Revision ae9955aeb8e47c4f60a02add47acf9850ca0ead7 authored by Alexey Brodkin on 23 March 2017, 17:34:45 UTC, committed by Vineet Gupta on 24 March 2017, 20:36:08 UTC
MotherBoard section has its "ranges" set to 0xE000_0000-0xF000_0000. But UIO node maps 4 different areas in different memory locations and all outside MB's ranges. That obviously breaks UIO mappings in runtime. Cc: Ruud Derwig <rderwig@synopsys.com> Cc: stable@vger.kernel.org Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
1 parent 814a585
Kconfig
config MMU
def_bool y
config ZONE_DMA
def_bool y
config CPU_BIG_ENDIAN
def_bool y
config LOCKDEP_SUPPORT
def_bool y
config STACKTRACE_SUPPORT
def_bool y
config RWSEM_GENERIC_SPINLOCK
bool
config RWSEM_XCHGADD_ALGORITHM
def_bool y
config ARCH_HAS_ILOG2_U32
def_bool n
config ARCH_HAS_ILOG2_U64
def_bool n
config GENERIC_HWEIGHT
def_bool y
config GENERIC_BUG
def_bool y if BUG
config GENERIC_BUG_RELATIVE_POINTERS
def_bool y
config ARCH_DMA_ADDR_T_64BIT
def_bool y
config GENERIC_LOCKBREAK
def_bool y if SMP && PREEMPT
config PGSTE
def_bool y if KVM
config ARCH_SUPPORTS_DEBUG_PAGEALLOC
def_bool y
config KEXEC
def_bool y
select KEXEC_CORE
config AUDIT_ARCH
def_bool y
config NO_IOPORT_MAP
def_bool y
config PCI_QUIRKS
def_bool n
config ARCH_SUPPORTS_UPROBES
def_bool y
config S390
def_bool y
select ARCH_HAS_DEVMEM_IS_ALLOWED
select ARCH_HAS_ELF_RANDOMIZE
select ARCH_HAS_GCOV_PROFILE_ALL
select ARCH_HAS_GIGANTIC_PAGE
select ARCH_HAS_KCOV
select ARCH_HAS_SET_MEMORY
select ARCH_HAS_SG_CHAIN
select ARCH_HAS_STRICT_KERNEL_RWX
select ARCH_HAS_STRICT_MODULE_RWX
select ARCH_HAS_UBSAN_SANITIZE_ALL
select ARCH_HAVE_NMI_SAFE_CMPXCHG
select ARCH_INLINE_READ_LOCK
select ARCH_INLINE_READ_LOCK_BH
select ARCH_INLINE_READ_LOCK_IRQ
select ARCH_INLINE_READ_LOCK_IRQSAVE
select ARCH_INLINE_READ_TRYLOCK
select ARCH_INLINE_READ_UNLOCK
select ARCH_INLINE_READ_UNLOCK_BH
select ARCH_INLINE_READ_UNLOCK_IRQ
select ARCH_INLINE_READ_UNLOCK_IRQRESTORE
select ARCH_INLINE_SPIN_LOCK
select ARCH_INLINE_SPIN_LOCK_BH
select ARCH_INLINE_SPIN_LOCK_IRQ
select ARCH_INLINE_SPIN_LOCK_IRQSAVE
select ARCH_INLINE_SPIN_TRYLOCK
select ARCH_INLINE_SPIN_TRYLOCK_BH
select ARCH_INLINE_SPIN_UNLOCK
select ARCH_INLINE_SPIN_UNLOCK_BH
select ARCH_INLINE_SPIN_UNLOCK_IRQ
select ARCH_INLINE_SPIN_UNLOCK_IRQRESTORE
select ARCH_INLINE_WRITE_LOCK
select ARCH_INLINE_WRITE_LOCK_BH
select ARCH_INLINE_WRITE_LOCK_IRQ
select ARCH_INLINE_WRITE_LOCK_IRQSAVE
select ARCH_INLINE_WRITE_TRYLOCK
select ARCH_INLINE_WRITE_UNLOCK
select ARCH_INLINE_WRITE_UNLOCK_BH
select ARCH_INLINE_WRITE_UNLOCK_IRQ
select ARCH_INLINE_WRITE_UNLOCK_IRQRESTORE
select ARCH_SAVE_PAGE_KEYS if HIBERNATION
