Revision a20303725ec31ea0fcf498f1885b1d4245a4ee56 authored by Robin Murphy on 10 August 2016, 12:02:17 UTC, committed by Arnd Bergmann on 10 August 2016, 20:58:09 UTC
Clearly QEMU is very permissive in how its PL310 model may be set up,
but the real hardware turns out to be far more particular about things
actually being correct. Fix up the DT description so that the real
thing actually boots:

- The arm,data-latency and arm,tag-latency properties need 3 cells to
  be valid, otherwise we end up retaining the default 8-cycle latencies
  which leads pretty quickly to lockup.
- The arm,dirty-latency property is only relevant to L210/L220, so get
  rid of it.
- The cache geometry override also leads to lockup and/or general
  misbehaviour. Irritatingly, the manual doesn't state the actual PL310
  configuration, but based on the boardfile code and poking registers
  from the Boot Monitor, it would seem to be 8 sets of 16KB ways.

With that, we can successfully boot to enjoy the fun of mismatched FPUs...

Cc: stable@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1 parent b5c86b7
Raw File
bebob_maudio.c
/*
 * bebob_maudio.c - a part of driver for BeBoB based devices
 *
 * Copyright (c) 2013-2014 Takashi Sakamoto
 *
 * Licensed under the terms of the GNU General Public License, version 2.
 */

#include "./bebob.h"
#include <sound/control.h>

/*
 * Just powering on, Firewire 410/Audiophile/1814 and ProjectMix I/O wait to
 * download firmware blob. To enable these devices, drivers should upload
 * firmware blob and send a command to initialize configuration to factory
 * settings when completing uploading. Then these devices generate bus reset
 * and are recognized as new devices with the firmware.
 *
 * But with firmware version 5058 or later, the firmware is stored to flash
 * memory in the device and drivers can tell bootloader to load the firmware
 * by sending a cue. This cue must be sent one time.
 *
 * For streaming, both of output and input streams are needed for Firewire 410
 * and Ozonic. The single stream is OK for the other devices even if the clock
 * source is not SYT-Match (I note no devices use SYT-Match).
 *
 * Without streaming, the devices except for Firewire Audiophile can mix any
 * input and output. For this reason, Audiophile cannot be used as standalone
 * mixer.
 *
 * Firewire 1814 and ProjectMix I/O uses special firmware. It will be freezed
 * when receiving any commands which the firmware can't understand. These
 * devices utilize completely different system to control. It is some
 * write-transaction directly into a certain address. All of addresses for mixer
 * functionality is between 0xffc700700000 to 0xffc70070009c.
 */

/* Offset from information register */
#define INFO_OFFSET_SW_DATE	0x20

/* Bootloader Protocol Version 1 */
#define MAUDIO_BOOTLOADER_CUE1	0x00000001
/*
 * Initializing configuration to factory settings (= 0x1101), (swapped in line),
 * Command code is zero (= 0x00),
 * the number of operands is zero (= 0x00)(at least significant byte)
 */
#define MAUDIO_BOOTLOADER_CUE2	0x01110000
/* padding */
#define MAUDIO_BOOTLOADER_CUE3	0x00000000

#define MAUDIO_SPECIFIC_ADDRESS	0xffc700000000ULL

#define METER_OFFSET		0x00600000

/* some device has sync info after metering data */
#define METER_SIZE_SPECIAL	84	/* with sync info */
#define METER_SIZE_FW410	76	/* with sync info */
#define METER_SIZE_AUDIOPHILE	60	/* with sync info */
#define METER_SIZE_SOLO		52	/* with sync info */
#define METER_SIZE_OZONIC	48
#define METER_SIZE_NRV10	80

/* labels for metering */
#define ANA_IN		"Analog In"
#define ANA_OUT		"Analog Out"
#define DIG_IN		"Digital In"
#define SPDIF_IN	"S/PDIF In"
#define ADAT_IN		"ADAT In"
#define DIG_OUT		"Digital Out"
#define SPDIF_OUT	"S/PDIF Out"
#define ADAT_OUT	"ADAT Out"
#define STRM_IN		"Stream In"
#define AUX_OUT		"Aux Out"
#define HP_OUT		"HP Out"
/* for NRV */
#define UNKNOWN_METER	"Unknown"

struct special_params {
	bool is1814;
	unsigned int clk_src;
	unsigned int dig_in_fmt;
	unsigned int dig_out_fmt;
	unsigned int clk_lock;
	struct snd_ctl_elem_id *ctl_id_sync;
};

