swh:1:snp:173f8deb0c56c557784b4fd217e7608ac6197844
Tip revision: e44a21b7268a022c7749f521c06214145bd161e4 authored by Linus Torvalds on 06 June 2010, 03:43:24 UTC
Linux 2.6.35-rc2
Linux 2.6.35-rc2
Tip revision: e44a21b
r819xE_phy.c
#include "r8192E.h"
#include "r8192E_hw.h"
#include "r819xE_phyreg.h"
#include "r8190_rtl8256.h"
#include "r819xE_phy.h"
#include "r8192E_dm.h"
#ifdef ENABLE_DOT11D
#include "ieee80211/dot11d.h"
#endif
static u32 RF_CHANNEL_TABLE_ZEBRA[] = {
0,
0x085c, //2412 1
0x08dc, //2417 2
0x095c, //2422 3
0x09dc, //2427 4
0x0a5c, //2432 5
0x0adc, //2437 6
0x0b5c, //2442 7
0x0bdc, //2447 8
0x0c5c, //2452 9
0x0cdc, //2457 10
0x0d5c, //2462 11
0x0ddc, //2467 12
0x0e5c, //2472 13
0x0f72, //2484
};
#ifdef RTL8190P
u32 Rtl8190PciMACPHY_Array[] = {
0x03c,0xffff0000,0x00000f0f,
0x340,0xffffffff,0x161a1a1a,
0x344,0xffffffff,0x12121416,
0x348,0x0000ffff,0x00001818,
0x12c,0xffffffff,0x04000802,
0x318,0x00000fff,0x00000800,
};
u32 Rtl8190PciMACPHY_Array_PG[] = {
0x03c,0xffff0000,0x00000f0f,
0x340,0xffffffff,0x0a0c0d0f,
0x344,0xffffffff,0x06070809,
0x344,0xffffffff,0x06070809,
0x348,0x0000ffff,0x00000000,
0x12c,0xffffffff,0x04000802,
0x318,0x00000fff,0x00000800,
};
u32 Rtl8190PciAGCTAB_Array[AGCTAB_ArrayLength] = {
0xc78,0x7d000001,
0xc78,0x7d010001,
0xc78,0x7d020001,
0xc78,0x7d030001,
0xc78,0x7c040001,
0xc78,0x7b050001,
0xc78,0x7a060001,
0xc78,0x79070001,
0xc78,0x78080001,
0xc78,0x77090001,
0xc78,0x760a0001,
0xc78,0x750b0001,
0xc78,0x740c0001,
0xc78,0x730d0001,
0xc78,0x720e0001,
0xc78,0x710f0001,
0xc78,0x70100001,
0xc78,0x6f110001,
0xc78,0x6e120001,
0xc78,0x6d130001,
0xc78,0x6c140001,
0xc78,0x6b150001,
0xc78,0x6a160001,
0xc78,0x69170001,
0xc78,0x68180001,
0xc78,0x67190001,
0xc78,0x661a0001,
0xc78,0x651b0001,
0xc78,0x641c0001,
0xc78,0x491d0001,
0xc78,0x481e0001,
0xc78,0x471f0001,
0xc78,0x46200001,
0xc78,0x45210001,
0xc78,0x44220001,
0xc78,0x43230001,
0xc78,0x28240001,
0xc78,0x27250001,
0xc78,0x26260001,
0xc78,0x25270001,
0xc78,0x24280001,
0xc78,0x23290001,
0xc78,0x222a0001,
0xc78,0x212b0001,
0xc78,0x202c0001,
0xc78,0x0a2d0001,
0xc78,0x082e0001,
0xc78,0x062f0001,
0xc78,0x05300001,
0xc78,0x04310001,
0xc78,0x03320001,
0xc78,0x02330001,
0xc78,0x01340001,
0xc78,0x00350001,
0xc78,0x00360001,
0xc78,0x00370001,
0xc78,0x00380001,
0xc78,0x00390001,
0xc78,0x003a0001,
0xc78,0x003b0001,
0xc78,0x003c0001,
0xc78,0x003d0001,
0xc78,0x003e0001,
0xc78,0x003f0001,
0xc78,0x7d400001,
0xc78,0x7d410001,
0xc78,0x7d420001,
0xc78,0x7d430001,
0xc78,0x7c440001,
0xc78,0x7b450001,
0xc78,0x7a460001,
0xc78,0x79470001,
0xc78,0x78480001,
0xc78,0x77490001,
0xc78,0x764a0001,
0xc78,0x754b0001,
0xc78,0x744c0001,
0xc78,0x734d0001,
