Revision dc8c214a9c37eb288b1c4782632649e55d251c68 authored by roel kluin on 01 December 2008, 21:13:51 UTC, committed by Linus Torvalds on 02 December 2008, 03:55:24 UTC
Use __initdata for data, not __init. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1 parent dc924ef
Kconfig
#
# SATA/PATA driver configuration
#
menuconfig ATA
tristate "Serial ATA (prod) and Parallel ATA (experimental) drivers"
depends on HAS_IOMEM
depends on BLOCK
depends on !(M32R || M68K) || BROKEN
select SCSI
---help---
If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or
any other ATA device under Linux, say Y and make sure that you know
the name of your ATA host adapter (the card inside your computer
that "speaks" the ATA protocol, also called ATA controller),
because you will be asked for it.
NOTE: ATA enables basic SCSI support; *however*,
'SCSI disk support', 'SCSI tape support', or
'SCSI CDROM support' may also be needed,
depending on your hardware configuration.
if ATA
config ATA_NONSTANDARD
bool
default n
config ATA_ACPI
bool "ATA ACPI Support"
depends on ACPI && PCI
select ACPI_DOCK
default y
help
This option adds support for ATA-related ACPI objects.
These ACPI objects add the ability to retrieve taskfiles
from the ACPI BIOS and write them to the disk controller.
These objects may be related to performance, security,
power management, or other areas.
You can disable this at kernel boot time by using the
option libata.noacpi=1
config SATA_PMP
bool "SATA Port Multiplier support"
default y
help
This option adds support for SATA Port Multipliers
(the SATA version of an ethernet hub, or SAS expander).
config SATA_AHCI
tristate "AHCI SATA support"
depends on PCI
help
This option enables support for AHCI Serial ATA.
If unsure, say N.
config SATA_SIL24
tristate "Silicon Image 3124/3132 SATA support"
depends on PCI
help
This option enables support for Silicon Image 3124/3132 Serial ATA.
If unsure, say N.
config SATA_FSL
tristate "Freescale 3.0Gbps SATA support"
depends on FSL_SOC
help
This option enables support for Freescale 3.0Gbps SATA controller.
It can be found on MPC837x and MPC8315.
If unsure, say N.
config ATA_SFF
bool "ATA SFF support"
default y
help
This option adds support for ATA controllers with SFF
compliant or similar programming interface.
SFF is the legacy IDE interface that has been around since
the dawn of time. Almost all PATA controllers have an
SFF interface. Many SATA controllers have an SFF interface
when configured into a legacy compatibility mode.
For users with exclusively modern controllers like AHCI,
Silicon Image 3124, or Marvell 6440, you may choose to
disable this uneeded SFF support.
If unsure, say Y.
if ATA_SFF
config SATA_SVW
tristate "ServerWorks Frodo / Apple K2 SATA support"
depends on PCI
help
This option enables support for Broadcom/Serverworks/Apple K2
SATA support.
If unsure, say N.
config ATA_PIIX
tristate "Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support"
depends on PCI
help
This option enables support for ICH5/6/7/8 Serial ATA
and support for PATA on the Intel ESB/ICH/PIIX3/PIIX4 series
host controllers.
If unsure, say N.
config SATA_MV
tristate "Marvell SATA support (HIGHLY EXPERIMENTAL)"
depends on EXPERIMENTAL
help
This option enables support for the Marvell Serial ATA family.
Currently supports 88SX[56]0[48][01] chips.
If unsure, say N.
config SATA_NV
tristate "NVIDIA SATA support"
depends on PCI
help
This option enables support for NVIDIA Serial ATA.
If unsure, say N.
config PDC_ADMA
tristate "Pacific Digital ADMA support"
depends on PCI
help
This option enables support for Pacific Digital ADMA controllers
If unsure, say N.
config SATA_QSTOR
tristate "Pacific Digital SATA QStor support"
depends on PCI
help
This option enables support for Pacific Digital Serial ATA QStor.
If unsure, say N.
config SATA_PROMISE
tristate "Promise SATA TX2/TX4 support"
depends on PCI
help
This option enables support for Promise Serial ATA TX2/TX4.
If unsure, say N.
config SATA_SX4
tristate "Promise SATA SX4 support"
depends on PCI && EXPERIMENTAL
help
This option enables support for Promise Serial ATA SX4.
