swh:1:snp:173f8deb0c56c557784b4fd217e7608ac6197844
Tip revision: 9123e3a74ec7b934a4a099e98af6a61c2f80bbf5 authored by Linus Torvalds on 16 August 2020, 20:04:57 UTC
Linux 5.9-rc1
Linux 5.9-rc1
Tip revision: 9123e3a
atusb.h
/* SPDX-License-Identifier: GPL-2.0-only */
/*
* atusb.h - Definitions shared between kernel and ATUSB firmware
*
* Written 2013 by Werner Almesberger <werner@almesberger.net>
*
* (at your option) any later version.
*
* This file should be identical for kernel and firmware.
* Kernel: drivers/net/ieee802154/atusb.h
* Firmware: ben-wpan/atusb/fw/include/atusb/atusb.h
*/
#ifndef _ATUSB_H
#define _ATUSB_H
#define ATUSB_VENDOR_ID 0x20b7 /* Qi Hardware*/
#define ATUSB_PRODUCT_ID 0x1540 /* 802.15.4, device 0 */
/* -- - - */
#define ATUSB_BUILD_SIZE 256 /* maximum build version/date message length */
/* Commands to our device. Make sure this is synced with the firmware */
enum atusb_requests {
ATUSB_ID = 0x00, /* system status/control grp */
ATUSB_BUILD,
ATUSB_RESET,
ATUSB_RF_RESET = 0x10, /* debug/test group */
ATUSB_POLL_INT,
ATUSB_TEST, /* atusb-sil only */
ATUSB_TIMER,
ATUSB_GPIO,
ATUSB_SLP_TR,
ATUSB_GPIO_CLEANUP,
ATUSB_REG_WRITE = 0x20, /* transceiver group */
ATUSB_REG_READ,
ATUSB_BUF_WRITE,
ATUSB_BUF_READ,
ATUSB_SRAM_WRITE,
ATUSB_SRAM_READ,
ATUSB_SPI_WRITE = 0x30, /* SPI group */
ATUSB_SPI_READ1,
ATUSB_SPI_READ2,
ATUSB_SPI_WRITE2_SYNC,
ATUSB_RX_MODE = 0x40, /* HardMAC group */
ATUSB_TX,
ATUSB_EUI64_WRITE = 0x50, /* Parameter in EEPROM grp */
ATUSB_EUI64_READ,
};
enum {
ATUSB_HW_TYPE_100813, /* 2010-08-13 */
ATUSB_HW_TYPE_101216, /* 2010-12-16 */
ATUSB_HW_TYPE_110131, /* 2011-01-31, ATmega32U2-based */
ATUSB_HW_TYPE_RZUSB, /* Atmel Raven USB dongle with at86rf230 */
ATUSB_HW_TYPE_HULUSB, /* Busware HUL USB dongle with at86rf212 */
};
/*
* Direction bRequest wValue wIndex wLength
*
* ->host ATUSB_ID - - 3
* ->host ATUSB_BUILD - - #bytes
* host-> ATUSB_RESET - - 0
*
* host-> ATUSB_RF_RESET - - 0
* ->host ATUSB_POLL_INT - - 1
* host-> ATUSB_TEST - - 0
* ->host ATUSB_TIMER - - #bytes (6)
* ->host ATUSB_GPIO dir+data mask+p# 3
* host-> ATUSB_SLP_TR - - 0
* host-> ATUSB_GPIO_CLEANUP - - 0
*
* host-> ATUSB_REG_WRITE value addr 0
* ->host ATUSB_REG_READ - addr 1
* host-> ATUSB_BUF_WRITE - - #bytes
* ->host ATUSB_BUF_READ - - #bytes
* host-> ATUSB_SRAM_WRITE - addr #bytes
* ->host ATUSB_SRAM_READ - addr #bytes
*
* host-> ATUSB_SPI_WRITE byte0 byte1 #bytes
* ->host ATUSB_SPI_READ1 byte0 - #bytes
* ->host ATUSB_SPI_READ2 byte0 byte1 #bytes
* ->host ATUSB_SPI_WRITE2_SYNC byte0 byte1 0/1
*
* host-> ATUSB_RX_MODE on - 0
* host-> ATUSB_TX flags ack_seq #bytes
* host-> ATUSB_EUI64_WRITE - - #bytes (8)
* ->host ATUSB_EUI64_READ - - #bytes (8)
*/
#define ATUSB_REQ_FROM_DEV (USB_TYPE_VENDOR | USB_DIR_IN)
#define ATUSB_REQ_TO_DEV (USB_TYPE_VENDOR | USB_DIR_OUT)
#endif /* !_ATUSB_H */