swh:1:snp:173f8deb0c56c557784b4fd217e7608ac6197844
Tip revision: f6cede5b49e822ebc41a099fe41ab4989f64e2cb authored by Linus Torvalds on 06 March 2016, 22:48:03 UTC
Linux 4.5-rc7
Linux 4.5-rc7
Tip revision: f6cede5
bcache.txt
Say you've got a big slow raid 6, and an X-25E or three. Wouldn't it be
nice if you could use them as cache... Hence bcache.
Wiki and git repositories are at:
http://bcache.evilpiepirate.org
http://evilpiepirate.org/git/linux-bcache.git
http://evilpiepirate.org/git/bcache-tools.git
It's designed around the performance characteristics of SSDs - it only allocates
in erase block sized buckets, and it uses a hybrid btree/log to track cached
extants (which can be anywhere from a single sector to the bucket size). It's
designed to avoid random writes at all costs; it fills up an erase block
sequentially, then issues a discard before reusing it.
Both writethrough and writeback caching are supported. Writeback defaults to
off, but can be switched on and off arbitrarily at runtime. Bcache goes to
great lengths to protect your data - it reliably handles unclean shutdown. (It
doesn't even have a notion of a clean shutdown; bcache simply doesn't return
writes as completed until they're on stable storage).
Writeback caching can use most of the cache for buffering writes - writing
dirty data to the backing device is always done sequentially, scanning from the
start to the end of the index.
Since random IO is what SSDs excel at, there generally won't be much benefit
to caching large sequential IO. Bcache detects sequential IO and skips it;
it also keeps a rolling average of the IO sizes per task, and as long as the
average is above the cutoff it will skip all IO from that task - instead of
caching the first 512k after every seek. Backups and large file copies should
thus entirely bypass the cache.
In the event of a data IO error on the flash it will try to recover by reading
from disk or invalidating cache entries. For unrecoverable errors (meta data
or dirty data), caching is automatically disabled; if dirty data was present
in the cache it first disables writeback caching and waits for all dirty data
to be flushed.
Getting started:
You'll need make-bcache from the bcache-tools repository. Both the cache device
and backing device must be formatted before use.
make-bcache -B /dev/sdb
make-bcache -C /dev/sdc
make-bcache has the ability to format multiple devices at the same time - if
you format your backing devices and cache device at the same time, you won't
have to manually attach:
make-bcache -B /dev/sda /dev/sdb -C /dev/sdc
bcache-tools now ships udev rules, and bcache devices are known to the kernel
immediately. Without udev, you can manually register devices like this:
echo /dev/sdb > /sys/fs/bcache/register
echo /dev/sdc > /sys/fs/bcache/register
Registering the backing device makes the bcache device show up in /dev; you can
now format it and use it as normal. But the first time using a new bcache
device, it'll be running in passthrough mode until you attach it to a cache.
See the section on attaching.
The devices show up as:
/dev/bcache<N>
As well as (with udev):
/dev/bcache/by-uuid/<uuid>
/dev/bcache/by-label/<label>
To get started:
mkfs.ext4 /dev/bcache0
mount /dev/bcache0 /mnt
You can control bcache devices through sysfs at /sys/block/bcache<N>/bcache .
Cache devices are managed as sets; multiple caches per set isn't supported yet
but will allow for mirroring of metadata and dirty data in the future. Your new
cache set shows up as /sys/fs/bcache/<UUID>
ATTACHING:
After your cache device and backing device are registered, the backing device
must be attached to your cache set to enable caching. Attaching a backing
device to a cache set is done thusly, with the UUID of the cache set in
/sys/fs/bcache:
echo <CSET-UUID> > /sys/block/bcache0/bcache/attach
This only has to be done once. The next time you reboot, just reregister all
your bcache devices. If a backing device has data in a cache somewhere, the
/dev/bcache<N> device won't be created until the cache shows up - particularly
important if you have writeback caching turned on.
If you're booting up and your cache device is gone and never coming back, you
can force run the backing device:
echo 1 > /sys/block/sdb/bcache/running
(You need to use /sys/block/sdb (or whatever your backing device is called), not
/sys/block/bcache0, because bcache0 doesn't exist yet. If you're using a
partition, the bcache directory would be at /sys/block/sdb/sdb2/bcache)
The backing device will still use that cache set if it shows up in the future,
but all the cached data will be invalidated. If there was dirty data in the
cache, don't expect the filesystem to be recoverable - you will have massive
filesystem corruption, though ext4's fsck does work miracles.
ERROR HANDLING:
Bcache tries to transparently handle IO errors to/from the cache device without
affecting normal operation; if it sees too many errors (the threshold is
configurable, and defaults to 0) it shuts down the cache device and switches all
the backing devices to passthrough mode.
- For reads from the cache, if they error we just retry the read from the
backing device.
