Revision 8e37395c3a5dceff62a5010ebbbc107f4145935c authored by Linus Torvalds on 20 October 2021, 16:13:22 UTC, committed by Linus Torvalds on 20 October 2021, 16:13:22 UTC
Pull sound fixes from Takashi Iwai: "Again it became bigger than wished, unfortunately, as this contains quite a few ASoC fixes that came up a bit late. It also includes yet more HD- and USB-audio quirks: I decided to merge them now, as those are for stable, and we'll need them sooner or later. Although the volumes are a bit high, all changes are device-specific (and reasonably small) fixes, so it should be safe for the late rc" * tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: usb-audio: Fix microphone sound on Jieli webcam. ALSA: hda/realtek: Fixes HP Spectre x360 15-eb1xxx speakers ALSA: usb-audio: Provide quirk for Sennheiser GSP670 Headset ALSA: hda/realtek: Add quirk for Clevo PC50HS ALSA: usb-audio: add Schiit Hel device to quirk table ASoC: wm8960: Fix clock configuration on slave mode ASoC: cs42l42: Ensure 0dB full scale volume is used for headsets ASoC: soc-core: fix null-ptr-deref in snd_soc_del_component_unlocked() ASoC: codec: wcd938x: Add irq config support ASoC: DAPM: Fix missing kctl change notifications ASoC: Intel: bytcht_es8316: Utilize dev_err_probe() to avoid log saturation ASoC: Intel: bytcht_es8316: Switch to use gpiod_get_optional() ASoC: Intel: bytcht_es8316: Use temporary variable for struct device ASoC: Intel: bytcht_es8316: Get platform data via dev_get_platdata() ASoC: wcd938x: Fix jack detection issue ASoC: nau8824: Fix headphone vs headset, button-press detection no longer working ASoC: cs4341: Add SPI device ID table ASoC: pcm179x: Add missing entries SPI to device ID table ASoC: fsl_xcvr: Fix channel swap issue with ARC ASoC: pcm512x: Mend accesses to the I2S_1 and I2S_2 registers
adc128d818.rst
Kernel driver adc128d818
========================
Supported chips:
* Texas Instruments ADC818D818
Prefix: 'adc818d818'
Addresses scanned: I2C 0x1d, 0x1e, 0x1f, 0x2d, 0x2e, 0x2f
Datasheet: Publicly available at the TI website https://www.ti.com/
Author: Guenter Roeck
Description
-----------
This driver implements support for the Texas Instruments ADC128D818.
It is described as 'ADC System Monitor with Temperature Sensor'.
The ADC128D818 implements one temperature sensor and seven voltage sensors.
Temperatures are measured in degrees Celsius. There is one set of limits.
When the HOT Temperature Limit is crossed, this will cause an alarm that will
be reasserted until the temperature drops below the HOT Hysteresis.
Measurements are guaranteed between -55 and +125 degrees. The temperature
measurement has a resolution of 0.5 degrees; the limits have a resolution
of 1 degree.
Voltage sensors (also known as IN sensors) report their values in volts.
An alarm is triggered if the voltage has crossed a programmable minimum
or maximum limit. Note that minimum in this case always means 'closest to
zero'; this is important for negative voltage measurements. All voltage
inputs can measure voltages between 0 and 2.55 volts, with a resolution
of 0.625 mV.
If an alarm triggers, it will remain triggered until the hardware register
is read at least once. This means that the cause for the alarm may
already have disappeared by the time the alarm is read. The driver
caches the alarm status for each sensor until it is at least reported
once, to ensure that alarms are reported to user space.
The ADC128D818 only updates its values approximately once per second;
reading it more often will do no harm, but will return 'old' values.
In addition to the scanned address list, the chip can also be configured for
addresses 0x35 to 0x37. Those addresses are not scanned. You have to instantiate
the driver explicitly if the chip is configured for any of those addresses in
your system.
Computing file changes ...
