) macro, rounding it down to MHz range only. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m") Reviewed-by: Fabio Estevam <festevam@gmail.com> | 09 June 2021, 11:34:01 UTC |
| b891630 | Fabio Estevam | 27 May 2021, 21:43:06 UTC | pico-imx6: README: Fix the boot mode settings URL The original URL that explains the boot mode setting is no longer valid. Update to the new one. Signed-off-by: Fabio Estevam <festevam@gmail.com> | 09 June 2021, 11:33:45 UTC |
| cd18f1e | Tim Harvey | 03 May 2021, 18:21:27 UTC | imx: ventana: enable dm support for PCI and FEC ethernet Enable driver model support for FEC ethernet which allows us to remove the iomux and board_eth_init function. Replace the toggling of the ethernet phy reset with dt configuration. Enable driver model support for PCI which allows us to remove the eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for PCI devices on init such as the e1000 that is present on the GW552x. Convert board_pci_fixup to use dm callback and remove pcidisable env variable which is not supported for DM_PCI and thus leave PCI always enabled during init. Signed-off-by: Tim Harvey <tharvey@gateworks.com> | 09 June 2021, 11:33:35 UTC |
| d9a7f1a | Andrey Zhizhikin | 03 May 2021, 08:02:10 UTC | arm: imx: imx8mm: clock: make debug output more descriptive Clock initialization functionality has ambitious debug messages, which are printed out when failures are triggered during execution: - Separate frequency table lookup functions have the the same output that makes it impossible to understand which function failed and produced the output - PLL decoding routine has a generic debug statement printed, which does not state the actual value failed to be found Extend the output for both cases with prefixing table lookup functions output with function name, and report the failed value in PLL decoding routine. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> | 09 June 2021, 11:33:26 UTC |
| 1180bae | Oleh Kravchenko | 14 May 2021, 21:18:33 UTC | Add EV-iMX280-NANO-X-MB board A simple prototyping board with one microSD port, one Ethernet port, 2 USB ports, I2C, SPI, GPIO, and UART interfaces. Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua> Cc: Stefano Babic <sbabic@denx.de> | 09 June 2021, 11:32:49 UTC |
| 3675ac0 | Oleh Kravchenko | 14 May 2021, 21:18:31 UTC | Add out4.ru O4-iMX-NANO board Board designed for quick prototyping and has one microSD port, 2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO, UART interfaces, and 2 RGB LEDs. Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua> Cc: Stefano Babic <sbabic@denx.de> | 09 June 2021, 11:32:42 UTC |
| e2017ef | Marek Vasut | 17 May 2021, 22:40:30 UTC | ARM: imx8m: verdin-imx8mm: Increase bootm size to 64 MiB Uncompressed aarch64 kernel Image are rather large, increase the bootm size limit to 64 MiB to cater for that. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Max Krummenacher <max.krummenacher@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> | 09 June 2021, 11:32:35 UTC |
| cb87278 | Giulio Benetti | 20 May 2021, 14:10:18 UTC | configs: imxrt1050-evk: enable host usb support and its command Now that usb host is supported let's enable it on this board. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:04:06 UTC |
| 42b9672 | Giulio Benetti | 20 May 2021, 14:10:17 UTC | ARM: dts: imxrt1050-evk: enable usbotg1 node as host Enable usbotg1 port node as host usb. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:04:00 UTC |
| 9b91484 | Giulio Benetti | 20 May 2021, 14:10:16 UTC | ARM: dts: imxrt1050: add usbotg1, usbphy1 and usbmisc nodes Usb is now supported so add all required nodes for it in imxrt1050. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:03:54 UTC |
| e7e81e8 | Giulio Benetti | 20 May 2021, 14:10:15 UTC | usb: ehci-mx6: add support for i.MXRT Add support for usb1 and usb2 present on i.IMXRT. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:03:47 UTC |
| 45a5f76 | Giulio Benetti | 20 May 2021, 14:10:14 UTC | clk: imx: clk-imxrt1050: introduce IMXRT1050_CLK_USBOH3 Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to clock driver. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:03:41 UTC |
