Revision 85bd839983778fcd0c1c043327b14a046e979b39 authored by Gu Zheng on 10 June 2015, 18:14:43 UTC, committed by Linus Torvalds on 10 June 2015, 23:43:43 UTC
Izumi found the following oops when hot re-adding a node:
BUG: unable to handle kernel paging request at ffffc90008963690
IP: __wake_up_bit+0x20/0x70
Oops: 0000 [#1] SMP
CPU: 68 PID: 1237 Comm: rs:main Q:Reg Not tainted 4.1.0-rc5 #80
Hardware name: FUJITSU PRIMEQUEST2800E/SB, BIOS PRIMEQUEST 2000 Series BIOS Version 1.87 04/28/2015
task: ffff880838df8000 ti: ffff880017b94000 task.ti: ffff880017b94000
RIP: 0010:[<ffffffff810dff80>] [<ffffffff810dff80>] __wake_up_bit+0x20/0x70
RSP: 0018:ffff880017b97be8 EFLAGS: 00010246
RAX: ffffc90008963690 RBX: 00000000003c0000 RCX: 000000000000a4c9
RDX: 0000000000000000 RSI: ffffea101bffd500 RDI: ffffc90008963648
RBP: ffff880017b97c08 R08: 0000000002000020 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a0797c73800
R13: ffffea101bffd500 R14: 0000000000000001 R15: 00000000003c0000
FS: 00007fcc7ffff700(0000) GS:ffff880874800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffc90008963690 CR3: 0000000836761000 CR4: 00000000001407e0
Call Trace:
unlock_page+0x6d/0x70
generic_write_end+0x53/0xb0
xfs_vm_write_end+0x29/0x80 [xfs]
generic_perform_write+0x10a/0x1e0
xfs_file_buffered_aio_write+0x14d/0x3e0 [xfs]
xfs_file_write_iter+0x79/0x120 [xfs]
__vfs_write+0xd4/0x110
vfs_write+0xac/0x1c0
SyS_write+0x58/0xd0
system_call_fastpath+0x12/0x76
Code: 5d c3 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 48 83 ec 20 65 48 8b 04 25 28 00 00 00 48 89 45 f8 31 c0 48 8d 47 48 <48> 39 47 48 48 c7 45 e8 00 00 00 00 48 c7 45 f0 00 00 00 00 48
RIP [<ffffffff810dff80>] __wake_up_bit+0x20/0x70
RSP <ffff880017b97be8>
CR2: ffffc90008963690
Reproduce method (re-add a node)::
Hot-add nodeA --> remove nodeA --> hot-add nodeA (panic)
This seems an use-after-free problem, and the root cause is
zone->wait_table was not set to *NULL* after free it in
try_offline_node.
When hot re-add a node, we will reuse the pgdat of it, so does the zone
struct, and when add pages to the target zone, it will init the zone
first (including the wait_table) if the zone is not initialized. The
judgement of zone initialized is based on zone->wait_table:
static inline bool zone_is_initialized(struct zone *zone)
{
return !!zone->wait_table;
}
so if we do not set the zone->wait_table to *NULL* after free it, the
memory hotplug routine will skip the init of new zone when hot re-add
the node, and the wait_table still points to the freed memory, then we
will access the invalid address when trying to wake up the waiting
people after the i/o operation with the page is done, such as mentioned
above.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reported-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Reviewed by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1 parent 5879ae5
Makefile
#
# link order is important here
#
ccflags-y := -Idrivers/ide
ide-core-y += ide.o ide-ioctls.o ide-io.o ide-iops.o ide-lib.o ide-probe.o \
ide-taskfile.o ide-pm.o ide-park.o ide-sysfs.o ide-devsets.o \
ide-io-std.o ide-eh.o
# core IDE code
ide-core-$(CONFIG_IDE_XFER_MODE) += ide-pio-blacklist.o ide-xfer-mode.o
ide-core-$(CONFIG_IDE_TIMINGS) += ide-timings.o
ide-core-$(CONFIG_IDE_ATAPI) += ide-atapi.o
ide-core-$(CONFIG_BLK_DEV_IDEPCI) += setup-pci.o
ide-core-$(CONFIG_BLK_DEV_IDEDMA) += ide-dma.o
