https://github.com/torvalds/linux
Revision aef2b89662b8a7506846d0dc0df672d196ddf8d0 authored by Russ Dill on 09 May 2012, 22:15:03 UTC, committed by Tony Lindgren on 20 June 2012, 14:18:21 UTC
Commit e813a55eb9c9bc6c8039fb16332cf43402125b30 ("OMAP: board-files: remove custom PD GPIO handling for DVI output") moved TFP410 chip's powerdown-gpio handling from the board files to the tfp410 driver. One gpio_request_one(powerdown-gpio, ...) was mistakenly left unremoved in the Beagle board file. This causes the tfp410 driver to fail to request the gpio on Beagle, causing the driver to fail and thus the DVI output doesn't work. This patch removes several boot errors from board-omap3beagle.c: - gpio_request: gpio--22 (DVI reset) status -22 - Unable to get DVI reset GPIO There is a combination of leftover code and revision confusion. Additionally, xM support is currently a hack. For original Beagleboard this removes the double initialization of GPIO 170, properly configures it as an output, and wraps the initialization in an if block so that xM does not attempt to request it. For Beagleboard xM it removes reference to GPIO 129 which was part of rev A1 and A2 designs, but never functioned. It then properly assigns beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the hack of initializing it high. Additionally, it uses gpio_set_value_cansleep since this GPIO is connected through i2c. Unfortunately, there is no way to tell the difference between xM A2 and A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL GPIO used on A3 and beyond is not used on rev A1 and A2, there are no problems created by this fix. Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4. Signed-off-by: Russ Dill <Russ.Dill@ti.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
1 parent 95dca12
Tip revision: aef2b89662b8a7506846d0dc0df672d196ddf8d0 authored by Russ Dill on 09 May 2012, 22:15:03 UTC
ARM: OMAP: Fix Beagleboard DVI reset gpio
ARM: OMAP: Fix Beagleboard DVI reset gpio
Tip revision: aef2b89
Kbuild
#
# Kbuild for top-level directory of the kernel
# This file takes care of the following:
# 1) Generate bounds.h
# 2) Generate asm-offsets.h (may need bounds.h)
# 3) Check for missing system calls
#####
# 1) Generate bounds.h
bounds-file := include/generated/bounds.h
always := $(bounds-file)
targets := $(bounds-file) kernel/bounds.s
quiet_cmd_bounds = GEN $@
define cmd_bounds
(set -e; \
echo "#ifndef __LINUX_BOUNDS_H__"; \
echo "#define __LINUX_BOUNDS_H__"; \
echo "/*"; \
echo " * DO NOT MODIFY."; \
echo " *"; \
echo " * This file was generated by Kbuild"; \
echo " *"; \
echo " */"; \
echo ""; \
sed -ne $(sed-y) $<; \
echo ""; \
echo "#endif" ) > $@
endef
# We use internal kbuild rules to avoid the "is up to date" message from make
kernel/bounds.s: kernel/bounds.c FORCE
$(Q)mkdir -p $(dir $@)
$(call if_changed_dep,cc_s_c)
$(obj)/$(bounds-file): kernel/bounds.s Kbuild
$(Q)mkdir -p $(dir $@)
$(call cmd,bounds)
#####
# 2) Generate asm-offsets.h
#
offsets-file := include/generated/asm-offsets.h
always += $(offsets-file)
targets += $(offsets-file)
targets += arch/$(SRCARCH)/kernel/asm-offsets.s
# Default sed regexp - multiline due to syntax constraints
define sed-y
"/^->/{s:->#\(.*\):/* \1 */:; \
s:^->\([^ ]*\) [\$$#]*\([-0-9]*\) \(.*\):#define \1 \2 /* \3 */:; \
s:^->\([^ ]*\) [\$$#]*\([^ ]*\) \(.*\):#define \1 \2 /* \3 */:; \
s:->::; p;}"
endef
quiet_cmd_offsets = GEN $@
define cmd_offsets
(set -e; \
echo "#ifndef __ASM_OFFSETS_H__"; \
echo "#define __ASM_OFFSETS_H__"; \
echo "/*"; \
echo " * DO NOT MODIFY."; \
echo " *"; \
echo " * This file was generated by Kbuild"; \
echo " *"; \
echo " */"; \
echo ""; \
sed -ne $(sed-y) $<; \
echo ""; \
echo "#endif" ) > $@
endef
# We use internal kbuild rules to avoid the "is up to date" message from make
arch/$(SRCARCH)/kernel/asm-offsets.s: arch/$(SRCARCH)/kernel/asm-offsets.c \
$(obj)/$(bounds-file) FORCE
$(Q)mkdir -p $(dir $@)
$(call if_changed_dep,cc_s_c)
$(obj)/$(offsets-file): arch/$(SRCARCH)/kernel/asm-offsets.s Kbuild
$(call cmd,offsets)
#####
# 3) Check for missing system calls
#
always += missing-syscalls
targets += missing-syscalls
quiet_cmd_syscalls = CALL $<
cmd_syscalls = $(CONFIG_SHELL) $< $(CC) $(c_flags) $(missing_syscalls_flags)
missing-syscalls: scripts/checksyscalls.sh $(offsets-file) FORCE
$(call cmd,syscalls)
# Keep these two files during make clean
no-clean-files := $(bounds-file) $(offsets-file)
Computing file changes ...