/*
 * For some M-Audio devices, this module just send cue to load firmware. After
 * loading, the device generates bus reset and newly detected.
 *
 * If we make any transactions to load firmware, the operation may failed.
 */
int snd_bebob_maudio_load_firmware(struct fw_unit *unit)
{
	struct fw_device *device = fw_parent_device(unit);
	int err, rcode;
	u64 date;
	__le32 cues[3] = {
		cpu_to_le32(MAUDIO_BOOTLOADER_CUE1),
		cpu_to_le32(MAUDIO_BOOTLOADER_CUE2),
		cpu_to_le32(MAUDIO_BOOTLOADER_CUE3)
	};

	/* check date of software used to build */
	err = snd_bebob_read_block(unit, INFO_OFFSET_SW_DATE,
				   &date, sizeof(u64));
	if (err < 0)
		goto end;
	/*
	 * firmware version 5058 or later has date later than "20070401", but
	 * 'date' is not null-terminated.
	 */
	if (date < 0x3230303730343031LL) {
		dev_err(&unit->device,
			"Use firmware version 5058 or later\n");
		err = -ENOSYS;
		goto end;
	}

	rcode = fw_run_transaction(device->card, TCODE_WRITE_BLOCK_REQUEST,
				   device->node_id, device->generation,
				   device->max_speed, BEBOB_ADDR_REG_REQ,
				   cues, sizeof(cues));
	if (rcode != RCODE_COMPLETE) {
		dev_err(&unit->device,
			"Failed to send a cue to load firmware\n");
		err = -EIO;
	}
end:
	return err;
}

static inline int
get_meter(struct snd_bebob *bebob, void *buf, unsigned int size)
{
	return snd_fw_transaction(bebob->unit, TCODE_READ_BLOCK_REQUEST,
				  MAUDIO_SPECIFIC_ADDRESS + METER_OFFSET,
				  buf, size, 0);
}

static int
check_clk_sync(struct snd_bebob *bebob, unsigned int size, bool *sync)
{
	int err;
	u8 *buf;

	buf = kmalloc(size, GFP_KERNEL);
	if (buf == NULL)
		return -ENOMEM;

	err = get_meter(bebob, buf, size);
	if (err < 0)
		goto end;

	/* if synced, this value is the same as SFC of FDF in CIP header */
	*sync = (buf[size - 2] != 0xff);
end:
	kfree(buf);
	return err;
}

/*
 * dig_fmt: 0x00:S/PDIF, 0x01:ADAT
 * clk_lock: 0x00:unlock, 0x01:lock
 */
static int
avc_maudio_set_special_clk(struct snd_bebob *bebob, unsigned int clk_src,
			   unsigned int dig_in_fmt, unsigned int dig_out_fmt,
			   unsigned int clk_lock)
{
	struct special_params *params = bebob->maudio_special_quirk;
	int err;
	u8 *buf;

	if (amdtp_stream_running(&bebob->rx_stream) ||
	    amdtp_stream_running(&bebob->tx_stream))
		return -EBUSY;

	buf = kmalloc(12, GFP_KERNEL);
	if (buf == NULL)
		return -ENOMEM;

	buf[0]  = 0x00;		/* CONTROL */
	buf[1]  = 0xff;		/* UNIT */
	buf[2]  = 0x00;		/* vendor dependent */
	buf[3]  = 0x04;		/* company ID high */
	buf[4]  = 0x00;		/* company ID middle */
	buf[5]  = 0x04;		/* company ID low */
	buf[6]  = 0xff & clk_src;	/* clock source */
	buf[7]  = 0xff & dig_in_fmt;	/* input digital format */
	buf[8]  = 0xff & dig_out_fmt;	/* output digital format */
	buf[9]  = 0xff & clk_lock;	/* lock these settings */
	buf[10] = 0x00;		/* padding  */
	buf[11] = 0x00;		/* padding */