select ARCH_SUPPORTS_ATOMIC_RMW
select ARCH_SUPPORTS_NUMA_BALANCING
select ARCH_USE_BUILTIN_BSWAP
select ARCH_USE_CMPXCHG_LOCKREF
select ARCH_WANTS_DYNAMIC_TASK_STRUCT
select ARCH_WANTS_PROT_NUMA_PROT_NONE
select ARCH_WANTS_UBSAN_NO_NULL
select ARCH_WANT_IPC_PARSE_VERSION
select BUILDTIME_EXTABLE_SORT
select CLONE_BACKWARDS2
select DYNAMIC_FTRACE if FUNCTION_TRACER
select GENERIC_CLOCKEVENTS
select GENERIC_CPU_AUTOPROBE
select GENERIC_CPU_DEVICES if !SMP
select GENERIC_FIND_FIRST_BIT
select GENERIC_SMP_IDLE_THREAD
select GENERIC_TIME_VSYSCALL
select HAVE_ALIGNED_STRUCT_PAGE if SLUB
select HAVE_ARCH_AUDITSYSCALL
select HAVE_ARCH_EARLY_PFN_TO_NID
select HAVE_ARCH_HARDENED_USERCOPY
select HAVE_ARCH_JUMP_LABEL
select CPU_NO_EFFICIENT_FFS if !HAVE_MARCH_Z9_109_FEATURES
select HAVE_ARCH_SECCOMP_FILTER
select HAVE_ARCH_SOFT_DIRTY
select HAVE_ARCH_TRACEHOOK
select HAVE_ARCH_TRANSPARENT_HUGEPAGE
select HAVE_EBPF_JIT if PACK_STACK && HAVE_MARCH_Z196_FEATURES
select HAVE_CMPXCHG_DOUBLE
select HAVE_CMPXCHG_LOCAL
select HAVE_COPY_THREAD_TLS
select HAVE_DEBUG_KMEMLEAK
select HAVE_DMA_API_DEBUG
select HAVE_DMA_CONTIGUOUS
select DMA_NOOP_OPS
select HAVE_DYNAMIC_FTRACE
select HAVE_DYNAMIC_FTRACE_WITH_REGS
select HAVE_EFFICIENT_UNALIGNED_ACCESS
select HAVE_EXIT_THREAD
select HAVE_FTRACE_MCOUNT_RECORD
select HAVE_FUNCTION_GRAPH_TRACER
select HAVE_FUNCTION_TRACER
select HAVE_FUTEX_CMPXCHG if FUTEX
select HAVE_KERNEL_BZIP2
select HAVE_KERNEL_GZIP
select HAVE_KERNEL_LZ4
select HAVE_KERNEL_LZMA
select HAVE_KERNEL_LZO
select HAVE_KERNEL_XZ
select HAVE_KPROBES
select HAVE_KRETPROBES
select HAVE_KVM
select HAVE_LIVEPATCH
select HAVE_MEMBLOCK
select HAVE_MEMBLOCK_NODE_MAP
select HAVE_MEMBLOCK_PHYS_MAP
select HAVE_MOD_ARCH_SPECIFIC
select HAVE_OPROFILE
select HAVE_PERF_EVENTS
select HAVE_REGS_AND_STACK_ACCESS_API
select HAVE_SYSCALL_TRACEPOINTS
select HAVE_VIRT_CPU_ACCOUNTING
select MODULES_USE_ELF_RELA
select NO_BOOTMEM
select OLD_SIGACTION
select OLD_SIGSUSPEND3
select SPARSE_IRQ
select SYSCTL_EXCEPTION_TRACE
select THREAD_INFO_IN_TASK
select TTY
select VIRT_CPU_ACCOUNTING
select ARCH_HAS_SCALED_CPUTIME
select VIRT_TO_BUS
select HAVE_NMI
config SCHED_OMIT_FRAME_POINTER
def_bool y
config PGTABLE_LEVELS
int
default 4
source "init/Kconfig"
source "kernel/Kconfig.freezer"
source "kernel/livepatch/Kconfig"
menu "Processor type and features"
config HAVE_MARCH_Z900_FEATURES
def_bool n
config HAVE_MARCH_Z990_FEATURES
def_bool n
select HAVE_MARCH_Z900_FEATURES
config HAVE_MARCH_Z9_109_FEATURES
def_bool n
select HAVE_MARCH_Z990_FEATURES
config HAVE_MARCH_Z10_FEATURES
def_bool n
select HAVE_MARCH_Z9_109_FEATURES