0xc78,0x724e0001,
0xc78,0x714f0001,
0xc78,0x70500001,
0xc78,0x6f510001,
0xc78,0x6e520001,
0xc78,0x6d530001,
0xc78,0x6c540001,
0xc78,0x6b550001,
0xc78,0x6a560001,
0xc78,0x69570001,
0xc78,0x68580001,
0xc78,0x67590001,
0xc78,0x665a0001,
0xc78,0x655b0001,
0xc78,0x645c0001,
0xc78,0x495d0001,
0xc78,0x485e0001,
0xc78,0x475f0001,
0xc78,0x46600001,
0xc78,0x45610001,
0xc78,0x44620001,
0xc78,0x43630001,
0xc78,0x28640001,
0xc78,0x27650001,
0xc78,0x26660001,
0xc78,0x25670001,
0xc78,0x24680001,
0xc78,0x23690001,
0xc78,0x226a0001,
0xc78,0x216b0001,
0xc78,0x206c0001,
0xc78,0x0a6d0001,
0xc78,0x086e0001,
0xc78,0x066f0001,
0xc78,0x05700001,
0xc78,0x04710001,
0xc78,0x03720001,
0xc78,0x02730001,
0xc78,0x01740001,
0xc78,0x00750001,
0xc78,0x00760001,
0xc78,0x00770001,
0xc78,0x00780001,
0xc78,0x00790001,
0xc78,0x007a0001,
0xc78,0x007b0001,
0xc78,0x007c0001,
0xc78,0x007d0001,
0xc78,0x007e0001,
0xc78,0x007f0001,
0xc78,0x3600001e,
0xc78,0x3601001e,
0xc78,0x3602001e,
0xc78,0x3603001e,
0xc78,0x3604001e,
0xc78,0x3605001e,
0xc78,0x3a06001e,
0xc78,0x3c07001e,
0xc78,0x3e08001e,
0xc78,0x4209001e,
0xc78,0x430a001e,
0xc78,0x450b001e,
0xc78,0x470c001e,
0xc78,0x480d001e,
0xc78,0x490e001e,
0xc78,0x4b0f001e,
0xc78,0x4c10001e,
0xc78,0x4d11001e,
0xc78,0x4d12001e,
0xc78,0x4e13001e,
0xc78,0x4f14001e,
0xc78,0x5015001e,
0xc78,0x5116001e,
0xc78,0x5117001e,
0xc78,0x5218001e,
0xc78,0x5219001e,
0xc78,0x531a001e,
0xc78,0x541b001e,
0xc78,0x541c001e,
0xc78,0x551d001e,
0xc78,0x561e001e,
0xc78,0x561f001e,
0xc78,0x5720001e,
0xc78,0x5821001e,
0xc78,0x5822001e,
0xc78,0x5923001e,
0xc78,0x5924001e,
0xc78,0x5a25001e,
0xc78,0x5b26001e,
0xc78,0x5b27001e,
0xc78,0x5c28001e,
0xc78,0x5c29001e,
0xc78,0x5d2a001e,
0xc78,0x5d2b001e,
0xc78,0x5e2c001e,
0xc78,0x5e2d001e,
0xc78,0x5f2e001e,
0xc78,0x602f001e,
0xc78,0x6030001e,
0xc78,0x6131001e,
0xc78,0x6132001e,
0xc78,0x6233001e,
0xc78,0x6234001e,
0xc78,0x6335001e,
0xc78,0x6336001e,
0xc78,0x6437001e,
0xc78,0x6538001e,
0xc78,0x6639001e,
0xc78,0x663a001e,
0xc78,0x673b001e,
0xc78,0x683c001e,
0xc78,0x693d001e,
0xc78,0x6a3e001e,
0xc78,0x6b3f001e,
};
u32 Rtl8190PciPHY_REGArray[PHY_REGArrayLength] = {
0x800,0x00050060,
0x804,0x00000005,
0x808,0x0000fc00,
0x80c,0x0000001c,
0x810,0x801010aa,
0x814,0x000908c0,
0x818,0x00000000,
0x81c,0x00000000,
0x820,0x00000004,
0x824,0x00690000,
0x828,0x00000004,
0x82c,0x00e90000,
0x830,0x00000004,
0x834,0x00690000,
0x838,0x00000004,
0x83c,0x00e90000,
0x840,0x00000000,
0x844,0x00000000,
0x848,0x00000000,
0x84c,0x00000000,
0x850,0x00000000,
0x854,0x00000000,
0x858,0x65a965a9,
0x85c,0x65a965a9,
0x860,0x001f0010,
0x864,0x007f0010,
0x868,0x001f0010,
0x86c,0x007f0010,
0x870,0x0f100f70,
0x874,0x0f100f70,