	err = fcp_avc_transaction(bebob->unit, buf, 12, buf, 12,
				  BIT(1) | BIT(2) | BIT(3) | BIT(4) |
				  BIT(5) | BIT(6) | BIT(7) | BIT(8) |
				  BIT(9));
	if ((err > 0) && (err < 10))
		err = -EIO;
	else if (buf[0] == 0x08) /* NOT IMPLEMENTED */
		err = -ENOSYS;
	else if (buf[0] == 0x0a) /* REJECTED */
		err = -EINVAL;
	if (err < 0)
		goto end;

	params->clk_src		= buf[6];
	params->dig_in_fmt	= buf[7];
	params->dig_out_fmt	= buf[8];
	params->clk_lock	= buf[9];

	if (params->ctl_id_sync)
		snd_ctl_notify(bebob->card, SNDRV_CTL_EVENT_MASK_VALUE,
			       params->ctl_id_sync);

	err = 0;
end:
	kfree(buf);
	return err;
}
static void
special_stream_formation_set(struct snd_bebob *bebob)
{
	static const unsigned int ch_table[2][2][3] = {
		/* AMDTP_OUT_STREAM */
		{ {  6,  6,  4 },	/* SPDIF */
		  { 12,  8,  4 } },	/* ADAT */
		/* AMDTP_IN_STREAM */
		{ { 10, 10,  2 },	/* SPDIF */
		  { 16, 12,  2 } }	/* ADAT */
	};
	struct special_params *params = bebob->maudio_special_quirk;
	unsigned int i, max;

	max = SND_BEBOB_STRM_FMT_ENTRIES - 1;
	if (!params->is1814)
		max -= 2;

	for (i = 0; i < max; i++) {
		bebob->tx_stream_formations[i + 1].pcm =
			ch_table[AMDTP_IN_STREAM][params->dig_in_fmt][i / 2];
		bebob->tx_stream_formations[i + 1].midi = 1;

		bebob->rx_stream_formations[i + 1].pcm =
			ch_table[AMDTP_OUT_STREAM][params->dig_out_fmt][i / 2];
		bebob->rx_stream_formations[i + 1].midi = 1;
	}
}

static int add_special_controls(struct snd_bebob *bebob);
int
snd_bebob_maudio_special_discover(struct snd_bebob *bebob, bool is1814)
{
	struct special_params *params;
	int err;

	params = kzalloc(sizeof(struct special_params), GFP_KERNEL);
	if (params == NULL)
		return -ENOMEM;

	mutex_lock(&bebob->mutex);

	bebob->maudio_special_quirk = (void *)params;
	params->is1814 = is1814;

	/* initialize these parameters because driver is not allowed to ask */
	bebob->rx_stream.context = ERR_PTR(-1);
	bebob->tx_stream.context = ERR_PTR(-1);
	err = avc_maudio_set_special_clk(bebob, 0x03, 0x00, 0x00, 0x00);
	if (err < 0) {
		dev_err(&bebob->unit->device,
			"fail to initialize clock params: %d\n", err);
		goto end;
	}

	err = add_special_controls(bebob);
	if (err < 0)
		goto end;

	special_stream_formation_set(bebob);

	if (params->is1814) {
		bebob->midi_input_ports = 1;
		bebob->midi_output_ports = 1;
	} else {
		bebob->midi_input_ports = 2;
		bebob->midi_output_ports = 2;
	}
end:
	if (err < 0) {
		kfree(params);
		bebob->maudio_special_quirk = NULL;
	}
	mutex_unlock(&bebob->mutex);
	return err;
}

/* Input plug shows actual rate. Output plug is needless for this purpose. */
static int special_get_rate(struct snd_bebob *bebob, unsigned int *rate)
{
	int err, trials;

	trials = 0;
	do {
		err = avc_general_get_sig_fmt(bebob->unit, rate,
					      AVC_GENERAL_PLUG_DIR_IN, 0);
	} while (err == -EAGAIN && ++trials < 3);

	return err;
}
static int special_set_rate(struct snd_bebob *bebob, unsigned int rate)
{
	struct special_params *params = bebob->maudio_special_quirk;
	int err;

	err = avc_general_set_sig_fmt(bebob->unit, rate,
				      AVC_GENERAL_PLUG_DIR_OUT, 0);
	if (err < 0)
		goto end;