config HAVE_MARCH_Z196_FEATURES
def_bool n
select HAVE_MARCH_Z10_FEATURES
config HAVE_MARCH_ZEC12_FEATURES
def_bool n
select HAVE_MARCH_Z196_FEATURES
config HAVE_MARCH_Z13_FEATURES
def_bool n
select HAVE_MARCH_ZEC12_FEATURES
choice
prompt "Processor type"
default MARCH_Z196
config MARCH_Z900
bool "IBM zSeries model z800 and z900"
select HAVE_MARCH_Z900_FEATURES
help
Select this to enable optimizations for model z800/z900 (2064 and
2066 series). This will enable some optimizations that are not
available on older ESA/390 (31 Bit) only CPUs.
config MARCH_Z990
bool "IBM zSeries model z890 and z990"
select HAVE_MARCH_Z990_FEATURES
help
Select this to enable optimizations for model z890/z990 (2084 and
2086 series). The kernel will be slightly faster but will not work
on older machines.
config MARCH_Z9_109
bool "IBM System z9"
select HAVE_MARCH_Z9_109_FEATURES
help
Select this to enable optimizations for IBM System z9 (2094 and
2096 series). The kernel will be slightly faster but will not work
on older machines.
config MARCH_Z10
bool "IBM System z10"
select HAVE_MARCH_Z10_FEATURES
help
Select this to enable optimizations for IBM System z10 (2097 and
2098 series). The kernel will be slightly faster but will not work
on older machines.
config MARCH_Z196
bool "IBM zEnterprise 114 and 196"
select HAVE_MARCH_Z196_FEATURES
help
Select this to enable optimizations for IBM zEnterprise 114 and 196
(2818 and 2817 series). The kernel will be slightly faster but will
not work on older machines.
config MARCH_ZEC12
bool "IBM zBC12 and zEC12"
select HAVE_MARCH_ZEC12_FEATURES
help
Select this to enable optimizations for IBM zBC12 and zEC12 (2828 and
2827 series). The kernel will be slightly faster but will not work on
older machines.
config MARCH_Z13
bool "IBM z13s and z13"
select HAVE_MARCH_Z13_FEATURES
help
Select this to enable optimizations for IBM z13s and z13 (2965 and
2964 series). The kernel will be slightly faster but will not work on
older machines.
endchoice
config MARCH_Z900_TUNE
def_bool TUNE_Z900 || MARCH_Z900 && TUNE_DEFAULT
config MARCH_Z990_TUNE
def_bool TUNE_Z990 || MARCH_Z990 && TUNE_DEFAULT
config MARCH_Z9_109_TUNE
def_bool TUNE_Z9_109 || MARCH_Z9_109 && TUNE_DEFAULT
config MARCH_Z10_TUNE
def_bool TUNE_Z10 || MARCH_Z10 && TUNE_DEFAULT
config MARCH_Z196_TUNE
def_bool TUNE_Z196 || MARCH_Z196 && TUNE_DEFAULT
config MARCH_ZEC12_TUNE
def_bool TUNE_ZEC12 || MARCH_ZEC12 && TUNE_DEFAULT
config MARCH_Z13_TUNE
def_bool TUNE_Z13 || MARCH_Z13 && TUNE_DEFAULT
choice
prompt "Tune code generation"
default TUNE_DEFAULT
help
Cause the compiler to tune (-mtune) the generated code for a machine.