0x878,0x00000000,
0x87c,0x00000000,
0x880,0x5c385eb8,
0x884,0x6357060d,
0x888,0x0460c341,
0x88c,0x0000ff00,
0x890,0x00000000,
0x894,0xfffffffe,
0x898,0x4c42382f,
0x89c,0x00656056,
0x8b0,0x00000000,
0x8e0,0x00000000,
0x8e4,0x00000000,
0x900,0x00000000,
0x904,0x00000023,
0x908,0x00000000,
0x90c,0x35541545,
0xa00,0x00d0c7d8,
0xa04,0xab1f0008,
0xa08,0x80cd8300,
0xa0c,0x2e62740f,
0xa10,0x95009b78,
0xa14,0x11145008,
0xa18,0x00881117,
0xa1c,0x89140fa0,
0xa20,0x1a1b0000,
0xa24,0x090e1317,
0xa28,0x00000204,
0xa2c,0x00000000,
0xc00,0x00000040,
0xc04,0x0000500f,
0xc08,0x000000e4,
0xc0c,0x6c6c6c6c,
0xc10,0x08000000,
0xc14,0x40000100,
0xc18,0x08000000,
0xc1c,0x40000100,
0xc20,0x08000000,
0xc24,0x40000100,
0xc28,0x08000000,
0xc2c,0x40000100,
0xc30,0x6de9ac44,
0xc34,0x164052cd,
0xc38,0x00070a14,
0xc3c,0x0a969764,
0xc40,0x1f7c403f,
0xc44,0x000100b7,
0xc48,0xec020000,
0xc4c,0x00000300,
0xc50,0x69543420,
0xc54,0x433c0094,
0xc58,0x69543420,
0xc5c,0x433c0094,
0xc60,0x69543420,
0xc64,0x433c0094,
0xc68,0x69543420,
0xc6c,0x433c0094,
0xc70,0x2c7f000d,
0xc74,0x0186175b,
0xc78,0x0000001f,
0xc7c,0x00b91612,
0xc80,0x40000100,
0xc84,0x00000000,
0xc88,0x40000100,
0xc8c,0x08000000,
0xc90,0x40000100,
0xc94,0x00000000,
0xc98,0x40000100,
0xc9c,0x00000000,
0xca0,0x00492492,
0xca4,0x00000000,
0xca8,0x00000000,
0xcac,0x00000000,
0xcb0,0x00000000,
0xcb4,0x00000000,
0xcb8,0x00000000,
0xcbc,0x00492492,
0xcc0,0x00000000,
0xcc4,0x00000000,
0xcc8,0x00000000,
0xccc,0x00000000,
0xcd0,0x00000000,
0xcd4,0x00000000,
0xcd8,0x64b22427,
0xcdc,0x00766932,
0xce0,0x00222222,
0xd00,0x00000740,
0xd04,0x0000040f,
0xd08,0x0000803f,
0xd0c,0x00000001,
0xd10,0xa0633333,
0xd14,0x33333c63,
0xd18,0x6a8f5b6b,
0xd1c,0x00000000,
0xd20,0x00000000,
0xd24,0x00000000,
0xd28,0x00000000,
0xd2c,0xcc979975,
0xd30,0x00000000,
0xd34,0x00000000,
0xd38,0x00000000,
0xd3c,0x00027293,
0xd40,0x00000000,
0xd44,0x00000000,
0xd48,0x00000000,
0xd4c,0x00000000,
0xd50,0x6437140a,
0xd54,0x024dbd02,
0xd58,0x00000000,
0xd5c,0x14032064,
};
u32 Rtl8190PciPHY_REG_1T2RArray[PHY_REG_1T2RArrayLength] = {
0x800,0x00050060,
0x804,0x00000004,
0x808,0x0000fc00,
0x80c,0x0000001c,
0x810,0x801010aa,
0x814,0x000908c0,
0x818,0x00000000,
0x81c,0x00000000,
0x820,0x00000004,
0x824,0x00690000,
0x828,0x00000004,
0x82c,0x00e90000,
0x830,0x00000004,
0x834,0x00690000,
0x838,0x00000004,
0x83c,0x00e90000,
0x840,0x00000000,
0x844,0x00000000,
0x848,0x00000000,
0x84c,0x00000000,
0x850,0x00000000,
0x854,0x00000000,
0x858,0x65a965a9,
0x85c,0x65a965a9,
0x860,0x001f0000,
0x864,0x007f0000,
0x868,0x001f0010,
0x86c,0x007f0010,
0x870,0x0f100f70,
0x874,0x0f100f70,
0x878,0x00000000,
0x87c,0x00000000,
0x880,0x5c385898,