	/*
	 * Just after changing sampling rate for output, a followed command
	 * for input is easy to fail. This is a workaround fot this issue.
	 */
	msleep(100);

	err = avc_general_set_sig_fmt(bebob->unit, rate,
				      AVC_GENERAL_PLUG_DIR_IN, 0);
	if (err < 0)
		goto end;

	if (params->ctl_id_sync)
		snd_ctl_notify(bebob->card, SNDRV_CTL_EVENT_MASK_VALUE,
			       params->ctl_id_sync);
end:
	return err;
}

/* Clock source control for special firmware */
static enum snd_bebob_clock_type special_clk_types[] = {
	SND_BEBOB_CLOCK_TYPE_INTERNAL,	/* With digital mute */
	SND_BEBOB_CLOCK_TYPE_EXTERNAL,	/* SPDIF/ADAT */
	SND_BEBOB_CLOCK_TYPE_EXTERNAL,	/* Word Clock */
	SND_BEBOB_CLOCK_TYPE_INTERNAL,
};
static int special_clk_get(struct snd_bebob *bebob, unsigned int *id)
{
	struct special_params *params = bebob->maudio_special_quirk;
	*id = params->clk_src;
	return 0;
}
static int special_clk_ctl_info(struct snd_kcontrol *kctl,
				struct snd_ctl_elem_info *einf)
{
	static const char *const special_clk_labels[] = {
		"Internal with Digital Mute",
		"Digital",
		"Word Clock",
		"Internal"
	};
	return snd_ctl_enum_info(einf, 1, ARRAY_SIZE(special_clk_types),
				 special_clk_labels);
}
static int special_clk_ctl_get(struct snd_kcontrol *kctl,
			       struct snd_ctl_elem_value *uval)
{
	struct snd_bebob *bebob = snd_kcontrol_chip(kctl);
	struct special_params *params = bebob->maudio_special_quirk;
	uval->value.enumerated.item[0] = params->clk_src;
	return 0;
}
static int special_clk_ctl_put(struct snd_kcontrol *kctl,
			       struct snd_ctl_elem_value *uval)
{
	struct snd_bebob *bebob = snd_kcontrol_chip(kctl);
	struct special_params *params = bebob->maudio_special_quirk;
	int err, id;

	id = uval->value.enumerated.item[0];
	if (id >= ARRAY_SIZE(special_clk_types))
		return -EINVAL;

	mutex_lock(&bebob->mutex);

	err = avc_maudio_set_special_clk(bebob, id,
					 params->dig_in_fmt,
					 params->dig_out_fmt,
					 params->clk_lock);
	mutex_unlock(&bebob->mutex);

	if (err >= 0)
		err = 1;

	return err;
}
static struct snd_kcontrol_new special_clk_ctl = {
	.name	= "Clock Source",
	.iface	= SNDRV_CTL_ELEM_IFACE_MIXER,
	.access	= SNDRV_CTL_ELEM_ACCESS_READWRITE,
	.info	= special_clk_ctl_info,
	.get	= special_clk_ctl_get,
	.put	= special_clk_ctl_put
};

/* Clock synchronization control for special firmware */
static int special_sync_ctl_info(struct snd_kcontrol *kctl,
				 struct snd_ctl_elem_info *einf)
{
	einf->type = SNDRV_CTL_ELEM_TYPE_BOOLEAN;
	einf->count = 1;
	einf->value.integer.min = 0;
	einf->value.integer.max = 1;

	return 0;
}
static int special_sync_ctl_get(struct snd_kcontrol *kctl,
				struct snd_ctl_elem_value *uval)
{
	struct snd_bebob *bebob = snd_kcontrol_chip(kctl);
	int err;
	bool synced = 0;

	err = check_clk_sync(bebob, METER_SIZE_SPECIAL, &synced);
	if (err >= 0)
		uval->value.integer.value[0] = synced;

	return 0;
}
static struct snd_kcontrol_new special_sync_ctl = {
	.name	= "Sync Status",
	.iface	= SNDRV_CTL_ELEM_IFACE_MIXER,
	.access	= SNDRV_CTL_ELEM_ACCESS_READ,
	.info	= special_sync_ctl_info,
	.get	= special_sync_ctl_get,
};

