Revision aab7a2414ba0d5c3d0571a90031b535adba7146a authored by Kuninori Morimoto on 28 September 2018, 02:38:36 UTC, committed by Simon Horman on 05 November 2018, 14:08:44 UTC
hscif2 has 4 dmas, but has only 2 dma-names. This patch add missing dma-names. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Fixes: e0f0bda79337701a ("arm64: dts: renesas: r8a7795: sort subnodes of the soc node") Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
1 parent 6510223
spi-xilinx.c
/*
* Xilinx SPI controller driver (master mode only)
*
* Author: MontaVista Software, Inc.
* source@mvista.com
*
* Copyright (c) 2010 Secret Lab Technologies, Ltd.
* Copyright (c) 2009 Intel Corporation
* 2002-2007 (c) MontaVista Software, Inc.
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/spi/xilinx_spi.h>
#include <linux/io.h>
#define XILINX_SPI_MAX_CS 32
#define XILINX_SPI_NAME "xilinx_spi"
/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
* Product Specification", DS464
*/
#define XSPI_CR_OFFSET 0x60 /* Control Register */
#define XSPI_CR_LOOP 0x01
#define XSPI_CR_ENABLE 0x02
#define XSPI_CR_MASTER_MODE 0x04
#define XSPI_CR_CPOL 0x08
#define XSPI_CR_CPHA 0x10
#define XSPI_CR_MODE_MASK (XSPI_CR_CPHA | XSPI_CR_CPOL | \
XSPI_CR_LSB_FIRST | XSPI_CR_LOOP)
#define XSPI_CR_TXFIFO_RESET 0x20
#define XSPI_CR_RXFIFO_RESET 0x40
#define XSPI_CR_MANUAL_SSELECT 0x80
#define XSPI_CR_TRANS_INHIBIT 0x100
#define XSPI_CR_LSB_FIRST 0x200
#define XSPI_SR_OFFSET 0x64 /* Status Register */
#define XSPI_SR_RX_EMPTY_MASK 0x01 /* Receive FIFO is empty */
#define XSPI_SR_RX_FULL_MASK 0x02 /* Receive FIFO is full */
#define XSPI_SR_TX_EMPTY_MASK 0x04 /* Transmit FIFO is empty */
#define XSPI_SR_TX_FULL_MASK 0x08 /* Transmit FIFO is full */
#define XSPI_SR_MODE_FAULT_MASK 0x10 /* Mode fault error */
#define XSPI_TXD_OFFSET 0x68 /* Data Transmit Register */
#define XSPI_RXD_OFFSET 0x6c /* Data Receive Register */
#define XSPI_SSR_OFFSET 0x70 /* 32-bit Slave Select Register */
/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
* IPIF registers are 32 bit
*/
#define XIPIF_V123B_DGIER_OFFSET 0x1c /* IPIF global int enable reg */
#define XIPIF_V123B_GINTR_ENABLE 0x80000000
#define XIPIF_V123B_IISR_OFFSET 0x20 /* IPIF interrupt status reg */
#define XIPIF_V123B_IIER_OFFSET 0x28 /* IPIF interrupt enable reg */
#define XSPI_INTR_MODE_FAULT 0x01 /* Mode fault error */
#define XSPI_INTR_SLAVE_MODE_FAULT 0x02 /* Selected as slave while
* disabled */
#define XSPI_INTR_TX_EMPTY 0x04 /* TxFIFO is empty */
#define XSPI_INTR_TX_UNDERRUN 0x08 /* TxFIFO was underrun */
#define XSPI_INTR_RX_FULL 0x10 /* RxFIFO is full */
#define XSPI_INTR_RX_OVERRUN 0x20 /* RxFIFO was overrun */
#define XSPI_INTR_TX_HALF_EMPTY 0x40 /* TxFIFO is half empty */
#define XIPIF_V123B_RESETR_OFFSET 0x40 /* IPIF reset register */
#define XIPIF_V123B_RESET_MASK 0x0a /* the value to write */
struct xilinx_spi {
/* bitbang has to be first */
struct spi_bitbang bitbang;
struct completion done;
void __iomem *regs; /* virt. address of the control registers */
int irq;
u8 *rx_ptr; /* pointer in the Tx buffer */
const u8 *tx_ptr; /* pointer in the Rx buffer */
u8 bytes_per_word;