0x884,0x6357060d,
0x888,0x0460c341,
0x88c,0x0000fc00,
0x890,0x00000000,
0x894,0xfffffffe,
0x898,0x4c42382f,
0x89c,0x00656056,
0x8b0,0x00000000,
0x8e0,0x00000000,
0x8e4,0x00000000,
0x900,0x00000000,
0x904,0x00000023,
0x908,0x00000000,
0x90c,0x34441444,
0xa00,0x00d0c7d8,
0xa04,0x2b1f0008,
0xa08,0x80cd8300,
0xa0c,0x2e62740f,
0xa10,0x95009b78,
0xa14,0x11145008,
0xa18,0x00881117,
0xa1c,0x89140fa0,
0xa20,0x1a1b0000,
0xa24,0x090e1317,
0xa28,0x00000204,
0xa2c,0x00000000,
0xc00,0x00000040,
0xc04,0x0000500c,
0xc08,0x000000e4,
0xc0c,0x6c6c6c6c,
0xc10,0x08000000,
0xc14,0x40000100,
0xc18,0x08000000,
0xc1c,0x40000100,
0xc20,0x08000000,
0xc24,0x40000100,
0xc28,0x08000000,
0xc2c,0x40000100,
0xc30,0x6de9ac44,
0xc34,0x164052cd,
0xc38,0x00070a14,
0xc3c,0x0a969764,
0xc40,0x1f7c403f,
0xc44,0x000100b7,
0xc48,0xec020000,
0xc4c,0x00000300,
0xc50,0x69543420,
0xc54,0x433c0094,
0xc58,0x69543420,
0xc5c,0x433c0094,
0xc60,0x69543420,
0xc64,0x433c0094,
0xc68,0x69543420,
0xc6c,0x433c0094,
0xc70,0x2c7f000d,
0xc74,0x0186175b,
0xc78,0x0000001f,
0xc7c,0x00b91612,
0xc80,0x40000100,
0xc84,0x00000000,
0xc88,0x40000100,
0xc8c,0x08000000,
0xc90,0x40000100,
0xc94,0x00000000,
0xc98,0x40000100,
0xc9c,0x00000000,
0xca0,0x00492492,
0xca4,0x00000000,
0xca8,0x00000000,
0xcac,0x00000000,
0xcb0,0x00000000,
0xcb4,0x00000000,
0xcb8,0x00000000,
0xcbc,0x00492492,
0xcc0,0x00000000,
0xcc4,0x00000000,
0xcc8,0x00000000,
0xccc,0x00000000,
0xcd0,0x00000000,
0xcd4,0x00000000,
0xcd8,0x64b22427,
0xcdc,0x00766932,
0xce0,0x00222222,
0xd00,0x00000740,
0xd04,0x0000040c,
0xd08,0x0000803f,
0xd0c,0x00000001,
0xd10,0xa0633333,
0xd14,0x33333c63,
0xd18,0x6a8f5b6b,
0xd1c,0x00000000,
0xd20,0x00000000,
0xd24,0x00000000,
0xd28,0x00000000,
0xd2c,0xcc979975,
0xd30,0x00000000,
0xd34,0x00000000,
0xd38,0x00000000,
0xd3c,0x00027293,
0xd40,0x00000000,
0xd44,0x00000000,
0xd48,0x00000000,
0xd4c,0x00000000,
0xd50,0x6437140a,
0xd54,0x024dbd02,
0xd58,0x00000000,
0xd5c,0x14032064,
};
u32 Rtl8190PciRadioA_Array[RadioA_ArrayLength] = {
0x019,0x00000003,
0x000,0x000000bf,
0x001,0x00000ee0,
0x002,0x0000004c,
0x003,0x000007f1,
0x004,0x00000975,
0x005,0x00000c58,
0x006,0x00000ae6,
0x007,0x000000ca,
0x008,0x00000e1c,
0x009,0x000007f0,
0x00a,0x000009d0,
0x00b,0x000001ba,
0x00c,0x00000240,
0x00e,0x00000020,
0x00f,0x00000990,
0x012,0x00000806,
0x014,0x000005ab,
0x015,0x00000f80,
0x016,0x00000020,
0x017,0x00000597,
0x018,0x0000050a,
0x01a,0x00000f80,
0x01b,0x00000f5e,
0x01c,0x00000008,
0x01d,0x00000607,
0x01e,0x000006cc,
0x01f,0x00000000,
0x020,0x000001a5,
0x01f,0x00000001,
0x020,0x00000165,
0x01f,0x00000002,
0x020,0x000000c6,
0x01f,0x00000003,
0x020,0x00000086,
0x01f,0x00000004,
0x020,0x00000046,