/* Digital input interface control for special firmware */
static const char *const special_dig_in_iface_labels[] = {
	"S/PDIF Optical", "S/PDIF Coaxial", "ADAT Optical"
};
static int special_dig_in_iface_ctl_info(struct snd_kcontrol *kctl,
					 struct snd_ctl_elem_info *einf)
{
	return snd_ctl_enum_info(einf, 1,
				 ARRAY_SIZE(special_dig_in_iface_labels),
				 special_dig_in_iface_labels);
}
static int special_dig_in_iface_ctl_get(struct snd_kcontrol *kctl,
					struct snd_ctl_elem_value *uval)
{
	struct snd_bebob *bebob = snd_kcontrol_chip(kctl);
	struct special_params *params = bebob->maudio_special_quirk;
	unsigned int dig_in_iface;
	int err, val;

	mutex_lock(&bebob->mutex);

	err = avc_audio_get_selector(bebob->unit, 0x00, 0x04,
				     &dig_in_iface);
	if (err < 0) {
		dev_err(&bebob->unit->device,
			"fail to get digital input interface: %d\n", err);
		goto end;
	}

	/* encoded id for user value */
	val = (params->dig_in_fmt << 1) | (dig_in_iface & 0x01);

	/* for ADAT Optical */
	if (val > 2)
		val = 2;

	uval->value.enumerated.item[0] = val;
end:
	mutex_unlock(&bebob->mutex);
	return err;
}
static int special_dig_in_iface_ctl_set(struct snd_kcontrol *kctl,
					struct snd_ctl_elem_value *uval)
{
	struct snd_bebob *bebob = snd_kcontrol_chip(kctl);
	struct special_params *params = bebob->maudio_special_quirk;
	unsigned int id, dig_in_fmt, dig_in_iface;
	int err;

	id = uval->value.enumerated.item[0];
	if (id >= ARRAY_SIZE(special_dig_in_iface_labels))
		return -EINVAL;

	/* decode user value */
	dig_in_fmt = (id >> 1) & 0x01;
	dig_in_iface = id & 0x01;

	mutex_lock(&bebob->mutex);

	err = avc_maudio_set_special_clk(bebob,
					 params->clk_src,
					 dig_in_fmt,
					 params->dig_out_fmt,
					 params->clk_lock);
	if (err < 0)
		goto end;

	/* For ADAT, optical interface is only available. */
	if (params->dig_in_fmt > 0) {
		err = 1;
		goto end;
	}

	/* For S/PDIF, optical/coaxial interfaces are selectable. */
	err = avc_audio_set_selector(bebob->unit, 0x00, 0x04, dig_in_iface);
	if (err < 0)
		dev_err(&bebob->unit->device,
			"fail to set digital input interface: %d\n", err);
	err = 1;
end:
	special_stream_formation_set(bebob);
	mutex_unlock(&bebob->mutex);
	return err;
}
static struct snd_kcontrol_new special_dig_in_iface_ctl = {
	.name	= "Digital Input Interface",
	.iface	= SNDRV_CTL_ELEM_IFACE_MIXER,
	.access	= SNDRV_CTL_ELEM_ACCESS_READWRITE,
	.info	= special_dig_in_iface_ctl_info,
	.get	= special_dig_in_iface_ctl_get,
	.put	= special_dig_in_iface_ctl_set
};

/* Digital output interface control for special firmware */
static const char *const special_dig_out_iface_labels[] = {
	"S/PDIF Optical and Coaxial", "ADAT Optical"
};
static int special_dig_out_iface_ctl_info(struct snd_kcontrol *kctl,
					  struct snd_ctl_elem_info *einf)
{
	return snd_ctl_enum_info(einf, 1,
				 ARRAY_SIZE(special_dig_out_iface_labels),
				 special_dig_out_iface_labels);
}
static int special_dig_out_iface_ctl_get(struct snd_kcontrol *kctl,
					 struct snd_ctl_elem_value *uval)
{
	struct snd_bebob *bebob = snd_kcontrol_chip(kctl);
	struct special_params *params = bebob->maudio_special_quirk;
	mutex_lock(&bebob->mutex);
	uval->value.enumerated.item[0] = params->dig_out_fmt;
	mutex_unlock(&bebob->mutex);
	return 0;
}
static int special_dig_out_iface_ctl_set(struct snd_kcontrol *kctl,
					 struct snd_ctl_elem_value *uval)
{
	struct snd_bebob *bebob = snd_kcontrol_chip(kctl);
	struct special_params *params = bebob->maudio_special_quirk;
	unsigned int id;
	int err;