This will make the code run faster on the selected machine but
somewhat slower on other machines.
This option only changes how the compiler emits instructions, not the
selection of instructions itself, so the resulting kernel will run on
all other machines.
config TUNE_DEFAULT
bool "Default"
help
Tune the generated code for the target processor for which the kernel
will be compiled.
config TUNE_Z900
bool "IBM zSeries model z800 and z900"
config TUNE_Z990
bool "IBM zSeries model z890 and z990"
config TUNE_Z9_109
bool "IBM System z9"
config TUNE_Z10
bool "IBM System z10"
config TUNE_Z196
bool "IBM zEnterprise 114 and 196"
config TUNE_ZEC12
bool "IBM zBC12 and zEC12"
config TUNE_Z13
bool "IBM z13"
endchoice
config 64BIT
def_bool y
config COMPAT
def_bool y
prompt "Kernel support for 31 bit emulation"
select COMPAT_BINFMT_ELF if BINFMT_ELF
select ARCH_WANT_OLD_COMPAT_IPC
select COMPAT_OLD_SIGACTION
depends on MULTIUSER
help
Select this option if you want to enable your system kernel to
handle system-calls from ELF binaries for 31 bit ESA. This option
(and some other stuff like libraries and such) is needed for
executing 31 bit applications. It is safe to say "Y".
config SYSVIPC_COMPAT
def_bool y if COMPAT && SYSVIPC
config KEYS_COMPAT
def_bool y if COMPAT && KEYS
config SMP
def_bool y
prompt "Symmetric multi-processing support"
---help---
This enables support for systems with more than one CPU. If you have
a system with only one CPU, like most personal computers, say N. If
you have a system with more than one CPU, say Y.
If you say N here, the kernel will run on uni- and multiprocessor
machines, but will use only one CPU of a multiprocessor machine. If
you say Y here, the kernel will run on many, but not all,
uniprocessor machines. On a uniprocessor machine, the kernel
will run faster if you say N here.
See also the SMP-HOWTO available at
<http://www.tldp.org/docs.html#howto>.
Even if you don't know what to do here, say Y.
config NR_CPUS
int "Maximum number of CPUs (2-512)"
range 2 512
depends on SMP
default "64"
help
This allows you to specify the maximum number of CPUs which this
kernel will support. The maximum supported value is 512 and the
minimum value which makes sense is 2.
This is purely to save memory - each supported CPU adds
approximately sixteen kilobytes to the kernel image.
config HOTPLUG_CPU
def_bool y
prompt "Support for hot-pluggable CPUs"
depends on SMP
help
Say Y here to be able to turn CPUs off and on. CPUs
can be controlled through /sys/devices/system/cpu/cpu#.
Say N if you want to disable CPU hotplug.
# Some NUMA nodes have memory ranges that span
# other nodes. Even though a pfn is valid and
# between a node's start and end pfns, it may not
# reside on that node. See memmap_init_zone()
# for details. <- They meant memory holes!
config NODES_SPAN_OTHER_NODES
def_bool NUMA
config NUMA
bool "NUMA support"
depends on SMP && SCHED_TOPOLOGY
default n
help
Enable NUMA support
This option adds NUMA support to the kernel.
An operation mode can be selected by appending
numa=<method> to the kernel command line.
The default behaviour is identical to appending numa=plain to
the command line. This will create just one node with all
available memory and all CPUs in it.
config NODES_SHIFT
int "Maximum NUMA nodes (as a power of 2)"
range 1 10
depends on NUMA
default "4"
help
Specify the maximum number of NUMA nodes available on the target
system. Increases memory reserved to accommodate various tables.
menu "Select NUMA modes"
depends on NUMA
config NUMA_EMU
bool "NUMA emulation"
default y
help
Numa emulation mode will split the available system memory into
equal chunks which then are distributed over the configured number
of nodes in a round-robin manner.
