Revision befb1b3c2703897c5b8ffb0044dc5d0e5f27c5d7 authored by Reinette Chatre on 19 September 2018, 17:29:06 UTC, committed by Thomas Gleixner on 28 September 2018, 20:44:53 UTC
It is possible that a failure can occur during the scheduling of a pinned event. The initial portion of perf_event_read_local() contains the various error checks an event should pass before it can be considered valid. Ensure that the potential scheduling failure of a pinned event is checked for and have a credible error. Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: fenghua.yu@intel.com Cc: tony.luck@intel.com Cc: acme@kernel.org Cc: gavin.hindman@intel.com Cc: jithu.joseph@intel.com Cc: dave.hansen@intel.com Cc: hpa@zytor.com Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/6486385d1f30336e9973b24c8c65f5079543d3d3.1537377064.git.reinette.chatre@intel.com
1 parent c307aaf
ltc2945
Kernel driver ltc2945
=====================
Supported chips:
* Linear Technology LTC2945
Prefix: 'ltc2945'
Addresses scanned: -
Datasheet:
http://cds.linear.com/docs/en/datasheet/2945fa.pdf
Author: Guenter Roeck <linux@roeck-us.net>
Description
-----------
The LTC2945 is a rail-to-rail system monitor that measures current, voltage,
and power consumption.
Usage Notes
-----------
This driver does not probe for LTC2945 devices, since there is no register
which can be safely used to identify the chip. You will have to instantiate
the devices explicitly.
Example: the following will load the driver for an LTC2945 at address 0x10
on I2C bus #1:
$ modprobe ltc2945
$ echo ltc2945 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
Sysfs entries
-------------
Voltage readings provided by this driver are reported as obtained from the ADC
registers. If a set of voltage divider resistors is installed, calculate the
real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
value of the divider resistor against the measured voltage and R2 is the value
of the divider resistor against Ground.
Current reading provided by this driver is reported as obtained from the ADC
Current Sense register. The reported value assumes that a 1 mOhm sense resistor
is installed. If a different sense resistor is installed, calculate the real
current by dividing the reported value by the sense resistor value in mOhm.
in1_input VIN voltage (mV). Voltage is measured either at
SENSE+ or VDD pin depending on chip configuration.
in1_min Undervoltage threshold
in1_max Overvoltage threshold
in1_lowest Lowest measured voltage
in1_highest Highest measured voltage
in1_reset_history Write 1 to reset in1 history
in1_min_alarm Undervoltage alarm
in1_max_alarm Overvoltage alarm
in2_input ADIN voltage (mV)
in2_min Undervoltage threshold
in2_max Overvoltage threshold
in2_lowest Lowest measured voltage
in2_highest Highest measured voltage
in2_reset_history Write 1 to reset in2 history
in2_min_alarm Undervoltage alarm
in2_max_alarm Overvoltage alarm
curr1_input SENSE current (mA)
curr1_min Undercurrent threshold
curr1_max Overcurrent threshold
curr1_lowest Lowest measured current
curr1_highest Highest measured current
curr1_reset_history Write 1 to reset curr1 history
curr1_min_alarm Undercurrent alarm
curr1_max_alarm Overcurrent alarm
power1_input Power (in uW). Power is calculated based on SENSE+/VDD
voltage or ADIN voltage depending on chip configuration.
power1_min Low lower threshold
power1_max High power threshold
power1_input_lowest Historical minimum power use
power1_input_highest Historical maximum power use
power1_reset_history Write 1 to reset power1 history
power1_min_alarm Low power alarm
power1_max_alarm High power alarm
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...