| 0d90dec | Giulio Benetti | 20 May 2021, 14:10:13 UTC | ARM: IMXRT: introduce is_imxrt*() macros and get_cpu_rev() We need those macros to instruct drivers on how to behave for SoC specific quirks, so let's add it as done for other i.MX SoCs. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:03:33 UTC |
| d7308db | Giulio Benetti | 16 May 2021, 21:57:02 UTC | ARM: dts: imxrt1020: add gpio5 node to this SoC i.MXRT1020 supports gpio5, so let's add a node for it. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:03:26 UTC |
| dc54f82 | Giulio Benetti | 16 May 2021, 21:57:01 UTC | ARM: dts: imxrt1020-evk: move all u-boot, dm-spl to imxrt1020-evk-u-boot.dtsi file At the moment a lot of u-boot,dm-spl properties are present in board .dts file but this is not correct since u-boot,dm-spl property is u-boot specific and must be listed into the separate imrt1020-evk-u-boot.dtsi file. So let's move every u-boot,dm-spl property present in imxrt1020-evk.dts to imxrt1020-evk-u-boot.dtsi file. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:03:19 UTC |
| 1f3555d | Giulio Benetti | 16 May 2021, 21:57:00 UTC | ARM: dts: imxrt1050-evk: move all u-boot, dm-spl to imxrt1050-evk-u-boot.dtsi file At the moment a lot of u-boot,dm-spl properties are present in board .dts file but this is not correct since u-boot,dm-spl property is u-boot specific and must be listed into the separate imrt1050-evk-u-boot.dtsi file. So let's move every u-boot,dm-spl property present in imxrt1050-evk.dts to imxrt1050-evk-u-boot.dtsi file. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:03:08 UTC |
| 31f0e58 | Giulio Benetti | 13 May 2021, 10:19:36 UTC | ARM: dts: imxrt1050-evk: remove u-boot,dm-spl We don't need lcdif to be enable in SPL, so let's remove u-boot,dm-spl. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| a9a5c33 | Giulio Benetti | 13 May 2021, 10:19:35 UTC | ARM: dts: imxrt1050: set lcdif clocks according to mxsfb driver Lcdif needs both "pix" and "axi" clocks to be enabled so let's add them to lcdif node. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| f2d91e6 | Giulio Benetti | 13 May 2021, 10:19:34 UTC | ARM: dts: imxrt1050: move lcdif assigned clock to dtsi Since we assume pll5 is the default lcdif clock source let's move assigned-clocks(-parents) properties to .dtsi file. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| f544dfe | Giulio Benetti | 13 May 2021, 10:19:33 UTC | clk: imx: clk-imxrt1050: introduce LCDIF_PIX and rename LCDIF to LCDIF_APB Lcd peripheral needs 2 different gates to be enable to work, so let's introduce the missing one(LCDIF_PIX) and rename the existing one (LCDIF_APB). Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| 006f0df | Giulio Benetti | 13 May 2021, 10:18:47 UTC | video: mxsfb: add enabling of "disp_axi" clock Some SoC needs "disp_axi" clock to be enabled, so let's try to retrieve it and enabling. If it fails it gives only a debug(), but this clock as well as "axi" clock is not mandatory. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| ee62a05 | Giulio Benetti | 13 May 2021, 10:18:46 UTC | video: mxsfb: add enabling of "axi" clock other than "per" clock On some SoC mxsfb needs more than one clock gate(actual "per" clock). So let's introduce "axi" clock that can be provided but it's not mandatory. This is inspired from linux mxsfb driver. Also let's rename "per" clock to "pix" clock for compatibility with already existing .dts lcdif nodes implementation. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| 72d65bd | Giulio Benetti | 13 May 2021, 10:18:45 UTC | configs: imxrt1050-evk: enable imx gpt timer as tick-timer Let's enable imx-gpt-timer in imx1050-evk defconfig. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| 6f6f03a | Giulio Benetti | 13 May 2021, 10:18:44 UTC | ARM: dts: imxrt1050-evk: add device_type = "memory" to memory node Now device_type = "memory" is mandatory to allow u-boot to read memory node, so let's add it to memory node. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| 0684ec8 | Giulio Benetti | 13 May 2021, 10:18:43 UTC | ARM: dts: imxrt1050-evk-u-boot: make gpt1 present for SPL Timer needs to be already enabled in spl, so let's add its node to spl dtb. