Revision df8d06ade6eed9077f658ac8696fc1cb5c081220 authored by Linus Torvalds on 16 May 2011, 15:55:49 UTC, committed by Linus Torvalds on 16 May 2011, 15:55:49 UTC
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: OMAP3: set the core dpll clk rate in its set_rate function omap: iommu: Return IRQ_HANDLED in fault handler when no fault occured
board-flexibity.c
/*
* linux/arch/arm/mach-at91/board-flexibity.c
*
* Copyright (C) 2010 Flexibity
* Copyright (C) 2005 SAN People
* Copyright (C) 2006 Atmel
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/input.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/hardware.h>
#include <mach/board.h>
#include "generic.h"
static void __init flexibity_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91sam9260_initialize(18432000);
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static void __init flexibity_init_irq(void)
{
at91sam9260_init_interrupts(NULL);
}
/* USB Host port */
static struct at91_usbh_data __initdata flexibity_usbh_data = {
.ports = 2,
};
/* USB Device port */
static struct at91_udc_data __initdata flexibity_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
};
/* SPI devices */
static struct spi_board_info flexibity_spi_devices[] = {
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.chip_select = 1,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
};
/* MCI (SD/MMC) */
static struct at91_mmc_data __initdata flexibity_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.det_pin = AT91_PIN_PC9,
.wp_pin = AT91_PIN_PC4,
};
/* LEDs */
static struct gpio_led flexibity_leds[] = {
{
.name = "usb1:green",
.gpio = AT91_PIN_PA12,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "usb1:red",
.gpio = AT91_PIN_PA13,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "usb2:green",
.gpio = AT91_PIN_PB26,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "usb2:red",
.gpio = AT91_PIN_PB27,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "usb3:green",
.gpio = AT91_PIN_PC8,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "usb3:red",
.gpio = AT91_PIN_PC6,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "usb4:green",
.gpio = AT91_PIN_PB4,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "usb4:red",
.gpio = AT91_PIN_PB5,
.active_low = 1,
.default_trigger = "default-on",
}
};
static void __init flexibity_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&flexibity_usbh_data);
/* USB Device */
at91_add_device_udc(&flexibity_udc_data);
/* SPI */
at91_add_device_spi(flexibity_spi_devices,
ARRAY_SIZE(flexibity_spi_devices));
/* MMC */
at91_add_device_mmc(0, &flexibity_mmc_data);
/* LEDs */
at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds));
}
MACHINE_START(FLEXIBITY, "Flexibity Connect")
/* Maintainer: Maxim Osipov */
.boot_params = AT91_SDRAM_BASE + 0x100,
.timer = &at91sam926x_timer,
.map_io = flexibity_map_io,
.init_irq = flexibity_init_irq,
.init_machine = flexibity_board_init,
MACHINE_END
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...