0x01f,0x00000005,
0x020,0x000001e6,
0x01f,0x00000006,
0x020,0x000001a6,
0x01f,0x00000007,
0x020,0x00000166,
0x01f,0x00000008,
0x020,0x000000c7,
0x01f,0x00000009,
0x020,0x00000087,
0x01f,0x0000000a,
0x020,0x000000f7,
0x01f,0x0000000b,
0x020,0x000000d7,
0x01f,0x0000000c,
0x020,0x000000b7,
0x01f,0x0000000d,
0x020,0x00000097,
0x01f,0x0000000e,
0x020,0x00000077,
0x01f,0x0000000f,
0x020,0x00000057,
0x01f,0x00000010,
0x020,0x00000037,
0x01f,0x00000011,
0x020,0x000000fb,
0x01f,0x00000012,
0x020,0x000000db,
0x01f,0x00000013,
0x020,0x000000bb,
0x01f,0x00000014,
0x020,0x000000ff,
0x01f,0x00000015,
0x020,0x000000e3,
0x01f,0x00000016,
0x020,0x000000c3,
0x01f,0x00000017,
0x020,0x000000a3,
0x01f,0x00000018,
0x020,0x00000083,
0x01f,0x00000019,
0x020,0x00000063,
0x01f,0x0000001a,
0x020,0x00000043,
0x01f,0x0000001b,
0x020,0x00000023,
0x01f,0x0000001c,
0x020,0x00000003,
0x01f,0x0000001d,
0x020,0x000001e3,
0x01f,0x0000001e,
0x020,0x000001c3,
0x01f,0x0000001f,
0x020,0x000001a3,
0x01f,0x00000020,
0x020,0x00000183,
0x01f,0x00000021,
0x020,0x00000163,
0x01f,0x00000022,
0x020,0x00000143,
0x01f,0x00000023,
0x020,0x00000123,
0x01f,0x00000024,
0x020,0x00000103,
0x023,0x00000203,
0x024,0x00000200,
0x00b,0x000001ba,
0x02c,0x000003d7,
0x02d,0x00000ff0,
0x000,0x00000037,
0x004,0x00000160,
0x007,0x00000080,
0x002,0x0000088d,
0x0fe,0x00000000,
0x0fe,0x00000000,
0x016,0x00000200,
0x016,0x00000380,
0x016,0x00000020,
0x016,0x000001a0,
0x000,0x000000bf,
0x00d,0x0000001f,
0x00d,0x00000c9f,
0x002,0x0000004d,
0x000,0x00000cbf,
0x004,0x00000975,
0x007,0x00000700,
};
u32 Rtl8190PciRadioB_Array[RadioB_ArrayLength] = {
0x019,0x00000003,
0x000,0x000000bf,
0x001,0x000006e0,
0x002,0x0000004c,
0x003,0x000007f1,
0x004,0x00000975,
0x005,0x00000c58,
0x006,0x00000ae6,
0x007,0x000000ca,
0x008,0x00000e1c,
0x000,0x000000b7,
0x00a,0x00000850,
0x000,0x000000bf,
0x00b,0x000001ba,
0x00c,0x00000240,
0x00e,0x00000020,
0x015,0x00000f80,
0x016,0x00000020,
0x017,0x00000597,
0x018,0x0000050a,
0x01a,0x00000e00,
0x01b,0x00000f5e,
0x01d,0x00000607,
0x01e,0x000006cc,
0x00b,0x000001ba,
0x023,0x00000203,
0x024,0x00000200,
0x000,0x00000037,
0x004,0x00000160,
0x016,0x00000200,
0x016,0x00000380,
0x016,0x00000020,
0x016,0x000001a0,
0x00d,0x00000ccc,
0x000,0x000000bf,
0x002,0x0000004d,
0x000,0x00000cbf,
0x004,0x00000975,
0x007,0x00000700,
};
u32 Rtl8190PciRadioC_Array[RadioC_ArrayLength] = {
0x019,0x00000003,
0x000,0x000000bf,
0x001,0x00000ee0,
0x002,0x0000004c,
0x003,0x000007f1,
0x004,0x00000975,
0x005,0x00000c58,
0x006,0x00000ae6,
0x007,0x000000ca,
0x008,0x00000e1c,
0x009,0x000007f0,
0x00a,0x000009d0,
0x00b,0x000001ba,
0x00c,0x00000240,
0x00e,0x00000020,
0x00f,0x00000990,
