Revision 85bd839983778fcd0c1c043327b14a046e979b39 authored by Gu Zheng on 10 June 2015, 18:14:43 UTC, committed by Linus Torvalds on 10 June 2015, 23:43:43 UTC
Izumi found the following oops when hot re-adding a node: BUG: unable to handle kernel paging request at ffffc90008963690 IP: __wake_up_bit+0x20/0x70 Oops: 0000 [#1] SMP CPU: 68 PID: 1237 Comm: rs:main Q:Reg Not tainted 4.1.0-rc5 #80 Hardware name: FUJITSU PRIMEQUEST2800E/SB, BIOS PRIMEQUEST 2000 Series BIOS Version 1.87 04/28/2015 task: ffff880838df8000 ti: ffff880017b94000 task.ti: ffff880017b94000 RIP: 0010:[<ffffffff810dff80>] [<ffffffff810dff80>] __wake_up_bit+0x20/0x70 RSP: 0018:ffff880017b97be8 EFLAGS: 00010246 RAX: ffffc90008963690 RBX: 00000000003c0000 RCX: 000000000000a4c9 RDX: 0000000000000000 RSI: ffffea101bffd500 RDI: ffffc90008963648 RBP: ffff880017b97c08 R08: 0000000002000020 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a0797c73800 R13: ffffea101bffd500 R14: 0000000000000001 R15: 00000000003c0000 FS: 00007fcc7ffff700(0000) GS:ffff880874800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffc90008963690 CR3: 0000000836761000 CR4: 00000000001407e0 Call Trace: unlock_page+0x6d/0x70 generic_write_end+0x53/0xb0 xfs_vm_write_end+0x29/0x80 [xfs] generic_perform_write+0x10a/0x1e0 xfs_file_buffered_aio_write+0x14d/0x3e0 [xfs] xfs_file_write_iter+0x79/0x120 [xfs] __vfs_write+0xd4/0x110 vfs_write+0xac/0x1c0 SyS_write+0x58/0xd0 system_call_fastpath+0x12/0x76 Code: 5d c3 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 48 83 ec 20 65 48 8b 04 25 28 00 00 00 48 89 45 f8 31 c0 48 8d 47 48 <48> 39 47 48 48 c7 45 e8 00 00 00 00 48 c7 45 f0 00 00 00 00 48 RIP [<ffffffff810dff80>] __wake_up_bit+0x20/0x70 RSP <ffff880017b97be8> CR2: ffffc90008963690 Reproduce method (re-add a node):: Hot-add nodeA --> remove nodeA --> hot-add nodeA (panic) This seems an use-after-free problem, and the root cause is zone->wait_table was not set to *NULL* after free it in try_offline_node. When hot re-add a node, we will reuse the pgdat of it, so does the zone struct, and when add pages to the target zone, it will init the zone first (including the wait_table) if the zone is not initialized. The judgement of zone initialized is based on zone->wait_table: static inline bool zone_is_initialized(struct zone *zone) { return !!zone->wait_table; } so if we do not set the zone->wait_table to *NULL* after free it, the memory hotplug routine will skip the init of new zone when hot re-add the node, and the wait_table still points to the freed memory, then we will access the invalid address when trying to wake up the waiting people after the i/o operation with the page is done, such as mentioned above. Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Reported-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Reviewed by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1 parent 5879ae5
clk-s2mps11.c
/*
* clk-s2mps11.c - Clock driver for S2MPS11.