	id = uval->value.enumerated.item[0];
	if (id >= ARRAY_SIZE(special_dig_out_iface_labels))
		return -EINVAL;

	mutex_lock(&bebob->mutex);

	err = avc_maudio_set_special_clk(bebob,
					 params->clk_src,
					 params->dig_in_fmt,
					 id, params->clk_lock);
	if (err >= 0) {
		special_stream_formation_set(bebob);
		err = 1;
	}

	mutex_unlock(&bebob->mutex);
	return err;
}
static struct snd_kcontrol_new special_dig_out_iface_ctl = {
	.name	= "Digital Output Interface",
	.iface	= SNDRV_CTL_ELEM_IFACE_MIXER,
	.access	= SNDRV_CTL_ELEM_ACCESS_READWRITE,
	.info	= special_dig_out_iface_ctl_info,
	.get	= special_dig_out_iface_ctl_get,
	.put	= special_dig_out_iface_ctl_set
};

static int add_special_controls(struct snd_bebob *bebob)
{
	struct snd_kcontrol *kctl;
	struct special_params *params = bebob->maudio_special_quirk;
	int err;

	kctl = snd_ctl_new1(&special_clk_ctl, bebob);
	err = snd_ctl_add(bebob->card, kctl);
	if (err < 0)
		goto end;

	kctl = snd_ctl_new1(&special_sync_ctl, bebob);
	err = snd_ctl_add(bebob->card, kctl);
	if (err < 0)
		goto end;
	params->ctl_id_sync = &kctl->id;

	kctl = snd_ctl_new1(&special_dig_in_iface_ctl, bebob);
	err = snd_ctl_add(bebob->card, kctl);
	if (err < 0)
		goto end;

	kctl = snd_ctl_new1(&special_dig_out_iface_ctl, bebob);
	err = snd_ctl_add(bebob->card, kctl);
end:
	return err;
}

/* Hardware metering for special firmware */
static const char *const special_meter_labels[] = {
	ANA_IN, ANA_IN, ANA_IN, ANA_IN,
	SPDIF_IN,
	ADAT_IN, ADAT_IN, ADAT_IN, ADAT_IN,
	ANA_OUT, ANA_OUT,
	SPDIF_OUT,
	ADAT_OUT, ADAT_OUT, ADAT_OUT, ADAT_OUT,
	HP_OUT, HP_OUT,
	AUX_OUT
};
static int
special_meter_get(struct snd_bebob *bebob, u32 *target, unsigned int size)
{
	__be16 *buf;
	unsigned int i, c, channels;
	int err;

	channels = ARRAY_SIZE(special_meter_labels) * 2;
	if (size < channels * sizeof(u32))
		return -EINVAL;

	/* omit last 4 bytes because it's clock info. */
	buf = kmalloc(METER_SIZE_SPECIAL - 4, GFP_KERNEL);
	if (buf == NULL)
		return -ENOMEM;

	err = get_meter(bebob, (void *)buf, METER_SIZE_SPECIAL - 4);
	if (err < 0)
		goto end;

	/* Its format is u16 and some channels are unknown. */
	i = 0;
	for (c = 2; c < channels + 2; c++)
		target[i++] = be16_to_cpu(buf[c]) << 16;
end:
	kfree(buf);
	return err;
}

/* last 4 bytes are omitted because it's clock info. */
static const char *const fw410_meter_labels[] = {
	ANA_IN, DIG_IN,
	ANA_OUT, ANA_OUT, ANA_OUT, ANA_OUT, DIG_OUT,
	HP_OUT
};
static const char *const audiophile_meter_labels[] = {
	ANA_IN, DIG_IN,
	ANA_OUT, ANA_OUT, DIG_OUT,
	HP_OUT, AUX_OUT,
};
static const char *const solo_meter_labels[] = {
	ANA_IN, DIG_IN,
	STRM_IN, STRM_IN,
	ANA_OUT, DIG_OUT
};