ide-core-$(CONFIG_BLK_DEV_IDEDMA_SFF) += ide-dma-sff.o
ide-core-$(CONFIG_IDE_PROC_FS) += ide-proc.o
ide-core-$(CONFIG_BLK_DEV_IDEACPI) += ide-acpi.o
ide-core-$(CONFIG_IDE_LEGACY) += ide-legacy.o
obj-$(CONFIG_IDE) += ide-core.o
obj-$(CONFIG_BLK_DEV_ALI14XX) += ali14xx.o
obj-$(CONFIG_BLK_DEV_UMC8672) += umc8672.o
obj-$(CONFIG_BLK_DEV_DTC2278) += dtc2278.o
obj-$(CONFIG_BLK_DEV_HT6560B) += ht6560b.o
obj-$(CONFIG_BLK_DEV_QD65XX) += qd65xx.o
obj-$(CONFIG_BLK_DEV_4DRIVES) += ide-4drives.o
obj-$(CONFIG_BLK_DEV_GAYLE) += gayle.o
obj-$(CONFIG_BLK_DEV_FALCON_IDE) += falconide.o
obj-$(CONFIG_BLK_DEV_MAC_IDE) += macide.o
obj-$(CONFIG_BLK_DEV_Q40IDE) += q40ide.o
obj-$(CONFIG_BLK_DEV_BUDDHA) += buddha.o
obj-$(CONFIG_BLK_DEV_AEC62XX) += aec62xx.o
obj-$(CONFIG_BLK_DEV_ALI15X3) += alim15x3.o
obj-$(CONFIG_BLK_DEV_AMD74XX) += amd74xx.o
obj-$(CONFIG_BLK_DEV_ATIIXP) += atiixp.o
obj-$(CONFIG_BLK_DEV_CMD64X) += cmd64x.o
obj-$(CONFIG_BLK_DEV_CS5520) += cs5520.o
obj-$(CONFIG_BLK_DEV_CS5530) += cs5530.o
obj-$(CONFIG_BLK_DEV_CS5535) += cs5535.o
obj-$(CONFIG_BLK_DEV_CS5536) += cs5536.o
obj-$(CONFIG_BLK_DEV_SC1200) += sc1200.o
obj-$(CONFIG_BLK_DEV_CY82C693) += cy82c693.o
obj-$(CONFIG_BLK_DEV_DELKIN) += delkin_cb.o
obj-$(CONFIG_BLK_DEV_HPT366) += hpt366.o
obj-$(CONFIG_BLK_DEV_IT8172) += it8172.o
obj-$(CONFIG_BLK_DEV_IT8213) += it8213.o
obj-$(CONFIG_BLK_DEV_IT821X) += it821x.o
obj-$(CONFIG_BLK_DEV_JMICRON) += jmicron.o
obj-$(CONFIG_BLK_DEV_NS87415) += ns87415.o
obj-$(CONFIG_BLK_DEV_OPTI621) += opti621.o
obj-$(CONFIG_BLK_DEV_PDC202XX_OLD) += pdc202xx_old.o
obj-$(CONFIG_BLK_DEV_PDC202XX_NEW) += pdc202xx_new.o
obj-$(CONFIG_BLK_DEV_PIIX) += piix.o
obj-$(CONFIG_BLK_DEV_RZ1000) += rz1000.o
obj-$(CONFIG_BLK_DEV_SVWKS) += serverworks.o
obj-$(CONFIG_BLK_DEV_SGIIOC4) += sgiioc4.o
obj-$(CONFIG_BLK_DEV_SIIMAGE) += siimage.o
obj-$(CONFIG_BLK_DEV_SIS5513) += sis5513.o
obj-$(CONFIG_BLK_DEV_SL82C105) += sl82c105.o
obj-$(CONFIG_BLK_DEV_SLC90E66) += slc90e66.o
obj-$(CONFIG_BLK_DEV_TC86C001) += tc86c001.o
obj-$(CONFIG_BLK_DEV_TRIFLEX) += triflex.o
obj-$(CONFIG_BLK_DEV_TRM290) += trm290.o
obj-$(CONFIG_BLK_DEV_VIA82CXXX) += via82cxxx.o
# Must appear at the end of the block
obj-$(CONFIG_BLK_DEV_GENERIC) += ide-pci-generic.o
obj-$(CONFIG_IDEPCI_PCIBUS_ORDER) += ide-scan-pci.o
obj-$(CONFIG_BLK_DEV_CMD640) += cmd640.o
obj-$(CONFIG_BLK_DEV_IDE_PMAC) += pmac.o
obj-$(CONFIG_IDE_GENERIC) += ide-generic.o
obj-$(CONFIG_BLK_DEV_IDEPNP) += ide-pnp.o
ide-gd_mod-y += ide-gd.o
ide-cd_mod-y += ide-cd.o ide-cd_ioctl.o ide-cd_verbose.o
ifeq ($(CONFIG_IDE_GD_ATA), y)
ide-gd_mod-y += ide-disk.o ide-disk_ioctl.o
ifeq ($(CONFIG_IDE_PROC_FS), y)
ide-gd_mod-y += ide-disk_proc.o
endif
endif
ifeq ($(CONFIG_IDE_GD_ATAPI), y)
ide-gd_mod-y += ide-floppy.o ide-floppy_ioctl.o
ifeq ($(CONFIG_IDE_PROC_FS), y)
ide-gd_mod-y += ide-floppy_proc.o
endif
endif
obj-$(CONFIG_IDE_GD) += ide-gd_mod.o
obj-$(CONFIG_BLK_DEV_IDECD) += ide-cd_mod.o
obj-$(CONFIG_BLK_DEV_IDETAPE) += ide-tape.o
obj-$(CONFIG_BLK_DEV_IDECS) += ide-cs.o
obj-$(CONFIG_BLK_DEV_PLATFORM) += ide_platform.o
obj-$(CONFIG_BLK_DEV_IDE_ICSIDE) += icside.o
obj-$(CONFIG_BLK_DEV_IDE_RAPIDE) += rapide.o
obj-$(CONFIG_BLK_DEV_PALMCHIP_BK3710) += palm_bk3710.o
obj-$(CONFIG_BLK_DEV_IDE_AU1XXX) += au1xxx-ide.o
obj-$(CONFIG_BLK_DEV_IDE_TX4938) += tx4938ide.o
obj-$(CONFIG_BLK_DEV_IDE_TX4939) += tx4939ide.o
Computing file changes ...