int buffer_size; /* buffer size in words */
u32 cs_inactive; /* Level of the CS pins when inactive*/
unsigned int (*read_fn)(void __iomem *);
void (*write_fn)(u32, void __iomem *);
};
static void xspi_write32(u32 val, void __iomem *addr)
{
iowrite32(val, addr);
}
static unsigned int xspi_read32(void __iomem *addr)
{
return ioread32(addr);
}
static void xspi_write32_be(u32 val, void __iomem *addr)
{
iowrite32be(val, addr);
}
static unsigned int xspi_read32_be(void __iomem *addr)
{
return ioread32be(addr);
}
static void xilinx_spi_tx(struct xilinx_spi *xspi)
{
u32 data = 0;
if (!xspi->tx_ptr) {
xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
return;
}
switch (xspi->bytes_per_word) {
case 1:
data = *(u8 *)(xspi->tx_ptr);
break;
case 2:
data = *(u16 *)(xspi->tx_ptr);
break;
case 4:
data = *(u32 *)(xspi->tx_ptr);
break;
}
xspi->write_fn(data, xspi->regs + XSPI_TXD_OFFSET);
xspi->tx_ptr += xspi->bytes_per_word;
}
static void xilinx_spi_rx(struct xilinx_spi *xspi)
{
u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
if (!xspi->rx_ptr)
return;
switch (xspi->bytes_per_word) {
case 1:
*(u8 *)(xspi->rx_ptr) = data;
break;
case 2:
*(u16 *)(xspi->rx_ptr) = data;
break;
case 4:
*(u32 *)(xspi->rx_ptr) = data;
break;
}
xspi->rx_ptr += xspi->bytes_per_word;
}
static void xspi_init_hw(struct xilinx_spi *xspi)
{
void __iomem *regs_base = xspi->regs;
/* Reset the SPI device */
xspi->write_fn(XIPIF_V123B_RESET_MASK,
regs_base + XIPIF_V123B_RESETR_OFFSET);
/* Enable the transmit empty interrupt, which we use to determine
* progress on the transmission.
*/
xspi->write_fn(XSPI_INTR_TX_EMPTY,
regs_base + XIPIF_V123B_IIER_OFFSET);
/* Disable the global IPIF interrupt */
xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
/* Deselect the slave on the SPI bus */
xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET);
/* Disable the transmitter, enable Manual Slave Select Assertion,
* put SPI controller into master mode, and enable it */
xspi->write_fn(XSPI_CR_MANUAL_SSELECT | XSPI_CR_MASTER_MODE |
XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET | XSPI_CR_RXFIFO_RESET,
regs_base + XSPI_CR_OFFSET);
}
static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
{
struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
u16 cr;
u32 cs;
if (is_on == BITBANG_CS_INACTIVE) {
/* Deselect the slave on the SPI bus */
xspi->write_fn(xspi->cs_inactive, xspi->regs + XSPI_SSR_OFFSET);
return;
}
/* Set the SPI clock phase and polarity */
cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_MODE_MASK;
if (spi->mode & SPI_CPHA)
cr |= XSPI_CR_CPHA;
if (spi->mode & SPI_CPOL)
cr |= XSPI_CR_CPOL;
if (spi->mode & SPI_LSB_FIRST)
cr |= XSPI_CR_LSB_FIRST;
if (spi->mode & SPI_LOOP)
cr |= XSPI_CR_LOOP;
xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
/* We do not check spi->max_speed_hz here as the SPI clock
* frequency is not software programmable (the IP block design
* parameter)
*/
cs = xspi->cs_inactive;
cs ^= BIT(spi->chip_select);
/* Activate the chip select */
xspi->write_fn(cs, xspi->regs + XSPI_SSR_OFFSET);
}
/* spi_bitbang requires custom setup_transfer() to be defined if there is a
* custom txrx_bufs().