The number of fake nodes is limited by the number of available memory
chunks (i.e. memory size / fake size) and the number of supported
nodes in the kernel.
The CPUs are assigned to the nodes in a way that partially respects
the original machine topology (if supported by the machine).
Fair distribution of the CPUs is not guaranteed.
config EMU_SIZE
hex "NUMA emulation memory chunk size"
default 0x10000000
range 0x400000 0x100000000
depends on NUMA_EMU
help
Select the default size by which the memory is chopped and then
assigned to emulated NUMA nodes.
This can be overridden by specifying
emu_size=<n>
on the kernel command line where also suffixes K, M, G, and T are
supported.
endmenu
config SCHED_SMT
def_bool n
config SCHED_MC
def_bool n
config SCHED_BOOK
def_bool n
config SCHED_DRAWER
def_bool n
config SCHED_TOPOLOGY
def_bool y
prompt "Topology scheduler support"
depends on SMP
select SCHED_SMT
select SCHED_MC
select SCHED_BOOK
select SCHED_DRAWER
help
Topology scheduler support improves the CPU scheduler's decision
making when dealing with machines that have multi-threading,
multiple cores or multiple books.
source kernel/Kconfig.preempt
source kernel/Kconfig.hz
endmenu
menu "Memory setup"
config ARCH_SPARSEMEM_ENABLE
def_bool y
select SPARSEMEM_VMEMMAP_ENABLE
select SPARSEMEM_VMEMMAP
config ARCH_SPARSEMEM_DEFAULT
def_bool y
config ARCH_SELECT_MEMORY_MODEL
def_bool y
config ARCH_ENABLE_MEMORY_HOTPLUG
def_bool y if SPARSEMEM
config ARCH_ENABLE_MEMORY_HOTREMOVE
def_bool y
config ARCH_ENABLE_SPLIT_PMD_PTLOCK
def_bool y
config FORCE_MAX_ZONEORDER
int
default "9"
source "mm/Kconfig"
config PACK_STACK
def_bool y
prompt "Pack kernel stack"
help
This option enables the compiler option -mkernel-backchain if it
is available. If the option is available the compiler supports
the new stack layout which dramatically reduces the minimum stack
frame size. With an old compiler a non-leaf function needs a
minimum of 96 bytes on 31 bit and 160 bytes on 64 bit. With
-mkernel-backchain the minimum size drops to 16 byte on 31 bit
and 24 byte on 64 bit.
Say Y if you are unsure.
config CHECK_STACK
def_bool y
prompt "Detect kernel stack overflow"
help
This option enables the compiler option -mstack-guard and
-mstack-size if they are available. If the compiler supports them
it will emit additional code to each function prolog to trigger
an illegal operation if the kernel stack is about to overflow.
Say N if you are unsure.
config STACK_GUARD
int "Size of the guard area (128-1024)"
range 128 1024
depends on CHECK_STACK
default "256"
help
This allows you to specify the size of the guard area at the lower
end of the kernel stack. If the kernel stack points into the guard
area on function entry an illegal operation is triggered. The size
needs to be a power of 2. Please keep in mind that the size of an
interrupt frame is 184 bytes for 31 bit and 328 bytes on 64 bit.
The minimum size for the stack guard should be 256 for 31 bit and
512 for 64 bit.
config WARN_DYNAMIC_STACK
def_bool n
prompt "Emit compiler warnings for function with dynamic stack usage"
help
This option enables the compiler option -mwarn-dynamicstack. If the
compiler supports this options generates warnings for functions
that dynamically allocate stack space using alloca.
Say N if you are unsure.
endmenu
menu "I/O subsystem"
config QDIO
def_tristate y
prompt "QDIO support"
---help---
This driver provides the Queued Direct I/O base support for
IBM System z.
To compile this driver as a module, choose M here: the
module will be called qdio.
