Revision 9a765881bf3dcd32847d7108cf48cb04a4ed993f authored by Bjørn Mork on 10 October 2016, 19:12:49 UTC, committed by David S. Miller on 13 October 2016, 14:05:06 UTC
The Quectel EC21 and EC25 need the same "set DTR" request as devices based on the MDM9230 chipset, but has no USB3 support. Our best guess is that the "set DTR" functionality depends on chipset and/or baseband firmware generation. But USB3 is still an optional feature. Since we cannot enable this unconditionally for all older devices, and there doesn't appear to be anything we can use in the USB descriptors to identify these chips, we are forced to use a device specific quirk flag. Reported-and-tested-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
1 parent 4013bee
dynamic_queue_limits.c
/*
* Dynamic byte queue limits. See include/linux/dynamic_queue_limits.h
*
* Copyright (c) 2011, Tom Herbert <therbert@google.com>
*/
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/jiffies.h>
#include <linux/dynamic_queue_limits.h>
#include <linux/compiler.h>
#include <linux/export.h>
#define POSDIFF(A, B) ((int)((A) - (B)) > 0 ? (A) - (B) : 0)
#define AFTER_EQ(A, B) ((int)((A) - (B)) >= 0)
/* Records completed count and recalculates the queue limit */
void dql_completed(struct dql *dql, unsigned int count)
{
unsigned int inprogress, prev_inprogress, limit;
unsigned int ovlimit, completed, num_queued;
bool all_prev_completed;
num_queued = ACCESS_ONCE(dql->num_queued);
/* Can't complete more than what's in queue */
BUG_ON(count > num_queued - dql->num_completed);
completed = dql->num_completed + count;
limit = dql->limit;
ovlimit = POSDIFF(num_queued - dql->num_completed, limit);
inprogress = num_queued - completed;
prev_inprogress = dql->prev_num_queued - dql->num_completed;
all_prev_completed = AFTER_EQ(completed, dql->prev_num_queued);
if ((ovlimit && !inprogress) ||
(dql->prev_ovlimit && all_prev_completed)) {
/*
* Queue considered starved if:
* - The queue was over-limit in the last interval,
* and there is no more data in the queue.
* OR
* - The queue was over-limit in the previous interval and
* when enqueuing it was possible that all queued data
* had been consumed. This covers the case when queue
* may have becomes starved between completion processing
* running and next time enqueue was scheduled.
*
* When queue is starved increase the limit by the amount
* of bytes both sent and completed in the last interval,
* plus any previous over-limit.
*/
limit += POSDIFF(completed, dql->prev_num_queued) +
dql->prev_ovlimit;
dql->slack_start_time = jiffies;
dql->lowest_slack = UINT_MAX;
} else if (inprogress && prev_inprogress && !all_prev_completed) {
/*
* Queue was not starved, check if the limit can be decreased.
* A decrease is only considered if the queue has been busy in
* the whole interval (the check above).
*
* If there is slack, the amount of execess data queued above
* the the amount needed to prevent starvation, the queue limit
* can be decreased. To avoid hysteresis we consider the
* minimum amount of slack found over several iterations of the
* completion routine.
*/
unsigned int slack, slack_last_objs;
/*
* Slack is the maximum of
* - The queue limit plus previous over-limit minus twice
* the number of objects completed. Note that two times
* number of completed bytes is a basis for an upper bound
* of the limit.
* - Portion of objects in the last queuing operation that
* was not part of non-zero previous over-limit. That is
* "round down" by non-overlimit portion of the last
* queueing operation.
*/
slack = POSDIFF(limit + dql->prev_ovlimit,
2 * (completed - dql->num_completed));
slack_last_objs = dql->prev_ovlimit ?
POSDIFF(dql->prev_last_obj_cnt, dql->prev_ovlimit) : 0;
slack = max(slack, slack_last_objs);
if (slack < dql->lowest_slack)
dql->lowest_slack = slack;
if (time_after(jiffies,
dql->slack_start_time + dql->slack_hold_time)) {
limit = POSDIFF(limit, dql->lowest_slack);
dql->slack_start_time = jiffies;
dql->lowest_slack = UINT_MAX;
}
}
/* Enforce bounds on limit */
limit = clamp(limit, dql->min_limit, dql->max_limit);
if (limit != dql->limit) {
dql->limit = limit;
ovlimit = 0;
}
dql->adj_limit = limit + completed;
dql->prev_ovlimit = ovlimit;
dql->prev_last_obj_cnt = dql->last_obj_cnt;
dql->num_completed = completed;
dql->prev_num_queued = num_queued;
}
EXPORT_SYMBOL(dql_completed);
void dql_reset(struct dql *dql)
{
/* Reset all dynamic values */
dql->limit = 0;
dql->num_queued = 0;
dql->num_completed = 0;
dql->last_obj_cnt = 0;
dql->prev_num_queued = 0;
dql->prev_last_obj_cnt = 0;
dql->prev_ovlimit = 0;
dql->lowest_slack = UINT_MAX;
dql->slack_start_time = jiffies;
}
EXPORT_SYMBOL(dql_reset);
int dql_init(struct dql *dql, unsigned hold_time)
{
dql->max_limit = DQL_MAX_LIMIT;
dql->min_limit = 0;
dql->slack_hold_time = hold_time;
dql_reset(dql);
return 0;
}
EXPORT_SYMBOL(dql_init);
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...