*/
static int xilinx_spi_setup_transfer(struct spi_device *spi,
struct spi_transfer *t)
{
struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
if (spi->mode & SPI_CS_HIGH)
xspi->cs_inactive &= ~BIT(spi->chip_select);
else
xspi->cs_inactive |= BIT(spi->chip_select);
return 0;
}
static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
{
struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
int remaining_words; /* the number of words left to transfer */
bool use_irq = false;
u16 cr = 0;
/* We get here with transmitter inhibited */
xspi->tx_ptr = t->tx_buf;
xspi->rx_ptr = t->rx_buf;
remaining_words = t->len / xspi->bytes_per_word;
if (xspi->irq >= 0 && remaining_words > xspi->buffer_size) {
u32 isr;
use_irq = true;
/* Inhibit irq to avoid spurious irqs on tx_empty*/
cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
xspi->regs + XSPI_CR_OFFSET);
/* ACK old irqs (if any) */
isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
if (isr)
xspi->write_fn(isr,
xspi->regs + XIPIF_V123B_IISR_OFFSET);
/* Enable the global IPIF interrupt */
xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
xspi->regs + XIPIF_V123B_DGIER_OFFSET);
reinit_completion(&xspi->done);
}
while (remaining_words) {
int n_words, tx_words, rx_words;
u32 sr;
int stalled;
n_words = min(remaining_words, xspi->buffer_size);
tx_words = n_words;
while (tx_words--)
xilinx_spi_tx(xspi);
/* Start the transfer by not inhibiting the transmitter any
* longer
*/
if (use_irq) {
xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
wait_for_completion(&xspi->done);
/* A transmit has just completed. Process received data
* and check for more data to transmit. Always inhibit
* the transmitter while the Isr refills the transmit
* register/FIFO, or make sure it is stopped if we're
* done.
*/
xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
xspi->regs + XSPI_CR_OFFSET);
sr = XSPI_SR_TX_EMPTY_MASK;
} else
sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
/* Read out all the data from the Rx FIFO */
rx_words = n_words;
stalled = 10;
while (rx_words) {
if (rx_words == n_words && !(stalled--) &&
!(sr & XSPI_SR_TX_EMPTY_MASK) &&
(sr & XSPI_SR_RX_EMPTY_MASK)) {
dev_err(&spi->dev,
"Detected stall. Check C_SPI_MODE and C_SPI_MEMORY\n");
xspi_init_hw(xspi);
return -EIO;
}
if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) {
xilinx_spi_rx(xspi);
rx_words--;
continue;
}
sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
xilinx_spi_rx(xspi);
rx_words--;
}
}
remaining_words -= n_words;
}
if (use_irq) {
xspi->write_fn(0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
}
return t->len;
}
/* This driver supports single master mode only. Hence Tx FIFO Empty
* is the only interrupt we care about.
* Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
* Fault are not to happen.
*/
static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
{
struct xilinx_spi *xspi = dev_id;
u32 ipif_isr;
/* Get the IPIF interrupts, and clear them immediately */
ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
if (ipif_isr & XSPI_INTR_TX_EMPTY) { /* Transmission completed */
complete(&xspi->done);
return IRQ_HANDLED;
}
return IRQ_NONE;
}
static int xilinx_spi_find_buffer_size(struct xilinx_spi *xspi)
{
u8 sr;
int n_words = 0;
/*
* Before the buffer_size detection we reset the core
* to make sure we start with a clean state.