If unsure, say N.
config SATA_SIL
tristate "Silicon Image SATA support"
depends on PCI
help
This option enables support for Silicon Image Serial ATA.
If unsure, say N.
config SATA_SIS
tristate "SiS 964/965/966/180 SATA support"
depends on PCI
select PATA_SIS
help
This option enables support for SiS Serial ATA on
SiS 964/965/966/180 and Parallel ATA on SiS 180.
The PATA support for SiS 180 requires additionally to
enable the PATA_SIS driver in the config.
If unsure, say N.
config SATA_ULI
tristate "ULi Electronics SATA support"
depends on PCI
help
This option enables support for ULi Electronics SATA.
If unsure, say N.
config SATA_VIA
tristate "VIA SATA support"
depends on PCI
help
This option enables support for VIA Serial ATA.
If unsure, say N.
config SATA_VITESSE
tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
depends on PCI
help
This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
If unsure, say N.
config SATA_INIC162X
tristate "Initio 162x SATA support"
depends on PCI
help
This option enables support for Initio 162x Serial ATA.
config PATA_ACPI
tristate "ACPI firmware driver for PATA"
depends on ATA_ACPI
help
This option enables an ACPI method driver which drives
motherboard PATA controller interfaces through the ACPI
firmware in the BIOS. This driver can sometimes handle
otherwise unsupported hardware.
config PATA_ALI
tristate "ALi PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the ALi ATA interfaces
found on the many ALi chipsets.
If unsure, say N.
config PATA_AMD
tristate "AMD/NVidia PATA support"
depends on PCI
help
This option enables support for the AMD and NVidia PATA
interfaces found on the chipsets for Athlon/Athlon64.
If unsure, say N.
config PATA_ARTOP
tristate "ARTOP 6210/6260 PATA support"
depends on PCI
help
This option enables support for ARTOP PATA controllers.
If unsure, say N.
config PATA_AT32
tristate "Atmel AVR32 PATA support (Experimental)"
depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
help
This option enables support for the IDE devices on the
Atmel AT32AP platform.
If unsure, say N.
config PATA_ATIIXP
tristate "ATI PATA support"
depends on PCI
help
This option enables support for the ATI ATA interfaces
found on the many ATI chipsets.
If unsure, say N.
config PATA_CMD640_PCI
tristate "CMD640 PCI PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the CMD640 PCI IDE
interface chip. Only the primary channel is currently
supported.
If unsure, say N.
config PATA_CMD64X
tristate "CMD64x PATA support"
depends on PCI
help
This option enables support for the CMD64x series chips
except for the CMD640.
If unsure, say N.
config PATA_CS5520
tristate "CS5510/5520 PATA support"
depends on PCI
help
This option enables support for the Cyrix 5510/5520
companion chip used with the MediaGX/Geode processor family.
If unsure, say N.
config PATA_CS5530
tristate "CS5530 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the Cyrix/NatSemi/AMD CS5530
companion chip used with the MediaGX/Geode processor family.
If unsure, say N.
config PATA_CS5535
tristate "CS5535 PATA support (Experimental)"
depends on PCI && X86 && !X86_64 && EXPERIMENTAL
help
This option enables support for the NatSemi/AMD CS5535
companion chip used with the Geode processor family.
If unsure, say N.
config PATA_CS5536
tristate "CS5536 PATA support (Experimental)"
depends on PCI && X86 && !X86_64 && EXPERIMENTAL
help
This option enables support for the AMD CS5536
companion chip used with the Geode LX processor family.
If unsure, say N.
config PATA_CYPRESS
tristate "Cypress CY82C693 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the Cypress/Contaq CY82C693
chipset found in some Alpha systems
If unsure, say N.
config PATA_EFAR
tristate "EFAR SLC90E66 support"
depends on PCI
help
This option enables support for the EFAR SLC90E66
IDE controller found on some older machines.
If unsure, say N.
config ATA_GENERIC
tristate "Generic ATA support"
depends on PCI
help
This option enables support for generic BIOS configured
ATA controllers via the new ATA layer
If unsure, say N.
config PATA_HPT366
tristate "HPT 366/368 PATA support"
depends on PCI
help
This option enables support for the HPT 366 and 368
PATA controllers via the new ATA layer.