*
* Copyright (C) 2013,2014 Samsung Electornics
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/
#include <linux/module.h>
#include <linux/err.h>
#include <linux/of.h>
#include <linux/clkdev.h>
#include <linux/regmap.h>
#include <linux/clk-provider.h>
#include <linux/platform_device.h>
#include <linux/mfd/samsung/s2mps11.h>
#include <linux/mfd/samsung/s2mps13.h>
#include <linux/mfd/samsung/s2mps14.h>
#include <linux/mfd/samsung/s5m8767.h>
#include <linux/mfd/samsung/core.h>
#define s2mps11_name(a) (a->hw.init->name)
static struct clk **clk_table;
static struct clk_onecell_data clk_data;
enum {
S2MPS11_CLK_AP = 0,
S2MPS11_CLK_CP,
S2MPS11_CLK_BT,
S2MPS11_CLKS_NUM,
};
struct s2mps11_clk {
struct sec_pmic_dev *iodev;
struct device_node *clk_np;
struct clk_hw hw;
struct clk *clk;
struct clk_lookup *lookup;
u32 mask;
unsigned int reg;
};
static struct s2mps11_clk *to_s2mps11_clk(struct clk_hw *hw)
{
return container_of(hw, struct s2mps11_clk, hw);
}
static int s2mps11_clk_prepare(struct clk_hw *hw)
{
struct s2mps11_clk *s2mps11 = to_s2mps11_clk(hw);
int ret;
ret = regmap_update_bits(s2mps11->iodev->regmap_pmic,
s2mps11->reg,
s2mps11->mask, s2mps11->mask);
return ret;
}
static void s2mps11_clk_unprepare(struct clk_hw *hw)
{
struct s2mps11_clk *s2mps11 = to_s2mps11_clk(hw);
int ret;
ret = regmap_update_bits(s2mps11->iodev->regmap_pmic, s2mps11->reg,
s2mps11->mask, ~s2mps11->mask);
}
static int s2mps11_clk_is_prepared(struct clk_hw *hw)
{
int ret;
u32 val;
struct s2mps11_clk *s2mps11 = to_s2mps11_clk(hw);
ret = regmap_read(s2mps11->iodev->regmap_pmic,
s2mps11->reg, &val);
if (ret < 0)
return -EINVAL;
return val & s2mps11->mask;
}
static unsigned long s2mps11_clk_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
return 32768;
}
static struct clk_ops s2mps11_clk_ops = {
.prepare = s2mps11_clk_prepare,
.unprepare = s2mps11_clk_unprepare,
.is_prepared = s2mps11_clk_is_prepared,
.recalc_rate = s2mps11_clk_recalc_rate,
};
static struct clk_init_data s2mps11_clks_init[S2MPS11_CLKS_NUM] = {
[S2MPS11_CLK_AP] = {
.name = "s2mps11_ap",
.ops = &s2mps11_clk_ops,
.flags = CLK_IS_ROOT,
},
[S2MPS11_CLK_CP] = {
.name = "s2mps11_cp",
.ops = &s2mps11_clk_ops,
.flags = CLK_IS_ROOT,
},
[S2MPS11_CLK_BT] = {
.name = "s2mps11_bt",
.ops = &s2mps11_clk_ops,
.flags = CLK_IS_ROOT,
},
};
static struct clk_init_data s2mps13_clks_init[S2MPS11_CLKS_NUM] = {
[S2MPS11_CLK_AP] = {
.name = "s2mps13_ap",
.ops = &s2mps11_clk_ops,
.flags = CLK_IS_ROOT,
},
[S2MPS11_CLK_CP] = {
.name = "s2mps13_cp",
.ops = &s2mps11_clk_ops,
.flags = CLK_IS_ROOT,
},
[S2MPS11_CLK_BT] = {
.name = "s2mps13_bt",
.ops = &s2mps11_clk_ops,
.flags = CLK_IS_ROOT,
},
};
static struct clk_init_data s2mps14_clks_init[S2MPS11_CLKS_NUM] = {
[S2MPS11_CLK_AP] = {
.name = "s2mps14_ap",
.ops = &s2mps11_clk_ops,
.flags = CLK_IS_ROOT,
},
[S2MPS11_CLK_BT] = {
.name = "s2mps14_bt",
.ops = &s2mps11_clk_ops,
.flags = CLK_IS_ROOT,
},
};
static struct device_node *s2mps11_clk_parse_dt(struct platform_device *pdev,
struct clk_init_data *clks_init)
{
struct sec_pmic_dev *iodev = dev_get_drvdata(pdev->dev.parent);
struct device_node *clk_np;
int i;
if (!iodev->dev->of_node)
return ERR_PTR(-EINVAL);
clk_np = of_get_child_by_name(iodev->dev->of_node, "clocks");
if (!clk_np) {
dev_err(&pdev->dev, "could not find clock sub-node\n");
return ERR_PTR(-EINVAL);
}
for (i = 0; i < S2MPS11_CLKS_NUM; i++) {
if (!clks_init[i].name)
continue; /* Skip clocks not present in some devices */
of_property_read_string_index(clk_np, "clock-output-names", i,
&clks_init[i].name);
}
return clk_np;
}
static int s2mps11_clk_probe(struct platform_device *pdev)
{
struct sec_pmic_dev *iodev = dev_get_drvdata(pdev->dev.parent);