0x012,0x00000806,
0x014,0x000005ab,
0x015,0x00000f80,
0x016,0x00000020,
0x017,0x00000597,
0x018,0x0000050a,
0x01a,0x00000f80,
0x01b,0x00000f5e,
0x01c,0x00000008,
0x01d,0x00000607,
0x01e,0x000006cc,
0x01f,0x00000000,
0x020,0x000001a5,
0x01f,0x00000001,
0x020,0x00000165,
0x01f,0x00000002,
0x020,0x000000c6,
0x01f,0x00000003,
0x020,0x00000086,
0x01f,0x00000004,
0x020,0x00000046,
0x01f,0x00000005,
0x020,0x000001e6,
0x01f,0x00000006,
0x020,0x000001a6,
0x01f,0x00000007,
0x020,0x00000166,
0x01f,0x00000008,
0x020,0x000000c7,
0x01f,0x00000009,
0x020,0x00000087,
0x01f,0x0000000a,
0x020,0x000000f7,
0x01f,0x0000000b,
0x020,0x000000d7,
0x01f,0x0000000c,
0x020,0x000000b7,
0x01f,0x0000000d,
0x020,0x00000097,
0x01f,0x0000000e,
0x020,0x00000077,
0x01f,0x0000000f,
0x020,0x00000057,
0x01f,0x00000010,
0x020,0x00000037,
0x01f,0x00000011,
0x020,0x000000fb,
0x01f,0x00000012,
0x020,0x000000db,
0x01f,0x00000013,
0x020,0x000000bb,
0x01f,0x00000014,
0x020,0x000000ff,
0x01f,0x00000015,
0x020,0x000000e3,
0x01f,0x00000016,
0x020,0x000000c3,
0x01f,0x00000017,
0x020,0x000000a3,
0x01f,0x00000018,
0x020,0x00000083,
0x01f,0x00000019,
0x020,0x00000063,
0x01f,0x0000001a,
0x020,0x00000043,
0x01f,0x0000001b,
0x020,0x00000023,
0x01f,0x0000001c,
0x020,0x00000003,
0x01f,0x0000001d,
0x020,0x000001e3,
0x01f,0x0000001e,
0x020,0x000001c3,
0x01f,0x0000001f,
0x020,0x000001a3,
0x01f,0x00000020,
0x020,0x00000183,
0x01f,0x00000021,
0x020,0x00000163,
0x01f,0x00000022,
0x020,0x00000143,
0x01f,0x00000023,
0x020,0x00000123,
0x01f,0x00000024,
0x020,0x00000103,
0x023,0x00000203,
0x024,0x00000200,
0x00b,0x000001ba,
0x02c,0x000003d7,
0x02d,0x00000ff0,
0x000,0x00000037,
0x004,0x00000160,
0x007,0x00000080,
0x002,0x0000088d,
0x0fe,0x00000000,
0x0fe,0x00000000,
0x016,0x00000200,
0x016,0x00000380,
0x016,0x00000020,
0x016,0x000001a0,
0x000,0x000000bf,
0x00d,0x0000001f,
0x00d,0x00000c9f,
0x002,0x0000004d,
0x000,0x00000cbf,
0x004,0x00000975,
0x007,0x00000700,
};
u32 Rtl8190PciRadioD_Array[RadioD_ArrayLength] = {
0x019,0x00000003,
0x000,0x000000bf,
0x001,0x000006e0,
0x002,0x0000004c,
0x003,0x000007f1,
0x004,0x00000975,
0x005,0x00000c58,
0x006,0x00000ae6,
0x007,0x000000ca,
0x008,0x00000e1c,
0x000,0x000000b7,
0x00a,0x00000850,
0x000,0x000000bf,
0x00b,0x000001ba,
0x00c,0x00000240,
0x00e,0x00000020,
0x015,0x00000f80,
0x016,0x00000020,
0x017,0x00000597,
0x018,0x0000050a,
0x01a,0x00000e00,
0x01b,0x00000f5e,
0x01d,0x00000607,
0x01e,0x000006cc,
0x00b,0x000001ba,
0x023,0x00000203,
0x024,0x00000200,
0x000,0x00000037,
0x004,0x00000160,
0x016,0x00000200,
0x016,0x00000380,
0x016,0x00000020,
0x016,0x000001a0,
0x00d,0x00000ccc,
0x000,0x000000bf,
0x002,0x0000004d,
0x000,0x00000cbf,