- For writethrough writes, if the write to the cache errors we just switch to
invalidating the data at that lba in the cache (i.e. the same thing we do for
a write that bypasses the cache)
- For writeback writes, we currently pass that error back up to the
filesystem/userspace. This could be improved - we could retry it as a write
that skips the cache so we don't have to error the write.
- When we detach, we first try to flush any dirty data (if we were running in
writeback mode). It currently doesn't do anything intelligent if it fails to
read some of the dirty data, though.
TROUBLESHOOTING PERFORMANCE:
Bcache has a bunch of config options and tunables. The defaults are intended to
be reasonable for typical desktop and server workloads, but they're not what you
want for getting the best possible numbers when benchmarking.
- Bad write performance
If write performance is not what you expected, you probably wanted to be
running in writeback mode, which isn't the default (not due to a lack of
maturity, but simply because in writeback mode you'll lose data if something
happens to your SSD)
# echo writeback > /sys/block/bcache0/cache_mode
- Bad performance, or traffic not going to the SSD that you'd expect
By default, bcache doesn't cache everything. It tries to skip sequential IO -
because you really want to be caching the random IO, and if you copy a 10
gigabyte file you probably don't want that pushing 10 gigabytes of randomly
accessed data out of your cache.
But if you want to benchmark reads from cache, and you start out with fio
writing an 8 gigabyte test file - so you want to disable that.
# echo 0 > /sys/block/bcache0/bcache/sequential_cutoff
To set it back to the default (4 mb), do
# echo 4M > /sys/block/bcache0/bcache/sequential_cutoff
- Traffic's still going to the spindle/still getting cache misses
In the real world, SSDs don't always keep up with disks - particularly with
slower SSDs, many disks being cached by one SSD, or mostly sequential IO. So
you want to avoid being bottlenecked by the SSD and having it slow everything
down.
To avoid that bcache tracks latency to the cache device, and gradually
throttles traffic if the latency exceeds a threshold (it does this by
cranking down the sequential bypass).
You can disable this if you need to by setting the thresholds to 0:
# echo 0 > /sys/fs/bcache/<cache set>/congested_read_threshold_us
# echo 0 > /sys/fs/bcache/<cache set>/congested_write_threshold_us
The default is 2000 us (2 milliseconds) for reads, and 20000 for writes.
- Still getting cache misses, of the same data
One last issue that sometimes trips people up is actually an old bug, due to
the way cache coherency is handled for cache misses. If a btree node is full,
a cache miss won't be able to insert a key for the new data and the data
won't be written to the cache.
In practice this isn't an issue because as soon as a write comes along it'll
cause the btree node to be split, and you need almost no write traffic for
this to not show up enough to be noticeable (especially since bcache's btree
nodes are huge and index large regions of the device). But when you're
benchmarking, if you're trying to warm the cache by reading a bunch of data
and there's no other traffic - that can be a problem.
Solution: warm the cache by doing writes, or use the testing branch (there's
a fix for the issue there).
SYSFS - BACKING DEVICE:
Available at /sys/block/<bdev>/bcache, /sys/block/bcache*/bcache and
(if attached) /sys/fs/bcache/<cset-uuid>/bdev*
attach
Echo the UUID of a cache set to this file to enable caching.
cache_mode
Can be one of either writethrough, writeback, writearound or none.
clear_stats
Writing to this file resets the running total stats (not the day/hour/5 minute
decaying versions).
detach
Write to this file to detach from a cache set. If there is dirty data in the
cache, it will be flushed first.
dirty_data
Amount of dirty data for this backing device in the cache. Continuously
updated unlike the cache set's version, but may be slightly off.
label
Name of underlying device.
readahead
Size of readahead that should be performed. Defaults to 0. If set to e.g.
1M, it will round cache miss reads up to that size, but without overlapping
existing cache entries.
running
1 if bcache is running (i.e. whether the /dev/bcache device exists, whether
it's in passthrough mode or caching).
sequential_cutoff
A sequential IO will bypass the cache once it passes this threshold; the
most recent 128 IOs are tracked so sequential IO can be detected even when
it isn't all done at once.
sequential_merge
If non zero, bcache keeps a list of the last 128 requests submitted to compare
against all new requests to determine which new requests are sequential
continuations of previous requests for the purpose of determining sequential
cutoff. This is necessary if the sequential cutoff value is greater than the
maximum acceptable sequential size for any single request.
state
The backing device can be in one of four different states:
no cache: Has never been attached to a cache set.
clean: Part of a cache set, and there is no cached dirty data.
dirty: Part of a cache set, and there is cached dirty data.
inconsistent: The backing device was forcibly run by the user when there was
dirty data cached but the cache set was unavailable; whatever data was on the
backing device has likely been corrupted.
stop
Write to this file to shut down the bcache device and close the backing
device.
writeback_delay
When dirty data is written to the cache and it previously did not contain
any, waits some number of seconds before initiating writeback. Defaults to
30.
writeback_percent
If nonzero, bcache tries to keep around this percentage of the cache dirty by
throttling background writeback and using a PD controller to smoothly adjust
the rate.
writeback_rate
Rate in sectors per second - if writeback_percent is nonzero, background
writeback is throttled to this rate. Continuously adjusted by bcache but may
also be set by the user.
writeback_running
If off, writeback of dirty data will not take place at all. Dirty data will
still be added to the cache until it is mostly full; only meant for
benchmarking. Defaults to on.