If unsure, say N.
config PATA_HPT37X
tristate "HPT 370/370A/371/372/374/302 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the majority of the later HPT
PATA controllers via the new ATA layer.
If unsure, say N.
config PATA_HPT3X2N
tristate "HPT 372N/302N PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the N variant HPT PATA
controllers via the new ATA layer
If unsure, say N.
config PATA_HPT3X3
tristate "HPT 343/363 PATA support"
depends on PCI
help
This option enables support for the HPT 343/363
PATA controllers via the new ATA layer
If unsure, say N.
config PATA_HPT3X3_DMA
bool "HPT 343/363 DMA support (Experimental)"
depends on PATA_HPT3X3
help
This option enables DMA support for the HPT343/363
controllers. Enable with care as there are still some
problems with DMA on this chipset.
config PATA_ISAPNP
tristate "ISA Plug and Play PATA support (Experimental)"
depends on EXPERIMENTAL && ISAPNP
help
This option enables support for ISA plug & play ATA
controllers such as those found on old soundcards.
If unsure, say N.
config PATA_IT821X
tristate "IT8211/2 PATA support"
depends on PCI
help
This option enables support for the ITE 8211 and 8212
PATA controllers via the new ATA layer, including RAID
mode.
If unsure, say N.
config PATA_IT8213
tristate "IT8213 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the ITE 821 PATA
controllers via the new ATA layer.
If unsure, say N.
config PATA_JMICRON
tristate "JMicron PATA support"
depends on PCI
help
Enable support for the JMicron IDE controller, via the new
ATA layer.
If unsure, say N.
config PATA_LEGACY
tristate "Legacy ISA PATA support (Experimental)"
depends on ISA && EXPERIMENTAL
help
This option enables support for ISA/VLB bus legacy PATA
ports and allows them to be accessed via the new ATA layer.
If unsure, say N.
config PATA_TRIFLEX
tristate "Compaq Triflex PATA support"
depends on PCI
help
Enable support for the Compaq 'Triflex' IDE controller as found
on many Compaq Pentium-Pro systems, via the new ATA layer.
If unsure, say N.
config PATA_MARVELL
tristate "Marvell PATA support via legacy mode"
depends on PCI
help
This option enables limited support for the Marvell 88SE61xx ATA
controllers. If you wish to use only the SATA ports then select
the AHCI driver alone. If you wish to the use the PATA port or
both SATA and PATA include this driver.
If unsure, say N.
config PATA_MPC52xx
tristate "Freescale MPC52xx SoC internal IDE"
depends on PPC_MPC52xx
help
This option enables support for integrated IDE controller
of the Freescale MPC52xx SoC.
If unsure, say N.
config PATA_MPIIX
tristate "Intel PATA MPIIX support"
depends on PCI
help
This option enables support for MPIIX PATA support.
If unsure, say N.
config PATA_OLDPIIX
tristate "Intel PATA old PIIX support"
depends on PCI
help
This option enables support for early PIIX PATA support.
If unsure, say N.
config PATA_NETCELL
tristate "NETCELL Revolution RAID support"
depends on PCI
help
This option enables support for the Netcell Revolution RAID
PATA controller.
If unsure, say N.
config PATA_NINJA32
tristate "Ninja32/Delkin Cardbus ATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the Ninja32, Delkin and
possibly other brands of Cardbus ATA adapter
If unsure, say N.
config PATA_NS87410
tristate "Nat Semi NS87410 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the National Semiconductor
NS87410 PCI-IDE controller.
If unsure, say N.
config PATA_NS87415
tristate "Nat Semi NS87415 PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the National Semiconductor
NS87415 PCI-IDE controller.
If unsure, say N.
config PATA_OPTI
tristate "OPTI621/6215 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables full PIO support for the early Opti ATA
controllers found on some old motherboards.
If unsure, say N.
config PATA_OPTIDMA
tristate "OPTI FireStar PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables DMA/PIO support for the later OPTi
controllers found on some old motherboards and in some
laptops.
If unsure, say N.
config PATA_PCMCIA
tristate "PCMCIA PATA support"
depends on PCMCIA
help
This option enables support for PCMCIA ATA interfaces, including
compact flash card adapters via the new ATA layer.
If unsure, say N.
config PATA_PDC_OLD
tristate "Older Promise PATA controller support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the Promise 20246, 20262, 20263,
20265 and 20267 adapters.