struct s2mps11_clk *s2mps11_clks, *s2mps11_clk;
unsigned int s2mps11_reg;
struct clk_init_data *clks_init;
int i, ret = 0;
s2mps11_clks = devm_kzalloc(&pdev->dev, sizeof(*s2mps11_clk) *
S2MPS11_CLKS_NUM, GFP_KERNEL);
if (!s2mps11_clks)
return -ENOMEM;
s2mps11_clk = s2mps11_clks;
clk_table = devm_kzalloc(&pdev->dev, sizeof(struct clk *) *
S2MPS11_CLKS_NUM, GFP_KERNEL);
if (!clk_table)
return -ENOMEM;
switch(platform_get_device_id(pdev)->driver_data) {
case S2MPS11X:
s2mps11_reg = S2MPS11_REG_RTC_CTRL;
clks_init = s2mps11_clks_init;
break;
case S2MPS13X:
s2mps11_reg = S2MPS13_REG_RTCCTRL;
clks_init = s2mps13_clks_init;
break;
case S2MPS14X:
s2mps11_reg = S2MPS14_REG_RTCCTRL;
clks_init = s2mps14_clks_init;
break;
case S5M8767X:
s2mps11_reg = S5M8767_REG_CTRL1;
clks_init = s2mps11_clks_init;
break;
default:
dev_err(&pdev->dev, "Invalid device type\n");
return -EINVAL;
}
/* Store clocks of_node in first element of s2mps11_clks array */
s2mps11_clks->clk_np = s2mps11_clk_parse_dt(pdev, clks_init);
if (IS_ERR(s2mps11_clks->clk_np))
return PTR_ERR(s2mps11_clks->clk_np);
for (i = 0; i < S2MPS11_CLKS_NUM; i++, s2mps11_clk++) {
if (!clks_init[i].name)
continue; /* Skip clocks not present in some devices */
s2mps11_clk->iodev = iodev;
s2mps11_clk->hw.init = &clks_init[i];
s2mps11_clk->mask = 1 << i;
s2mps11_clk->reg = s2mps11_reg;
s2mps11_clk->clk = devm_clk_register(&pdev->dev,
&s2mps11_clk->hw);
if (IS_ERR(s2mps11_clk->clk)) {
dev_err(&pdev->dev, "Fail to register : %s\n",
s2mps11_name(s2mps11_clk));
ret = PTR_ERR(s2mps11_clk->clk);
goto err_reg;
}
s2mps11_clk->lookup = clkdev_alloc(s2mps11_clk->clk,
s2mps11_name(s2mps11_clk), NULL);
if (!s2mps11_clk->lookup) {
ret = -ENOMEM;
goto err_lup;
}
clkdev_add(s2mps11_clk->lookup);
}
for (i = 0; i < S2MPS11_CLKS_NUM; i++) {
/* Skip clocks not present on S2MPS14 */
if (!clks_init[i].name)
continue;
clk_table[i] = s2mps11_clks[i].clk;
}
clk_data.clks = clk_table;
clk_data.clk_num = S2MPS11_CLKS_NUM;
of_clk_add_provider(s2mps11_clks->clk_np, of_clk_src_onecell_get,
&clk_data);
platform_set_drvdata(pdev, s2mps11_clks);
return ret;
err_lup:
devm_clk_unregister(&pdev->dev, s2mps11_clk->clk);
err_reg:
while (s2mps11_clk > s2mps11_clks) {
if (s2mps11_clk->lookup) {
clkdev_drop(s2mps11_clk->lookup);
devm_clk_unregister(&pdev->dev, s2mps11_clk->clk);
}
s2mps11_clk--;
}
return ret;
}
static int s2mps11_clk_remove(struct platform_device *pdev)
{
struct s2mps11_clk *s2mps11_clks = platform_get_drvdata(pdev);
int i;
of_clk_del_provider(s2mps11_clks[0].clk_np);
/* Drop the reference obtained in s2mps11_clk_parse_dt */
of_node_put(s2mps11_clks[0].clk_np);
for (i = 0; i < S2MPS11_CLKS_NUM; i++) {
/* Skip clocks not present on S2MPS14 */
if (!s2mps11_clks[i].lookup)
continue;
clkdev_drop(s2mps11_clks[i].lookup);
}
return 0;
}
static const struct platform_device_id s2mps11_clk_id[] = {
{ "s2mps11-clk", S2MPS11X},
{ "s2mps13-clk", S2MPS13X},
{ "s2mps14-clk", S2MPS14X},
{ "s5m8767-clk", S5M8767X},
{ },
};
MODULE_DEVICE_TABLE(platform, s2mps11_clk_id);
static struct platform_driver s2mps11_clk_driver = {
.driver = {
.name = "s2mps11-clk",
},
.probe = s2mps11_clk_probe,
.remove = s2mps11_clk_remove,
.id_table = s2mps11_clk_id,
};
static int __init s2mps11_clk_init(void)
{
return platform_driver_register(&s2mps11_clk_driver);
}
subsys_initcall(s2mps11_clk_init);
static void __init s2mps11_clk_cleanup(void)
{
platform_driver_unregister(&s2mps11_clk_driver);
}
module_exit(s2mps11_clk_cleanup);
MODULE_DESCRIPTION("S2MPS11 Clock Driver");
MODULE_AUTHOR("Yadwinder Singh Brar <yadi.brar@samsung.com>");
MODULE_LICENSE("GPL");
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...