Revision b3fc9c6c58c986f7a24fd8b0794d1e0794935a28 authored by Johannes Berg on 13 April 2008, 08:12:47 UTC, committed by John W. Linville on 15 April 2008, 19:04:36 UTC
Some people are getting this message a lot, and we have traced it to broken access points that much too often send completely empty frames (all bytes zeroed, which they shouldn't do at all.) Since we cannot do anything about such frames in any case except the special case where we're debugging an AP, just remove the message. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
1 parent 2dd0f69
Makefile
#
# Makefile for the Linux kernel device drivers.
#
# 15 Sep 2000, Christoph Hellwig <hch@infradead.org>
# Rewritten to use lists instead of if-statements.
#
obj-$(CONFIG_HAVE_GPIO_LIB) += gpio/
obj-$(CONFIG_PCI) += pci/
obj-$(CONFIG_PARISC) += parisc/
obj-$(CONFIG_RAPIDIO) += rapidio/
obj-y += video/
obj-$(CONFIG_ACPI) += acpi/
# PnP must come after ACPI since it will eventually need to check if acpi
# was used and do nothing if so
obj-$(CONFIG_PNP) += pnp/
obj-$(CONFIG_ARM_AMBA) += amba/
obj-$(CONFIG_XEN) += xen/
# char/ comes before serial/ etc so that the VT console is the boot-time
# default.
obj-y += char/
obj-$(CONFIG_CONNECTOR) += connector/
# i810fb and intelfb depend on char/agp/
obj-$(CONFIG_FB_I810) += video/i810/
obj-$(CONFIG_FB_INTEL) += video/intelfb/
obj-y += serial/
obj-$(CONFIG_PARPORT) += parport/
obj-y += base/ block/ misc/ mfd/ net/ media/
obj-$(CONFIG_NUBUS) += nubus/
obj-$(CONFIG_ATM) += atm/
obj-y += macintosh/
obj-$(CONFIG_IDE) += ide/
obj-$(CONFIG_SCSI) += scsi/
obj-$(CONFIG_ATA) += ata/
obj-$(CONFIG_FUSION) += message/
obj-$(CONFIG_FIREWIRE) += firewire/
obj-y += ieee1394/
obj-$(CONFIG_UIO) += uio/
obj-y += cdrom/
obj-y += auxdisplay/
obj-$(CONFIG_MTD) += mtd/
obj-$(CONFIG_SPI) += spi/
obj-$(CONFIG_PCCARD) += pcmcia/
obj-$(CONFIG_DIO) += dio/
obj-$(CONFIG_SBUS) += sbus/
obj-$(CONFIG_ZORRO) += zorro/
obj-$(CONFIG_MAC) += macintosh/
obj-$(CONFIG_ATA_OVER_ETH) += block/aoe/
obj-$(CONFIG_PARIDE) += block/paride/
obj-$(CONFIG_TC) += tc/
obj-$(CONFIG_USB) += usb/
obj-$(CONFIG_PCI) += usb/
obj-$(CONFIG_USB_GADGET) += usb/gadget/
obj-$(CONFIG_SERIO) += input/serio/
obj-$(CONFIG_GAMEPORT) += input/gameport/
obj-$(CONFIG_INPUT) += input/
obj-$(CONFIG_I2O) += message/
obj-$(CONFIG_RTC_LIB) += rtc/
obj-y += i2c/
obj-$(CONFIG_W1) += w1/
obj-$(CONFIG_POWER_SUPPLY) += power/
obj-$(CONFIG_HWMON) += hwmon/
obj-$(CONFIG_THERMAL) += thermal/
obj-$(CONFIG_WATCHDOG) += watchdog/
obj-$(CONFIG_PHONE) += telephony/
obj-$(CONFIG_MD) += md/
obj-$(CONFIG_BT) += bluetooth/
obj-$(CONFIG_ISDN) += isdn/
obj-$(CONFIG_EDAC) += edac/
obj-$(CONFIG_MCA) += mca/
obj-$(CONFIG_EISA) += eisa/
obj-y += lguest/
obj-$(CONFIG_CPU_FREQ) += cpufreq/
obj-$(CONFIG_CPU_IDLE) += cpuidle/
obj-$(CONFIG_MMC) += mmc/
obj-$(CONFIG_MEMSTICK) += memstick/
obj-$(CONFIG_NEW_LEDS) += leds/
obj-$(CONFIG_INFINIBAND) += infiniband/
obj-$(CONFIG_SGI_SN) += sn/
obj-y += firmware/
obj-$(CONFIG_CRYPTO) += crypto/
obj-$(CONFIG_SUPERH) += sh/
obj-$(CONFIG_GENERIC_TIME) += clocksource/
obj-$(CONFIG_DMA_ENGINE) += dma/
obj-$(CONFIG_DCA) += dca/
obj-$(CONFIG_HID) += hid/
obj-$(CONFIG_PPC_PS3) += ps3/
obj-$(CONFIG_OF) += of/
obj-$(CONFIG_SSB) += ssb/
obj-$(CONFIG_VIRTIO) += virtio/
Computing file changes ...