If unsure, say Y.
menuconfig PCI
bool "PCI support"
select PCI_MSI
select IOMMU_SUPPORT
help
Enable PCI support.
if PCI
config PCI_NR_FUNCTIONS
int "Maximum number of PCI functions (1-4096)"
range 1 4096
default "64"
help
This allows you to specify the maximum number of PCI functions which
this kernel will support.
source "drivers/pci/Kconfig"
endif # PCI
config PCI_DOMAINS
def_bool PCI
config HAS_IOMEM
def_bool PCI
config IOMMU_HELPER
def_bool PCI
config NEED_SG_DMA_LENGTH
def_bool PCI
config NEED_DMA_MAP_STATE
def_bool PCI
config CHSC_SCH
def_tristate m
prompt "Support for CHSC subchannels"
help
This driver allows usage of CHSC subchannels. A CHSC subchannel
is usually present on LPAR only.
The driver creates a device /dev/chsc, which may be used to
obtain I/O configuration information about the machine and
to issue asynchronous chsc commands (DANGEROUS).
You will usually only want to use this interface on a special
LPAR designated for system management.
To compile this driver as a module, choose M here: the
module will be called chsc_sch.
If unsure, say N.
config SCM_BUS
def_bool y
prompt "SCM bus driver"
help
Bus driver for Storage Class Memory.
config EADM_SCH
def_tristate m
prompt "Support for EADM subchannels"
depends on SCM_BUS
help
This driver allows usage of EADM subchannels. EADM subchannels act
as a communication vehicle for SCM increments.
To compile this driver as a module, choose M here: the
module will be called eadm_sch.
endmenu
menu "Dump support"
config CRASH_DUMP
bool "kernel crash dumps"
depends on SMP
select KEXEC
help
Generate crash dump after being started by kexec.
Crash dump kernels are loaded in the main kernel with kexec-tools
into a specially reserved region and then later executed after
a crash by kdump/kexec.
Refer to <file:Documentation/s390/zfcpdump.txt> for more details on this.
This option also enables s390 zfcpdump.
See also <file:Documentation/s390/zfcpdump.txt>
endmenu
menu "Executable file formats / Emulations"
source "fs/Kconfig.binfmt"
config SECCOMP
def_bool y
prompt "Enable seccomp to safely compute untrusted bytecode"
depends on PROC_FS
help
This kernel feature is useful for number crunching applications
that may need to compute untrusted bytecode during their
execution. By using pipes or other transports made available to
the process as file descriptors supporting the read/write
syscalls, it's possible to isolate those applications in
their own address space using seccomp. Once seccomp is
enabled via /proc/<pid>/seccomp, it cannot be disabled
and the task is only allowed to execute a few safe syscalls
defined by each seccomp mode.
If unsure, say Y.
endmenu
menu "Power Management"
config ARCH_HIBERNATION_POSSIBLE
def_bool y
source "kernel/power/Kconfig"
endmenu
source "net/Kconfig"
config PCMCIA
def_bool n
config CCW
def_bool y
source "drivers/Kconfig"
source "fs/Kconfig"
source "arch/s390/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"
menu "Virtualization"
config PFAULT
def_bool y
prompt "Pseudo page fault support"
help
Select this option, if you want to use PFAULT pseudo page fault
handling under VM. If running native or in LPAR, this option
has no effect. If your VM does not support PFAULT, PAGEEX
pseudo page fault handling will be used.
Note that VM 4.2 supports PFAULT but has a bug in its
implementation that causes some problems.
Everybody who wants to run Linux under VM != VM4.2 should select
this option.
config SHARED_KERNEL
bool "VM shared kernel support"
depends on !JUMP_LABEL
help
Select this option, if you want to share the text segment of the
Linux kernel between different VM guests. This reduces memory
usage with lots of guests but greatly increases kernel size.
Also if a kernel was IPL'ed from a shared segment the kexec system
call will not work.
