https://github.com/torvalds/linux
Revision ecefc36b41ac0fe92d76273a23faf27b2da13411 authored by Linus Torvalds on 22 December 2011, 02:29:26 UTC, committed by Linus Torvalds on 22 December 2011, 02:29:26 UTC
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: net: Add a flow_cache_flush_deferred function ipv4: reintroduce route cache garbage collector net: have ipconfig not wait if no dev is available sctp: Do not account for sizeof(struct sk_buff) in estimated rwnd asix: new device id davinci-cpdma: fix locking issue in cpdma_chan_stop sctp: fix incorrect overflow check on autoclose r8169: fix Config2 MSIEnable bit setting. llc: llc_cmsg_rcv was getting called after sk_eat_skb. net: bpf_jit: fix an off-one bug in x86_64 cond jump target iwlwifi: update SCD BC table for all SCD queues Revert "Bluetooth: Revert: Fix L2CAP connection establishment" Bluetooth: Clear RFCOMM session timer when disconnecting last channel Bluetooth: Prevent uninitialized data access in L2CAP configuration iwlwifi: allow to switch to HT40 if not associated iwlwifi: tx_sync only on PAN context mwifiex: avoid double list_del in command cancel path ath9k: fix max phy rate at rate control init nfc: signedness bug in __nci_request() iwlwifi: do not set the sequence control bit is not needed
Tip revision: ecefc36b41ac0fe92d76273a23faf27b2da13411 authored by Linus Torvalds on 22 December 2011, 02:29:26 UTC
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Tip revision: ecefc36
btmrvl.txt
=======================================================================
README for btmrvl driver
=======================================================================
All commands are used via debugfs interface.
=====================
Set/get driver configurations:
Path: /debug/btmrvl/config/
gpiogap=[n]
hscfgcmd
These commands are used to configure the host sleep parameters.
bit 8:0 -- Gap
bit 16:8 -- GPIO
where GPIO is the pin number of GPIO used to wake up the host.
It could be any valid GPIO pin# (e.g. 0-7) or 0xff (SDIO interface
wakeup will be used instead).
where Gap is the gap in milli seconds between wakeup signal and
wakeup event, or 0xff for special host sleep setting.
Usage:
# Use SDIO interface to wake up the host and set GAP to 0x80:
echo 0xff80 > /debug/btmrvl/config/gpiogap
echo 1 > /debug/btmrvl/config/hscfgcmd
# Use GPIO pin #3 to wake up the host and set GAP to 0xff:
echo 0x03ff > /debug/btmrvl/config/gpiogap
echo 1 > /debug/btmrvl/config/hscfgcmd
psmode=[n]
pscmd
These commands are used to enable/disable auto sleep mode
where the option is:
1 -- Enable auto sleep mode
0 -- Disable auto sleep mode
Usage:
# Enable auto sleep mode
echo 1 > /debug/btmrvl/config/psmode
echo 1 > /debug/btmrvl/config/pscmd
# Disable auto sleep mode
echo 0 > /debug/btmrvl/config/psmode
echo 1 > /debug/btmrvl/config/pscmd
hsmode=[n]
hscmd
These commands are used to enable host sleep or wake up firmware
where the option is:
1 -- Enable host sleep
0 -- Wake up firmware
Usage:
# Enable host sleep
echo 1 > /debug/btmrvl/config/hsmode
echo 1 > /debug/btmrvl/config/hscmd
# Wake up firmware
echo 0 > /debug/btmrvl/config/hsmode
echo 1 > /debug/btmrvl/config/hscmd
======================
Get driver status:
Path: /debug/btmrvl/status/
Usage:
cat /debug/btmrvl/status/<args>
where the args are:
curpsmode
This command displays current auto sleep status.
psstate
This command display the power save state.
hsstate
This command display the host sleep state.
txdnldrdy
This command displays the value of Tx download ready flag.
=====================
Use hcitool to issue raw hci command, refer to hcitool manual
Usage: Hcitool cmd <ogf> <ocf> [Parameters]
Interface Control Command
hcitool cmd 0x3f 0x5b 0xf5 0x01 0x00 --Enable All interface
hcitool cmd 0x3f 0x5b 0xf5 0x01 0x01 --Enable Wlan interface
hcitool cmd 0x3f 0x5b 0xf5 0x01 0x02 --Enable BT interface
hcitool cmd 0x3f 0x5b 0xf5 0x00 0x00 --Disable All interface
hcitool cmd 0x3f 0x5b 0xf5 0x00 0x01 --Disable Wlan interface
hcitool cmd 0x3f 0x5b 0xf5 0x00 0x02 --Disable BT interface
=======================================================================
SD8688 firmware:
/lib/firmware/sd8688_helper.bin
/lib/firmware/sd8688.bin
The images can be downloaded from:
git.infradead.org/users/dwmw2/linux-firmware.git/libertas/
Computing file changes ...
