Revision fc9bbca8f650e5f738af8806317c0a041a48ae4a authored by Linus Torvalds on 19 April 2013, 16:57:35 UTC, committed by Linus Torvalds on 19 April 2013, 16:57:35 UTC
This is my example conversion of a few existing mmap users.  The
fb_mmap() case is a good example because it is a bit more complicated
than some: fb_mmap() mmaps one of two different memory areas depending
on the page offset of the mmap (but happily there is never any mixing of
the two, so the helper function still works).

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1 parent 8558e4a
Raw File
resend.c
/*
 * linux/kernel/irq/resend.c
 *
 * Copyright (C) 1992, 1998-2006 Linus Torvalds, Ingo Molnar
 * Copyright (C) 2005-2006, Thomas Gleixner
 *
 * This file contains the IRQ-resend code
 *
 * If the interrupt is waiting to be processed, we try to re-run it.
 * We can't directly run it from here since the caller might be in an
 * interrupt-protected region. Not all irq controller chips can
 * retrigger interrupts at the hardware level, so in those cases
 * we allow the resending of IRQs via a tasklet.
 */

#include <linux/irq.h>
#include <linux/module.h>
#include <linux/random.h>
#include <linux/interrupt.h>

#include "internals.h"

#ifdef CONFIG_HARDIRQS_SW_RESEND

/* Bitmap to handle software resend of interrupts: */
static DECLARE_BITMAP(irqs_resend, IRQ_BITMAP_BITS);

/*
 * Run software resends of IRQ's
 */
static void resend_irqs(unsigned long arg)
{
	struct irq_desc *desc;
	int irq;

	while (!bitmap_empty(irqs_resend, nr_irqs)) {
		irq = find_first_bit(irqs_resend, nr_irqs);
		clear_bit(irq, irqs_resend);
		desc = irq_to_desc(irq);
		local_irq_disable();
		desc->handle_irq(irq, desc);
		local_irq_enable();
	}
}

/* Tasklet to handle resend: */
static DECLARE_TASKLET(resend_tasklet, resend_irqs, 0);

#endif

/*
 * IRQ resend
 *
 * Is called with interrupts disabled and desc->lock held.
 */
void check_irq_resend(struct irq_desc *desc, unsigned int irq)
{
	/*
	 * We do not resend level type interrupts. Level type
	 * interrupts are resent by hardware when they are still
	 * active. Clear the pending bit so suspend/resume does not
	 * get confused.
	 */
	if (irq_settings_is_level(desc)) {
		desc->istate &= ~IRQS_PENDING;
		return;
	}
	if (desc->istate & IRQS_REPLAY)
		return;
	if (desc->istate & IRQS_PENDING) {
		desc->istate &= ~IRQS_PENDING;
		desc->istate |= IRQS_REPLAY;

		if (!desc->irq_data.chip->irq_retrigger ||
		    !desc->irq_data.chip->irq_retrigger(&desc->irq_data)) {
#ifdef CONFIG_HARDIRQS_SW_RESEND
			/*
			 * If the interrupt has a parent irq and runs
			 * in the thread context of the parent irq,
			 * retrigger the parent.
			 */
			if (desc->parent_irq &&
			    irq_settings_is_nested_thread(desc))
				irq = desc->parent_irq;
			/* Set it pending and activate the softirq: */
			set_bit(irq, irqs_resend);
			tasklet_schedule(&resend_tasklet);
#endif
		}
	}
}
back to top