SYSFS - BACKING DEVICE STATS:
There are directories with these numbers for a running total, as well as
versions that decay over the past day, hour and 5 minutes; they're also
aggregated in the cache set directory as well.
bypassed
Amount of IO (both reads and writes) that has bypassed the cache
cache_hits
cache_misses
cache_hit_ratio
Hits and misses are counted per individual IO as bcache sees them; a
partial hit is counted as a miss.
cache_bypass_hits
cache_bypass_misses
Hits and misses for IO that is intended to skip the cache are still counted,
but broken out here.
cache_miss_collisions
Counts instances where data was going to be inserted into the cache from a
cache miss, but raced with a write and data was already present (usually 0
since the synchronization for cache misses was rewritten)
cache_readaheads
Count of times readahead occurred.
SYSFS - CACHE SET:
Available at /sys/fs/bcache/<cset-uuid>
average_key_size
Average data per key in the btree.
bdev<0..n>
Symlink to each of the attached backing devices.
block_size
Block size of the cache devices.
btree_cache_size
Amount of memory currently used by the btree cache
bucket_size
Size of buckets
cache<0..n>
Symlink to each of the cache devices comprising this cache set.
cache_available_percent
Percentage of cache device which doesn't contain dirty data, and could
potentially be used for writeback. This doesn't mean this space isn't used
for clean cached data; the unused statistic (in priority_stats) is typically
much lower.
clear_stats
Clears the statistics associated with this cache
dirty_data
Amount of dirty data is in the cache (updated when garbage collection runs).
flash_vol_create
Echoing a size to this file (in human readable units, k/M/G) creates a thinly
provisioned volume backed by the cache set.
io_error_halflife
io_error_limit
These determines how many errors we accept before disabling the cache.
Each error is decayed by the half life (in # ios). If the decaying count
reaches io_error_limit dirty data is written out and the cache is disabled.
journal_delay_ms
Journal writes will delay for up to this many milliseconds, unless a cache
flush happens sooner. Defaults to 100.
root_usage_percent
Percentage of the root btree node in use. If this gets too high the node
will split, increasing the tree depth.
stop
Write to this file to shut down the cache set - waits until all attached
backing devices have been shut down.
tree_depth
Depth of the btree (A single node btree has depth 0).
unregister
Detaches all backing devices and closes the cache devices; if dirty data is
present it will disable writeback caching and wait for it to be flushed.
SYSFS - CACHE SET INTERNAL:
This directory also exposes timings for a number of internal operations, with
separate files for average duration, average frequency, last occurrence and max
duration: garbage collection, btree read, btree node sorts and btree splits.
active_journal_entries
Number of journal entries that are newer than the index.
btree_nodes
Total nodes in the btree.
btree_used_percent
Average fraction of btree in use.
bset_tree_stats
Statistics about the auxiliary search trees
btree_cache_max_chain
Longest chain in the btree node cache's hash table
cache_read_races
Counts instances where while data was being read from the cache, the bucket
was reused and invalidated - i.e. where the pointer was stale after the read
completed. When this occurs the data is reread from the backing device.
trigger_gc
Writing to this file forces garbage collection to run.
SYSFS - CACHE DEVICE:
Available at /sys/block/<cdev>/bcache
block_size
Minimum granularity of writes - should match hardware sector size.
btree_written
Sum of all btree writes, in (kilo/mega/giga) bytes
bucket_size
Size of buckets
cache_replacement_policy
One of either lru, fifo or random.
discard
Boolean; if on a discard/TRIM will be issued to each bucket before it is
reused. Defaults to off, since SATA TRIM is an unqueued command (and thus
slow).
freelist_percent
Size of the freelist as a percentage of nbuckets. Can be written to to
increase the number of buckets kept on the freelist, which lets you
artificially reduce the size of the cache at runtime. Mostly for testing
purposes (i.e. testing how different size caches affect your hit rate), but
since buckets are discarded when they move on to the freelist will also make
the SSD's garbage collection easier by effectively giving it more reserved
space.
io_errors
Number of errors that have occurred, decayed by io_error_halflife.
metadata_written
Sum of all non data writes (btree writes and all other metadata).
nbuckets
Total buckets in this cache
priority_stats
Statistics about how recently data in the cache has been accessed.
This can reveal your working set size. Unused is the percentage of
the cache that doesn't contain any data. Metadata is bcache's
metadata overhead. Average is the average priority of cache buckets.
Next is a list of quantiles with the priority threshold of each.
written
Sum of all data that has been written to the cache; comparison with
btree_written gives the amount of write inflation in bcache.