Revision ba1aa084d6fb725a4c026adf69845ca60bab3b36 authored by Ursula Braun on 24 May 2006, 07:51:13 UTC, committed by Jeff Garzik on 27 May 2006, 01:56:41 UTC
From: Frank Blaschka <Frank.Blaschka@de.ibm.com> From: Frank Pavlic <fpavlic@de.ibm.com> - fix fake_ll during initial device bringup. fake_ll was not active after first start of the device. Problem only occured when qeth was built without IPV6 support. - avoid skb usage after invocation of qeth_flush_buffers, because skb might already be freed. - remove yet another useless netif_wake_queue in qeth_softsetup_ipv6 since this function is only called when device is going online. In this case card->state will never be in state UP. So let the net_device queue down . Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
1 parent b85e1fa
mono.txt
Mono(tm) Binary Kernel Support for Linux
-----------------------------------------
To configure Linux to automatically execute Mono-based .NET binaries
(in the form of .exe files) without the need to use the mono CLR
wrapper, you can use the BINFMT_MISC kernel support.
This will allow you to execute Mono-based .NET binaries just like any
other program after you have done the following:
1) You MUST FIRST install the Mono CLR support, either by downloading
a binary package, a source tarball or by installing from CVS. Binary
packages for several distributions can be found at:
http://go-mono.com/download.html
Instructions for compiling Mono can be found at:
http://www.go-mono.com/compiling.html
Once the Mono CLR support has been installed, just check that
/usr/bin/mono (which could be located elsewhere, for example
/usr/local/bin/mono) is working.
2) You have to compile BINFMT_MISC either as a module or into
the kernel (CONFIG_BINFMT_MISC) and set it up properly.
If you choose to compile it as a module, you will have
to insert it manually with modprobe/insmod, as kmod
can not be easily supported with binfmt_misc.
Read the file 'binfmt_misc.txt' in this directory to know
more about the configuration process.
3) Add the following entries to /etc/rc.local or similar script
to be run at system startup:
# Insert BINFMT_MISC module into the kernel
if [ ! -e /proc/sys/fs/binfmt_misc/register ]; then
/sbin/modprobe binfmt_misc
# Some distributions, like Fedora Core, perform
# the following command automatically when the
# binfmt_misc module is loaded into the kernel.
# Thus, it is possible that the following line
# is not needed at all. Look at /etc/modprobe.conf
# to check whether this is applicable or not.
mount -t binfmt_misc none /proc/sys/fs/binfmt_misc
fi
# Register support for .NET CLR binaries
if [ -e /proc/sys/fs/binfmt_misc/register ]; then
# Replace /usr/bin/mono with the correct pathname to
# the Mono CLR runtime (usually /usr/local/bin/mono
# when compiling from sources or CVS).
echo ':CLR:M::MZ::/usr/bin/mono:' > /proc/sys/fs/binfmt_misc/register
else
echo "No binfmt_misc support"
exit 1
fi
4) Check that .exe binaries can be ran without the need of a
wrapper script, simply by launching the .exe file directly
from a command prompt, for example:
/usr/bin/xsd.exe
NOTE: If this fails with a permission denied error, check
that the .exe file has execute permissions.
Computing file changes ...