Revision 8e37395c3a5dceff62a5010ebbbc107f4145935c authored by Linus Torvalds on 20 October 2021, 16:13:22 UTC, committed by Linus Torvalds on 20 October 2021, 16:13:22 UTC
Pull sound fixes from Takashi Iwai: "Again it became bigger than wished, unfortunately, as this contains quite a few ASoC fixes that came up a bit late. It also includes yet more HD- and USB-audio quirks: I decided to merge them now, as those are for stable, and we'll need them sooner or later. Although the volumes are a bit high, all changes are device-specific (and reasonably small) fixes, so it should be safe for the late rc" * tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: usb-audio: Fix microphone sound on Jieli webcam. ALSA: hda/realtek: Fixes HP Spectre x360 15-eb1xxx speakers ALSA: usb-audio: Provide quirk for Sennheiser GSP670 Headset ALSA: hda/realtek: Add quirk for Clevo PC50HS ALSA: usb-audio: add Schiit Hel device to quirk table ASoC: wm8960: Fix clock configuration on slave mode ASoC: cs42l42: Ensure 0dB full scale volume is used for headsets ASoC: soc-core: fix null-ptr-deref in snd_soc_del_component_unlocked() ASoC: codec: wcd938x: Add irq config support ASoC: DAPM: Fix missing kctl change notifications ASoC: Intel: bytcht_es8316: Utilize dev_err_probe() to avoid log saturation ASoC: Intel: bytcht_es8316: Switch to use gpiod_get_optional() ASoC: Intel: bytcht_es8316: Use temporary variable for struct device ASoC: Intel: bytcht_es8316: Get platform data via dev_get_platdata() ASoC: wcd938x: Fix jack detection issue ASoC: nau8824: Fix headphone vs headset, button-press detection no longer working ASoC: cs4341: Add SPI device ID table ASoC: pcm179x: Add missing entries SPI to device ID table ASoC: fsl_xcvr: Fix channel swap issue with ARC ASoC: pcm512x: Mend accesses to the I2S_1 and I2S_2 registers
shtc1.rst
Kernel driver shtc1
===================
Supported chips:
* Sensirion SHTC1
Prefix: 'shtc1'
Addresses scanned: none
Datasheet: https://www.sensirion.com/file/datasheet_shtc1
* Sensirion SHTW1
Prefix: 'shtw1'
Addresses scanned: none
Datasheet: https://www.sensirion.com/file/datasheet_shtw1
* Sensirion SHTC3
Prefix: 'shtc3'
Addresses scanned: none
Datasheet: https://www.sensirion.com/file/datasheet_shtc3
Author:
Johannes Winkelmann <johannes.winkelmann@sensirion.com>
Description
-----------
This driver implements support for the Sensirion SHTC1, SHTW1, and SHTC3
chips, a humidity and temperature sensor. Temperature is measured in degrees
celsius, relative humidity is expressed as a percentage.
The device communicates with the I2C protocol. All sensors are set to I2C
address 0x70. See Documentation/i2c/instantiating-devices.rst for methods to
instantiate the device.
There are two options configurable by means of shtc1_platform_data:
1. blocking (pull the I2C clock line down while performing the measurement) or
non-blocking mode. Blocking mode will guarantee the fastest result but
the I2C bus will be busy during that time. By default, non-blocking mode
is used. Make sure clock-stretching works properly on your device if you
want to use blocking mode.
2. high or low accuracy. High accuracy is used by default and using it is
strongly recommended.
sysfs-Interface
---------------
temp1_input
- temperature input
humidity1_input
- humidity input
Computing file changes ...
