Revision b794e252f5c1c640097348566dd85d463698ce90 authored by David S. Miller on 20 December 2016, 19:15:45 UTC, committed by David S. Miller on 20 December 2016, 19:15:45 UTC
Xin Long says: ==================== sctp: fix the issue that may copy duplicate addrs into assoc's bind address list Patch 1/2 is to fix some indent level. Given that we have kernels out there with this issue, patch 2/2 also fix sctp_raw_to_bind_addrs. v1 -> v2: Explain why we didn't filter the duplicate addresses when global address list gets updated in patch 2/2 changelog. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
bh1770glc.txt
Kernel driver bh1770glc
=======================
Supported chips:
ROHM BH1770GLC
OSRAM SFH7770
Data sheet:
Not freely available
Author:
Samu Onkalo <samu.p.onkalo@nokia.com>
Description
-----------
BH1770GLC and SFH7770 are combined ambient light and proximity sensors.
ALS and proximity parts operates on their own, but they shares common I2C
interface and interrupt logic. In principle they can run on their own,
but ALS side results are used to estimate reliability of the proximity sensor.
ALS produces 16 bit lux values. The chip contains interrupt logic to produce
low and high threshold interrupts.
Proximity part contains IR-led driver up to 3 IR leds. The chip measures
amount of reflected IR light and produces proximity result. Resolution is
8 bit. Driver supports only one channel. Driver uses ALS results to estimate
reliability of the proximity results. Thus ALS is always running while
proximity detection is needed.
Driver uses threshold interrupts to avoid need for polling the values.
Proximity low interrupt doesn't exists in the chip. This is simulated
by using a delayed work. As long as there is proximity threshold above
interrupts the delayed work is pushed forward. So, when proximity level goes
below the threshold value, there is no interrupt and the delayed work will
finally run. This is handled as no proximity indication.
Chip state is controlled via runtime pm framework when enabled in config.
Calibscale factor is used to hide differences between the chips. By default
value set to neutral state meaning factor of 1.00. To get proper values,
calibrated source of light is needed as a reference. Calibscale factor is set
so that measurement produces about the expected lux value.
SYSFS
-----
chip_id
RO - shows detected chip type and version
power_state
RW - enable / disable chip. Uses counting logic
1 enables the chip
0 disables the chip
lux0_input
RO - measured lux value
sysfs_notify called when threshold interrupt occurs
lux0_sensor_range
RO - lux0_input max value
lux0_rate
RW - measurement rate in Hz
lux0_rate_avail
RO - supported measurement rates
lux0_thresh_above_value
RW - HI level threshold value. All results above the value
trigs an interrupt. 65535 (i.e. sensor_range) disables the above
interrupt.
lux0_thresh_below_value
RW - LO level threshold value. All results below the value
trigs an interrupt. 0 disables the below interrupt.
lux0_calibscale
RW - calibration value. Set to neutral value by default.
Output results are multiplied with calibscale / calibscale_default
value.
lux0_calibscale_default
RO - neutral calibration value
prox0_raw
RO - measured proximity value
sysfs_notify called when threshold interrupt occurs
prox0_sensor_range
RO - prox0_raw max value
prox0_raw_en
RW - enable / disable proximity - uses counting logic
1 enables the proximity
0 disables the proximity
prox0_thresh_above_count
RW - number of proximity interrupts needed before triggering the event
prox0_rate_above
RW - Measurement rate (in Hz) when the level is above threshold
i.e. when proximity on has been reported.
prox0_rate_below
RW - Measurement rate (in Hz) when the level is below threshold
i.e. when proximity off has been reported.
prox0_rate_avail
RO - Supported proximity measurement rates in Hz
prox0_thresh_above0_value
RW - threshold level which trigs proximity events.
Filtered by persistence filter (prox0_thresh_above_count)
prox0_thresh_above1_value
RW - threshold level which trigs event immediately
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...