0x004,0x00000975,
0x007,0x00000700,
};
#endif
#ifdef RTL8192E
static u32 Rtl8192PciEMACPHY_Array[] = {
0x03c,0xffff0000,0x00000f0f,
0x340,0xffffffff,0x161a1a1a,
0x344,0xffffffff,0x12121416,
0x348,0x0000ffff,0x00001818,
0x12c,0xffffffff,0x04000802,
0x318,0x00000fff,0x00000100,
};
static u32 Rtl8192PciEMACPHY_Array_PG[] = {
0x03c,0xffff0000,0x00000f0f,
0xe00,0xffffffff,0x06090909,
0xe04,0xffffffff,0x00030306,
0xe08,0x0000ff00,0x00000000,
0xe10,0xffffffff,0x0a0c0d0f,
0xe14,0xffffffff,0x06070809,
0xe18,0xffffffff,0x0a0c0d0f,
0xe1c,0xffffffff,0x06070809,
0x12c,0xffffffff,0x04000802,
0x318,0x00000fff,0x00000800,
};
static u32 Rtl8192PciEAGCTAB_Array[AGCTAB_ArrayLength] = {
0xc78,0x7d000001,
0xc78,0x7d010001,
0xc78,0x7d020001,
0xc78,0x7d030001,
0xc78,0x7d040001,
0xc78,0x7d050001,
0xc78,0x7c060001,
0xc78,0x7b070001,
0xc78,0x7a080001,
0xc78,0x79090001,
0xc78,0x780a0001,
0xc78,0x770b0001,
0xc78,0x760c0001,
0xc78,0x750d0001,
0xc78,0x740e0001,
0xc78,0x730f0001,
0xc78,0x72100001,
0xc78,0x71110001,
0xc78,0x70120001,
0xc78,0x6f130001,
0xc78,0x6e140001,
0xc78,0x6d150001,
0xc78,0x6c160001,
0xc78,0x6b170001,
0xc78,0x6a180001,
0xc78,0x69190001,
0xc78,0x681a0001,
0xc78,0x671b0001,
0xc78,0x661c0001,
0xc78,0x651d0001,
0xc78,0x641e0001,
0xc78,0x491f0001,
0xc78,0x48200001,
0xc78,0x47210001,
0xc78,0x46220001,
0xc78,0x45230001,
0xc78,0x44240001,
0xc78,0x43250001,
0xc78,0x28260001,
0xc78,0x27270001,
0xc78,0x26280001,
0xc78,0x25290001,
0xc78,0x242a0001,
0xc78,0x232b0001,
0xc78,0x222c0001,
0xc78,0x212d0001,
0xc78,0x202e0001,
0xc78,0x0a2f0001,
0xc78,0x08300001,
0xc78,0x06310001,
0xc78,0x05320001,
0xc78,0x04330001,
0xc78,0x03340001,
0xc78,0x02350001,
0xc78,0x01360001,
0xc78,0x00370001,
0xc78,0x00380001,
0xc78,0x00390001,
0xc78,0x003a0001,
0xc78,0x003b0001,
0xc78,0x003c0001,
0xc78,0x003d0001,
0xc78,0x003e0001,
0xc78,0x003f0001,
0xc78,0x7d400001,
0xc78,0x7d410001,
0xc78,0x7d420001,
0xc78,0x7d430001,
0xc78,0x7d440001,
0xc78,0x7d450001,
0xc78,0x7c460001,
0xc78,0x7b470001,
0xc78,0x7a480001,
0xc78,0x79490001,
0xc78,0x784a0001,
0xc78,0x774b0001,
0xc78,0x764c0001,
0xc78,0x754d0001,
0xc78,0x744e0001,
0xc78,0x734f0001,
0xc78,0x72500001,
0xc78,0x71510001,
0xc78,0x70520001,
0xc78,0x6f530001,
0xc78,0x6e540001,
0xc78,0x6d550001,
0xc78,0x6c560001,
0xc78,0x6b570001,
0xc78,0x6a580001,
0xc78,0x69590001,
0xc78,0x685a0001,
0xc78,0x675b0001,
0xc78,0x665c0001,
0xc78,0x655d0001,
0xc78,0x645e0001,
0xc78,0x495f0001,
0xc78,0x48600001,
0xc78,0x47610001,
0xc78,0x46620001,
0xc78,0x45630001,
0xc78,0x44640001,
0xc78,0x43650001,
0xc78,0x28660001,
0xc78,0x27670001,
0xc78,0x26680001,
0xc78,0x25690001,
0xc78,0x246a0001,
0xc78,0x236b0001,
0xc78,0x226c0001,
