Revision ebfddb3d447f5267c76680ea4d242e6f9bcafa87 authored by Arnd Bergmann on 13 September 2017, 23:28:23 UTC, committed by Linus Torvalds on 14 September 2017, 01:53:15 UTC
gcc points out a minor bug in the handling of unknown cookie types, which could result in a string overflow when the integer is copied into a 3-byte string: fs/fscache/object-list.c: In function 'fscache_objlist_show': fs/fscache/object-list.c:265:19: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=] sprintf(_type, "%02u", cookie->def->type); ^~~~~~ fs/fscache/object-list.c:265:4: note: 'sprintf' output between 3 and 4 bytes into a destination of size 3 This is currently harmless as no code sets a type other than 0 or 1, but it makes sense to use snprintf() here to avoid overflowing the array if that changes. Link: http://lkml.kernel.org/r/20170714120720.906842-22-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1 parent 8185f57
zorro.txt
========================================
Writing Device Drivers for Zorro Devices
========================================
:Author: Written by Geert Uytterhoeven <geert@linux-m68k.org>
:Last revised: September 5, 2003
Introduction
------------
The Zorro bus is the bus used in the Amiga family of computers. Thanks to
AutoConfig(tm), it's 100% Plug-and-Play.
There are two types of Zorro buses, Zorro II and Zorro III:
- The Zorro II address space is 24-bit and lies within the first 16 MB of the
Amiga's address map.
- Zorro III is a 32-bit extension of Zorro II, which is backwards compatible
with Zorro II. The Zorro III address space lies outside the first 16 MB.
Probing for Zorro Devices
-------------------------
Zorro devices are found by calling ``zorro_find_device()``, which returns a
pointer to the ``next`` Zorro device with the specified Zorro ID. A probe loop
for the board with Zorro ID ``ZORRO_PROD_xxx`` looks like::
struct zorro_dev *z = NULL;
while ((z = zorro_find_device(ZORRO_PROD_xxx, z))) {
if (!zorro_request_region(z->resource.start+MY_START, MY_SIZE,
"My explanation"))
...
}
``ZORRO_WILDCARD`` acts as a wildcard and finds any Zorro device. If your driver
supports different types of boards, you can use a construct like::
struct zorro_dev *z = NULL;
while ((z = zorro_find_device(ZORRO_WILDCARD, z))) {
if (z->id != ZORRO_PROD_xxx1 && z->id != ZORRO_PROD_xxx2 && ...)
continue;
if (!zorro_request_region(z->resource.start+MY_START, MY_SIZE,
"My explanation"))
...
}
Zorro Resources
---------------
Before you can access a Zorro device's registers, you have to make sure it's
not yet in use. This is done using the I/O memory space resource management
functions::
request_mem_region()
release_mem_region()
Shortcuts to claim the whole device's address space are provided as well::
zorro_request_device
zorro_release_device
Accessing the Zorro Address Space
---------------------------------
The address regions in the Zorro device resources are Zorro bus address
regions. Due to the identity bus-physical address mapping on the Zorro bus,
they are CPU physical addresses as well.
The treatment of these regions depends on the type of Zorro space:
- Zorro II address space is always mapped and does not have to be mapped
explicitly using z_ioremap().
Conversion from bus/physical Zorro II addresses to kernel virtual addresses
and vice versa is done using::
virt_addr = ZTWO_VADDR(bus_addr);
bus_addr = ZTWO_PADDR(virt_addr);
- Zorro III address space must be mapped explicitly using z_ioremap() first
before it can be accessed::
virt_addr = z_ioremap(bus_addr, size);
...
z_iounmap(virt_addr);
References
----------
#. linux/include/linux/zorro.h
#. linux/include/uapi/linux/zorro.h
#. linux/include/uapi/linux/zorro_ids.h
#. linux/arch/m68k/include/asm/zorro.h
#. linux/drivers/zorro
#. /proc/bus/zorro
![swh spinner](/static/img/swh-spinner.gif)
Computing file changes ...