*/
xspi->write_fn(XIPIF_V123B_RESET_MASK,
xspi->regs + XIPIF_V123B_RESETR_OFFSET);
/* Fill the Tx FIFO with as many words as possible */
do {
xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
n_words++;
} while (!(sr & XSPI_SR_TX_FULL_MASK));
return n_words;
}
static const struct of_device_id xilinx_spi_of_match[] = {
{ .compatible = "xlnx,axi-quad-spi-1.00.a", },
{ .compatible = "xlnx,xps-spi-2.00.a", },
{ .compatible = "xlnx,xps-spi-2.00.b", },
{}
};
MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
static int xilinx_spi_probe(struct platform_device *pdev)
{
struct xilinx_spi *xspi;
struct xspi_platform_data *pdata;
struct resource *res;
int ret, num_cs = 0, bits_per_word = 8;
struct spi_master *master;
u32 tmp;
u8 i;
pdata = dev_get_platdata(&pdev->dev);
if (pdata) {
num_cs = pdata->num_chipselect;
bits_per_word = pdata->bits_per_word;
} else {
of_property_read_u32(pdev->dev.of_node, "xlnx,num-ss-bits",
&num_cs);
}
if (!num_cs) {
dev_err(&pdev->dev,
"Missing slave select configuration data\n");
return -EINVAL;
}
if (num_cs > XILINX_SPI_MAX_CS) {
dev_err(&pdev->dev, "Invalid number of spi slaves\n");
return -EINVAL;
}
master = spi_alloc_master(&pdev->dev, sizeof(struct xilinx_spi));
if (!master)
return -ENODEV;
/* the spi->mode bits understood by this driver: */
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_LOOP |
SPI_CS_HIGH;
xspi = spi_master_get_devdata(master);
xspi->cs_inactive = 0xffffffff;
xspi->bitbang.master = master;
xspi->bitbang.chipselect = xilinx_spi_chipselect;
xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
init_completion(&xspi->done);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
xspi->regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(xspi->regs)) {
ret = PTR_ERR(xspi->regs);
goto put_master;
}
master->bus_num = pdev->id;
master->num_chipselect = num_cs;
master->dev.of_node = pdev->dev.of_node;
/*
* Detect endianess on the IP via loop bit in CR. Detection
* must be done before reset is sent because incorrect reset
* value generates error interrupt.
* Setup little endian helper functions first and try to use them
* and check if bit was correctly setup or not.
*/
xspi->read_fn = xspi_read32;
xspi->write_fn = xspi_write32;
xspi->write_fn(XSPI_CR_LOOP, xspi->regs + XSPI_CR_OFFSET);
tmp = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
tmp &= XSPI_CR_LOOP;
if (tmp != XSPI_CR_LOOP) {
xspi->read_fn = xspi_read32_be;
xspi->write_fn = xspi_write32_be;
}
master->bits_per_word_mask = SPI_BPW_MASK(bits_per_word);
xspi->bytes_per_word = bits_per_word / 8;
xspi->buffer_size = xilinx_spi_find_buffer_size(xspi);
xspi->irq = platform_get_irq(pdev, 0);
if (xspi->irq < 0 && xspi->irq != -ENXIO) {
ret = xspi->irq;
goto put_master;
} else if (xspi->irq >= 0) {
/* Register for SPI Interrupt */
ret = devm_request_irq(&pdev->dev, xspi->irq, xilinx_spi_irq, 0,
dev_name(&pdev->dev), xspi);
if (ret)
goto put_master;
}
/* SPI controller initializations */
xspi_init_hw(xspi);
ret = spi_bitbang_start(&xspi->bitbang);
if (ret) {
dev_err(&pdev->dev, "spi_bitbang_start FAILED\n");
goto put_master;
}
dev_info(&pdev->dev, "at 0x%08llX mapped to 0x%p, irq=%d\n",
(unsigned long long)res->start, xspi->regs, xspi->irq);
if (pdata) {
for (i = 0; i < pdata->num_devices; i++)
spi_new_device(master, pdata->devices + i);
}
platform_set_drvdata(pdev, master);
return 0;
put_master:
spi_master_put(master);
return ret;
}
static int xilinx_spi_remove(struct platform_device *pdev)
{
struct spi_master *master = platform_get_drvdata(pdev);
struct xilinx_spi *xspi = spi_master_get_devdata(master);
void __iomem *regs_base = xspi->regs;
spi_bitbang_stop(&xspi->bitbang);
/* Disable all the interrupts just in case */
xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET);
/* Disable the global IPIF interrupt */
xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
spi_master_put(xspi->bitbang.master);
return 0;
}
/* work with hotplug and coldplug */
MODULE_ALIAS("platform:" XILINX_SPI_NAME);
static struct platform_driver xilinx_spi_driver = {
.probe = xilinx_spi_probe,
.remove = xilinx_spi_remove,
.driver = {
.name = XILINX_SPI_NAME,
.of_match_table = xilinx_spi_of_match,
},
};
module_platform_driver(xilinx_spi_driver);
MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
MODULE_DESCRIPTION("Xilinx SPI driver");
MODULE_LICENSE("GPL");
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...