Revision bb4c7e9a9908548b458f34afb2fee74dc0d49f90 authored by Linus Torvalds on 23 February 2012, 23:38:57 UTC, committed by Linus Torvalds on 23 February 2012, 23:38:57 UTC
A fix from Jesper Juhl removes an assignment in an ASSERT when a compare is intended. Two fixes from Mitsuo Hayasaka address off-by-ones in XFS quota enforcement. * 'for-linus' of git://oss.sgi.com/xfs/xfs: xfs: make inode quota check more general xfs: change available ranges of softlimit and hardlimit in quota check XFS: xfs_trans_add_item() - don't assign in ASSERT() when compare is intended
board-u5500-sdi.c
/*
* Copyright (C) ST-Ericsson SA 2010
*
* Author: Hanumath Prasad <ulf.hansson@stericsson.com>
* License terms: GNU General Public License (GPL) version 2
*/
#include <linux/amba/mmci.h>
#include <linux/mmc/host.h>
#include <plat/pincfg.h>
#include <plat/gpio-nomadik.h>
#include <mach/db5500-regs.h>
#include <plat/ste_dma40.h>
#include "pins-db5500.h"
#include "devices-db5500.h"
#include "ste-dma40-db5500.h"
static pin_cfg_t u5500_sdi_pins[] = {
/* SDI0 (POP eMMC) */
GPIO5_MC0_DAT0 | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO6_MC0_DAT1 | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO7_MC0_DAT2 | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO8_MC0_DAT3 | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO9_MC0_DAT4 | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO10_MC0_DAT5 | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO11_MC0_DAT6 | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO12_MC0_DAT7 | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO13_MC0_CMD | PIN_DIR_INPUT | PIN_PULL_UP,
GPIO14_MC0_CLK | PIN_DIR_OUTPUT | PIN_VAL_LOW,
};
#ifdef CONFIG_STE_DMA40
struct stedma40_chan_cfg u5500_sdi0_dma_cfg_rx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = STEDMA40_PERIPH_TO_MEM,
.src_dev_type = DB5500_DMA_DEV24_SDMMC0_RX,
.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
.src_info.data_width = STEDMA40_WORD_WIDTH,
.dst_info.data_width = STEDMA40_WORD_WIDTH,
};
static struct stedma40_chan_cfg u5500_sdi0_dma_cfg_tx = {
.mode = STEDMA40_MODE_LOGICAL,
.dir = STEDMA40_MEM_TO_PERIPH,
.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
.dst_dev_type = DB5500_DMA_DEV24_SDMMC0_TX,
.src_info.data_width = STEDMA40_WORD_WIDTH,
.dst_info.data_width = STEDMA40_WORD_WIDTH,
};
#endif
static struct mmci_platform_data u5500_sdi0_data = {
.ocr_mask = MMC_VDD_165_195,
.f_max = 50000000,
.capabilities = MMC_CAP_4_BIT_DATA |
MMC_CAP_8_BIT_DATA |
MMC_CAP_MMC_HIGHSPEED,
.gpio_cd = -1,
.gpio_wp = -1,
#ifdef CONFIG_STE_DMA40
.dma_filter = stedma40_filter,
.dma_rx_param = &u5500_sdi0_dma_cfg_rx,
.dma_tx_param = &u5500_sdi0_dma_cfg_tx,
#endif
};
void __init u5500_sdi_init(void)
{
nmk_config_pins(u5500_sdi_pins, ARRAY_SIZE(u5500_sdi_pins));
db5500_add_sdi0(&u5500_sdi0_data);
}
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...