Revision 8e37395c3a5dceff62a5010ebbbc107f4145935c authored by Linus Torvalds on 20 October 2021, 16:13:22 UTC, committed by Linus Torvalds on 20 October 2021, 16:13:22 UTC
Pull sound fixes from Takashi Iwai: "Again it became bigger than wished, unfortunately, as this contains quite a few ASoC fixes that came up a bit late. It also includes yet more HD- and USB-audio quirks: I decided to merge them now, as those are for stable, and we'll need them sooner or later. Although the volumes are a bit high, all changes are device-specific (and reasonably small) fixes, so it should be safe for the late rc" * tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: usb-audio: Fix microphone sound on Jieli webcam. ALSA: hda/realtek: Fixes HP Spectre x360 15-eb1xxx speakers ALSA: usb-audio: Provide quirk for Sennheiser GSP670 Headset ALSA: hda/realtek: Add quirk for Clevo PC50HS ALSA: usb-audio: add Schiit Hel device to quirk table ASoC: wm8960: Fix clock configuration on slave mode ASoC: cs42l42: Ensure 0dB full scale volume is used for headsets ASoC: soc-core: fix null-ptr-deref in snd_soc_del_component_unlocked() ASoC: codec: wcd938x: Add irq config support ASoC: DAPM: Fix missing kctl change notifications ASoC: Intel: bytcht_es8316: Utilize dev_err_probe() to avoid log saturation ASoC: Intel: bytcht_es8316: Switch to use gpiod_get_optional() ASoC: Intel: bytcht_es8316: Use temporary variable for struct device ASoC: Intel: bytcht_es8316: Get platform data via dev_get_platdata() ASoC: wcd938x: Fix jack detection issue ASoC: nau8824: Fix headphone vs headset, button-press detection no longer working ASoC: cs4341: Add SPI device ID table ASoC: pcm179x: Add missing entries SPI to device ID table ASoC: fsl_xcvr: Fix channel swap issue with ARC ASoC: pcm512x: Mend accesses to the I2S_1 and I2S_2 registers
ltc4260.rst
Kernel driver ltc4260
=====================
Supported chips:
* Linear Technology LTC4260
Prefix: 'ltc4260'
Addresses scanned: -
Datasheet:
http://cds.linear.com/docs/en/datasheet/4260fc.pdf
Author: Guenter Roeck <linux@roeck-us.net>
Description
-----------
The LTC4260 Hot Swap controller allows a board to be safely inserted
and removed from a live backplane.
Usage Notes
-----------
This driver does not probe for LTC4260 devices, since there is no register
which can be safely used to identify the chip. You will have to instantiate
the devices explicitly.
Example: the following will load the driver for an LTC4260 at address 0x10
on I2C bus #1::
$ modprobe ltc4260
$ echo ltc4260 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
Sysfs entries
-------------
Voltage readings provided by this driver are reported as obtained from the ADC
registers. If a set of voltage divider resistors is installed, calculate the
real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
value of the divider resistor against the measured voltage and R2 is the value
of the divider resistor against Ground.
Current reading provided by this driver is reported as obtained from the ADC
Current Sense register. The reported value assumes that a 1 mOhm sense resistor
is installed. If a different sense resistor is installed, calculate the real
current by dividing the reported value by the sense resistor value in mOhm.
======================= =======================
in1_input SOURCE voltage (mV)
in1_min_alarm Undervoltage alarm
in1_max_alarm Overvoltage alarm
in2_input ADIN voltage (mV)
in2_alarm Power bad alarm
curr1_input SENSE current (mA)
curr1_alarm SENSE overcurrent alarm
======================= =======================
Computing file changes ...