If unsure, say N.
config PATA_QDI
tristate "QDI VLB PATA support"
depends on ISA
help
Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
config PATA_RADISYS
tristate "RADISYS 82600 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the RADISYS 82600
PATA controllers via the new ATA layer
If unsure, say N.
config PATA_RB532
tristate "RouterBoard 532 PATA CompactFlash support"
depends on MIKROTIK_RB532
help
This option enables support for the RouterBoard 532
PATA CompactFlash controller.
If unsure, say N.
config PATA_RZ1000
tristate "PC Tech RZ1000 PATA support"
depends on PCI
help
This option enables basic support for the PC Tech RZ1000/1
PATA controllers via the new ATA layer
If unsure, say N.
config PATA_SC1200
tristate "SC1200 PATA support (Very Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for the NatSemi/AMD SC1200 SoC
companion chip used with the Geode processor family.
If unsure, say N.
config PATA_SERVERWORKS
tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support"
depends on PCI
help
This option enables support for the Serverworks OSB4/CSB5/CSB6 and
HT1000 PATA controllers, via the new ATA layer.
If unsure, say N.
config PATA_PDC2027X
tristate "Promise PATA 2027x support"
depends on PCI
help
This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
If unsure, say N.
config PATA_SIL680
tristate "CMD / Silicon Image 680 PATA support"
depends on PCI
help
This option enables support for CMD / Silicon Image 680 PATA.
If unsure, say N.
config PATA_SIS
tristate "SiS PATA support (Experimental)"
depends on PCI && EXPERIMENTAL
help
This option enables support for SiS PATA controllers
If unsure, say N.
config PATA_VIA
tristate "VIA PATA support"
depends on PCI
help
This option enables support for the VIA PATA interfaces
found on the many VIA chipsets.
If unsure, say N.
config PATA_WINBOND
tristate "Winbond SL82C105 PATA support"
depends on PCI
help
This option enables support for SL82C105 PATA devices found in the
Netwinder and some other systems
If unsure, say N.
config PATA_WINBOND_VLB
tristate "Winbond W83759A VLB PATA support (Experimental)"
depends on ISA && EXPERIMENTAL
help
Support for the Winbond W83759A controller on Vesa Local Bus
systems.
config HAVE_PATA_PLATFORM
bool
help
This is an internal configuration node for any machine that
uses pata-platform driver to enable the relevant driver in the
configuration structure without having to submit endless patches
to update the PATA_PLATFORM entry.
config PATA_PLATFORM
tristate "Generic platform device PATA support"
depends on EMBEDDED || PPC || HAVE_PATA_PLATFORM
help
This option enables support for generic directly connected ATA
devices commonly found on embedded systems.
If unsure, say N.
config PATA_OF_PLATFORM
tristate "OpenFirmware platform device PATA support"
depends on PATA_PLATFORM && PPC_OF
help
This option enables support for generic directly connected ATA
devices commonly found on embedded systems with OpenFirmware
bindings.
If unsure, say N.
config PATA_ICSIDE
tristate "Acorn ICS PATA support"
depends on ARM && ARCH_ACORN
help
On Acorn systems, say Y here if you wish to use the ICS PATA
interface card. This is not required for ICS partition support.
If you are unsure, say N to this.
config PATA_IXP4XX_CF
tristate "IXP4XX Compact Flash support"
depends on ARCH_IXP4XX
help
This option enables support for a Compact Flash connected on
the ixp4xx expansion bus. This driver had been written for
Loft/Avila boards in mind but can work with others.
If unsure, say N.
config PATA_SCC
tristate "Toshiba's Cell Reference Set IDE support"
depends on PCI && PPC_CELLEB
help
This option enables support for the built-in IDE controller on
Toshiba Cell Reference Board.
If unsure, say N.
config PATA_SCH
tristate "Intel SCH PATA support"
depends on PCI
help
This option enables support for Intel SCH PATA on the Intel
SCH (US15W, US15L, UL11L) series host controllers.
If unsure, say N.
config PATA_BF54X
tristate "Blackfin 54x ATAPI support"
depends on BF542 || BF548 || BF549
help
This option enables support for the built-in ATAPI controller on
Blackfin 54x family chips.
If unsure, say N.
endif # ATA_SFF
endif # ATA
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...