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| 7892f3e | Giulio Benetti | 13 May 2021, 10:18:42 UTC | ARM: dts: imxrt1050-evk: set gpt1 as tick-timer for u-boot Let's set gpt1 as u-boot timer. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| 7eacc42 | Giulio Benetti | 13 May 2021, 10:18:41 UTC | ARM: dts: imxrt1050-evk: enable gpt1 timer Enable gpt1 timer. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| 5790db9 | Giulio Benetti | 13 May 2021, 10:18:40 UTC | ARM: dts: imxrt1050: add gpt1 node Add gpt1 node for using it as timer. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| 6cd7a9b | Giulio Benetti | 13 May 2021, 10:18:39 UTC | ARM: dts: imxrt1050: add node label to osc Let's add node label to osc to be used as clock source for other nodes. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| a2d89cc | Giulio Benetti | 13 May 2021, 10:18:38 UTC | configs: imxrt1020-evk: enable imx gpt timer as tick-timer Let's enable imx-gpt-timer in imx1020-evk defconfig. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| d956990 | Giulio Benetti | 13 May 2021, 10:18:37 UTC | ARM: dts: imxrt1020-evk: add device_type = "memory" to memory node Now device_type = "memory" is mandatory to allow u-boot to read memory node, so let's add it to memory node. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| faa4e95 | Giulio Benetti | 13 May 2021, 10:18:36 UTC | ARM: dts: imxrt1020-evk-u-boot: make gpt1 present for SPL Timer needs to be already enabled in spl, so let's add its node to spl dtb. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| e5d10f4 | Giulio Benetti | 13 May 2021, 10:18:35 UTC | ARM: dts: imxrt1020-evk: set gpt1 as tick-timer for u-boot Let's set gpt1 as u-boot timer. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| bc49440 | Giulio Benetti | 13 May 2021, 10:18:34 UTC | ARM: dts: imxrt1020-evk: enable gpt1 timer Enable gpt1 timer. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| df243c9 | Giulio Benetti | 13 May 2021, 10:18:33 UTC | ARM: dts: imxrt1020: add gpt1 node Add gpt1 node for using it as timer. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| bfdbe87 | Giulio Benetti | 13 May 2021, 10:18:32 UTC | ARM: dts: imxrt1020: add node label to osc Let's add node label to osc to be used as clock source for other nodes. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| f8c8573 | Giulio Benetti | 13 May 2021, 10:18:31 UTC | timer: imx-gpt: Add timer support for i.MX SoCs family This timer driver uses GPT Timer (General Purpose Timer) available on a lot of i.MX SoCs family. This driver deals with both 24Mhz oscillator as well as peripheral clock. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> [Giulio: added the driver's stub and handled peripheral clock prescaler setting making driver to work correctly] Signed-off-by: Jesse Taube <mr.bossman075@gmail.com> [Jesse: added init, setting prescaler for 24Mhz support and enabling timer] | 09 June 2021, 11:01:33 UTC |
| 55ad612 | Giulio Benetti | 13 May 2021, 10:18:30 UTC | arm: imxrt: soc: make mpu regions generic This mpu handling works for every i.MXRT SoC that we have, so let's generalize imxrt1050_region_config to imxrt_region_config. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> | 09 June 2021, 11:01:33 UTC |
| b95e5ed | Heinrich Schuchardt | 08 June 2021, 22:21:24 UTC | efi_loader: fix Sphinx warning Brackets '[' need to be escaped to avoid a build warning lib/efi_loader/efi_image_loader.c:223: WARNING: Inline strong start-string without end-string. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Masahisa Kojima <masahisa.kojima@linaro.org> | 09 June 2021, 10:35:01 UTC |
| dcd2bbe | João Loureiro | 17 March 2021, 15:52:21 UTC | usb: dwc2: Avoid delay when initializing USB peripheral by dwc2 When `usb start` is called on the terminal, the dwc2 driver will try to start every USB device as host first, even if it is explicitly configured as peripheral in the device tree (dr_mode = "peripheral"). So to avoid an unwanted 15 seconds delay when initializing the usb (one second per channel = 1s x 15), this patch adds a check to the initialization, and will skip host initialization of the device is explicitly set as peripheral. The checking is already done similarly in the `drivers/usb/gadget/dwc2_udc_otg.c` driver. Signed-off-by: João Loureiro <joaofl@gmail.com> | 09 June 2021, 08:54:26 UTC |