/* no clock info */
static const char *const ozonic_meter_labels[] = {
	ANA_IN, ANA_IN,
	STRM_IN, STRM_IN,
	ANA_OUT, ANA_OUT
};
/* TODO: need testers. these positions are based on authour's assumption */
static const char *const nrv10_meter_labels[] = {
	ANA_IN, ANA_IN, ANA_IN, ANA_IN,
	DIG_IN,
	ANA_OUT, ANA_OUT, ANA_OUT, ANA_OUT,
	DIG_IN
};
static int
normal_meter_get(struct snd_bebob *bebob, u32 *buf, unsigned int size)
{
	const struct snd_bebob_meter_spec *spec = bebob->spec->meter;
	unsigned int c, channels;
	int err;

	channels = spec->num * 2;
	if (size < channels * sizeof(u32))
		return -EINVAL;

	err = get_meter(bebob, (void *)buf, size);
	if (err < 0)
		goto end;

	for (c = 0; c < channels; c++)
		be32_to_cpus(&buf[c]);

	/* swap stream channels because inverted */
	if (spec->labels == solo_meter_labels) {
		swap(buf[4], buf[6]);
		swap(buf[5], buf[7]);
	}
end:
	return err;
}

/* for special customized devices */
static const struct snd_bebob_rate_spec special_rate_spec = {
	.get	= &special_get_rate,
	.set	= &special_set_rate,
};
static const struct snd_bebob_clock_spec special_clk_spec = {
	.num	= ARRAY_SIZE(special_clk_types),
	.types	= special_clk_types,
	.get	= &special_clk_get,
};
static const struct snd_bebob_meter_spec special_meter_spec = {
	.num	= ARRAY_SIZE(special_meter_labels),
	.labels	= special_meter_labels,
	.get	= &special_meter_get
};
const struct snd_bebob_spec maudio_special_spec = {
	.clock	= &special_clk_spec,
	.rate	= &special_rate_spec,
	.meter	= &special_meter_spec
};

/* Firewire 410 specification */
static const struct snd_bebob_rate_spec usual_rate_spec = {
	.get	= &snd_bebob_stream_get_rate,
	.set	= &snd_bebob_stream_set_rate,
};
static const struct snd_bebob_meter_spec fw410_meter_spec = {
	.num	= ARRAY_SIZE(fw410_meter_labels),
	.labels	= fw410_meter_labels,
	.get	= &normal_meter_get
};
const struct snd_bebob_spec maudio_fw410_spec = {
	.clock	= NULL,
	.rate	= &usual_rate_spec,
	.meter	= &fw410_meter_spec
};

/* Firewire Audiophile specification */
static const struct snd_bebob_meter_spec audiophile_meter_spec = {
	.num	= ARRAY_SIZE(audiophile_meter_labels),
	.labels	= audiophile_meter_labels,
	.get	= &normal_meter_get
};
const struct snd_bebob_spec maudio_audiophile_spec = {
	.clock	= NULL,
	.rate	= &usual_rate_spec,
	.meter	= &audiophile_meter_spec
};

/* Firewire Solo specification */
static const struct snd_bebob_meter_spec solo_meter_spec = {
	.num	= ARRAY_SIZE(solo_meter_labels),
	.labels	= solo_meter_labels,
	.get	= &normal_meter_get
};
const struct snd_bebob_spec maudio_solo_spec = {
	.clock	= NULL,
	.rate	= &usual_rate_spec,
	.meter	= &solo_meter_spec
};

/* Ozonic specification */
static const struct snd_bebob_meter_spec ozonic_meter_spec = {
	.num	= ARRAY_SIZE(ozonic_meter_labels),
	.labels	= ozonic_meter_labels,
	.get	= &normal_meter_get
};
const struct snd_bebob_spec maudio_ozonic_spec = {
	.clock	= NULL,
	.rate	= &usual_rate_spec,
	.meter	= &ozonic_meter_spec
};

/* NRV10 specification */
static const struct snd_bebob_meter_spec nrv10_meter_spec = {
	.num	= ARRAY_SIZE(nrv10_meter_labels),
	.labels	= nrv10_meter_labels,
	.get	= &normal_meter_get
};
const struct snd_bebob_spec maudio_nrv10_spec = {
	.clock	= NULL,
	.rate	= &usual_rate_spec,
	.meter	= &nrv10_meter_spec
};
back to top