You should only select this option if you know what you are
doing and want to exploit this feature.
config CMM
def_tristate n
prompt "Cooperative memory management"
help
Select this option, if you want to enable the kernel interface
to reduce the memory size of the system. This is accomplished
by allocating pages of memory and put them "on hold". This only
makes sense for a system running under VM where the unused pages
will be reused by VM for other guest systems. The interface
allows an external monitor to balance memory of many systems.
Everybody who wants to run Linux under VM should select this
option.
config CMM_IUCV
def_bool y
prompt "IUCV special message interface to cooperative memory management"
depends on CMM && (SMSGIUCV=y || CMM=SMSGIUCV)
help
Select this option to enable the special message interface to
the cooperative memory management.
config APPLDATA_BASE
def_bool n
prompt "Linux - VM Monitor Stream, base infrastructure"
depends on PROC_FS
help
This provides a kernel interface for creating and updating z/VM APPLDATA
monitor records. The monitor records are updated at certain time
intervals, once the timer is started.
Writing 1 or 0 to /proc/appldata/timer starts(1) or stops(0) the timer,
i.e. enables or disables monitoring on the Linux side.
A custom interval value (in seconds) can be written to
/proc/appldata/interval.
Defaults are 60 seconds interval and timer off.
The /proc entries can also be read from, showing the current settings.
config APPLDATA_MEM
def_tristate m
prompt "Monitor memory management statistics"
depends on APPLDATA_BASE && VM_EVENT_COUNTERS
help
This provides memory management related data to the Linux - VM Monitor
Stream, like paging/swapping rate, memory utilisation, etc.
Writing 1 or 0 to /proc/appldata/memory creates(1) or removes(0) a z/VM
APPLDATA monitor record, i.e. enables or disables monitoring this record
on the z/VM side.
Default is disabled.
The /proc entry can also be read from, showing the current settings.
This can also be compiled as a module, which will be called
appldata_mem.o.
config APPLDATA_OS
def_tristate m
prompt "Monitor OS statistics"
depends on APPLDATA_BASE
help
This provides OS related data to the Linux - VM Monitor Stream, like
CPU utilisation, etc.
Writing 1 or 0 to /proc/appldata/os creates(1) or removes(0) a z/VM
APPLDATA monitor record, i.e. enables or disables monitoring this record
on the z/VM side.
Default is disabled.
This can also be compiled as a module, which will be called
appldata_os.o.
config APPLDATA_NET_SUM
def_tristate m
prompt "Monitor overall network statistics"
depends on APPLDATA_BASE && NET
help
This provides network related data to the Linux - VM Monitor Stream,
currently there is only a total sum of network I/O statistics, no
per-interface data.
Writing 1 or 0 to /proc/appldata/net_sum creates(1) or removes(0) a z/VM
APPLDATA monitor record, i.e. enables or disables monitoring this record
on the z/VM side.
Default is disabled.
This can also be compiled as a module, which will be called
appldata_net_sum.o.
config S390_HYPFS_FS
def_bool y
prompt "s390 hypervisor file system support"
select SYS_HYPERVISOR
help
This is a virtual file system intended to provide accounting
information in an s390 hypervisor environment.
source "arch/s390/kvm/Kconfig"
config S390_GUEST
def_bool y
prompt "s390 support for virtio devices"
select TTY
select VIRTUALIZATION
select VIRTIO
select VIRTIO_CONSOLE
help
Enabling this option adds support for virtio based paravirtual device
drivers on s390.
Select this option if you want to run the kernel as a guest under
the KVM hypervisor.
config S390_GUEST_OLD_TRANSPORT
def_bool y
prompt "Guest support for old s390 virtio transport (DEPRECATED)"
depends on S390_GUEST
help
Enable this option to add support for the old s390-virtio
transport (i.e. virtio devices NOT based on virtio-ccw). This
type of virtio devices is only available on the experimental
kuli userspace or with old (< 2.6) qemu. If you are running
with a modern version of qemu (which supports virtio-ccw since
1.4 and uses it by default since version 2.4), you probably won't
need this.
endmenu
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...