| e27b0ff | Heinrich Schuchardt | 02 June 2021, 17:28:22 UTC | efi_loader: efi_capsule_delete_file() NULL dereference If opening a file fails, the file handle pointer is not valid and must not be dereferenced. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 08 June 2021, 22:16:39 UTC |
| 3dca77b | Heinrich Schuchardt | 25 May 2021, 16:00:13 UTC | efi_loader: partition numbers are hexadecimal If we want to address partition 15 of virtio block device 11, we have to write: virtio b:f When calling sprintf() we must use %x for the device and partition numbers. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 08 June 2021, 22:16:39 UTC |
| 6a1d65e | Patrick Delaunay | 04 June 2021, 16:51:47 UTC | doc: usage: man-page for ums command Provide a man-page for the ums command - USB Mass Storage. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 08 June 2021, 22:13:54 UTC |
| 6b8d9c9 | Patrick Delaunay | 04 June 2021, 16:51:46 UTC | cmd: Add dependency for ums command Add the missing dependency for the command ums: - CONFIG_BLK: call of blk_* functions in usb_mass_storage.c - CONFIG_USB_GADGET: required to select CONFIG_USB_FUNCTION_MASS_STORAGE Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 08 June 2021, 22:13:26 UTC |
| ed9720d | Patrick Delaunay | 02 June 2021, 11:56:45 UTC | doc: usage: man-page for pinmux command Provide a man-page for the pinmux command. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> | 08 June 2021, 22:13:26 UTC |
| 0703f59 | Patrick Delaunay | 02 June 2021, 08:11:19 UTC | doc: usage: reorder commands in index.rst Reorder alphabetically the command in the index of usage in U-Boot documentation. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> | 08 June 2021, 22:13:26 UTC |
| cb26d5a | Tom Rini | 08 June 2021, 21:46:49 UTC | Merge https://source.denx.de/u-boot/custodians/u-boot-sh - More pinctrl updates | 08 June 2021, 21:46:49 UTC |
| c2d21e0 | Kishon Vijay Abraham I | 01 June 2021, 10:56:16 UTC | usb: cdns3: cdns3-ti: Fix clk_get_by_name() to get the correct name Kernel device tree got updated to use clock name as "ref" instead of "usb2_refclk". Fix cdns3-ti.c to use the correct name. Fixes: 70e167495ab2 ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot") Fixes: 6239cc8c4e84 ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> | 08 June 2021, 20:01:20 UTC |
| a2a1485 | Marek Vasut | 26 April 2021, 20:04:11 UTC | pinctrl: renesas: Synchronize R-Car Gen2/Gen3 tables with Linux 5.12 Synchronize R-Car Gen2/Gen3 pinctrl tables with Linux 5.12, commit 9f4ad9e425a1 ("Linux 5.12") . This is a rather large commit, since the macros in sh-pfc.h also got updated, so all the PFC tables must be updated in lockstep. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> | 07 June 2021, 17:35:22 UTC |
| e3b64be | Tom Rini | 07 June 2021, 13:26:39 UTC | Prepare v2021.07-rc4 Signed-off-by: Tom Rini <trini@konsulko.com> | 07 June 2021, 13:26:39 UTC |
| 80da245 | Tom Rini | 07 June 2021, 12:09:35 UTC | configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> | 07 June 2021, 12:09:35 UTC |
| 18dd72a | Tom Rini | 07 June 2021, 11:22:14 UTC | Merge tag 'u-boot-rockchip-20210606' of https://source.denx.de/u-boot/custodians/u-boot-rockchip | 07 June 2021, 11:22:14 UTC |
| 281e95c | Tom Rini | 06 June 2021, 17:00:23 UTC | Merge tag 'dm-pull-6jun21' of https://source.denx.de/u-boot/custodians/u-boot-dm Minor fixes for sandbox and handling of dm-ranges | 06 June 2021, 17:00:23 UTC |
| 0c4e63a | Tom Rini | 05 June 2021, 15:17:55 UTC | Merge tag 'video-for-2021-07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-video - disable legacy video for brxre1, mx28evk, pico-imx6ul, pxm2 and rut boards after DM_VIDEO conversion deadline | 05 June 2021, 15:17:55 UTC |
| 269fa84 | Patrick Delaunay | 21 May 2021, 10:25:00 UTC | test: add dm_test_read_resource Add a test of dev_read_resource with translation or without translation Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Simon Glass <sjg@chromium.org> | 05 June 2021, 13:35:47 UTC |