0xc78,0x216d0001,
0xc78,0x206e0001,
0xc78,0x0a6f0001,
0xc78,0x08700001,
0xc78,0x06710001,
0xc78,0x05720001,
0xc78,0x04730001,
0xc78,0x03740001,
0xc78,0x02750001,
0xc78,0x01760001,
0xc78,0x00770001,
0xc78,0x00780001,
0xc78,0x00790001,
0xc78,0x007a0001,
0xc78,0x007b0001,
0xc78,0x007c0001,
0xc78,0x007d0001,
0xc78,0x007e0001,
0xc78,0x007f0001,
0xc78,0x2e00001e,
0xc78,0x2e01001e,
0xc78,0x2e02001e,
0xc78,0x2e03001e,
0xc78,0x2e04001e,
0xc78,0x2e05001e,
0xc78,0x3006001e,
0xc78,0x3407001e,
0xc78,0x3908001e,
0xc78,0x3c09001e,
0xc78,0x3f0a001e,
0xc78,0x420b001e,
0xc78,0x440c001e,
0xc78,0x450d001e,
0xc78,0x460e001e,
0xc78,0x460f001e,
0xc78,0x4710001e,
0xc78,0x4811001e,
0xc78,0x4912001e,
0xc78,0x4a13001e,
0xc78,0x4b14001e,
0xc78,0x4b15001e,
0xc78,0x4c16001e,
0xc78,0x4d17001e,
0xc78,0x4e18001e,
0xc78,0x4f19001e,
0xc78,0x4f1a001e,
0xc78,0x501b001e,
0xc78,0x511c001e,
0xc78,0x521d001e,
0xc78,0x521e001e,
0xc78,0x531f001e,
0xc78,0x5320001e,
0xc78,0x5421001e,
0xc78,0x5522001e,
0xc78,0x5523001e,
0xc78,0x5624001e,
0xc78,0x5725001e,
0xc78,0x5726001e,
0xc78,0x5827001e,
0xc78,0x5828001e,
0xc78,0x5929001e,
0xc78,0x592a001e,
0xc78,0x5a2b001e,
0xc78,0x5b2c001e,
0xc78,0x5c2d001e,
0xc78,0x5c2e001e,
0xc78,0x5d2f001e,
0xc78,0x5e30001e,
0xc78,0x5f31001e,
0xc78,0x6032001e,
0xc78,0x6033001e,
0xc78,0x6134001e,
0xc78,0x6235001e,
0xc78,0x6336001e,
0xc78,0x6437001e,
0xc78,0x6438001e,
0xc78,0x6539001e,
0xc78,0x663a001e,
0xc78,0x673b001e,
0xc78,0x673c001e,
0xc78,0x683d001e,
0xc78,0x693e001e,
0xc78,0x6a3f001e,
};
static u32 Rtl8192PciEPHY_REGArray[PHY_REGArrayLength] = {
0x0, };
static u32 Rtl8192PciEPHY_REG_1T2RArray[PHY_REG_1T2RArrayLength] = {
0x800,0x00000000,
0x804,0x00000001,
0x808,0x0000fc00,
0x80c,0x0000001c,
0x810,0x801010aa,
0x814,0x008514d0,
0x818,0x00000040,
0x81c,0x00000000,
0x820,0x00000004,
0x824,0x00690000,
0x828,0x00000004,
0x82c,0x00e90000,
0x830,0x00000004,
0x834,0x00690000,
0x838,0x00000004,
0x83c,0x00e90000,
0x840,0x00000000,
0x844,0x00000000,
0x848,0x00000000,
0x84c,0x00000000,
0x850,0x00000000,
0x854,0x00000000,
0x858,0x65a965a9,
0x85c,0x65a965a9,
0x860,0x001f0010,
0x864,0x007f0010,
0x868,0x001f0010,
0x86c,0x007f0010,
0x870,0x0f100f70,
0x874,0x0f100f70,
0x878,0x00000000,
0x87c,0x00000000,
0x880,0x6870e36c,
0x884,0xe3573600,
0x888,0x4260c340,
0x88c,0x0000ff00,
0x890,0x00000000,
0x894,0xfffffffe,
0x898,0x4c42382f,
0x89c,0x00656056,
0x8b0,0x00000000,
0x8e0,0x00000000,
0x8e4,0x00000000,
0x900,0x00000000,
0x904,0x00000023,
0x908,0x00000000,
0x90c,0x31121311,
0xa00,0x00d0c7d8,
0xa04,0x811f0008,
0xa08,0x80cd8300,
0xa0c,0x2e62740f,
0xa10,0x95009b78,
0xa14,0x11145008,
0xa18,0x00881117,
0xa1c,0x89140fa0,
0xa20,0x1a1b0000,
0xa24,0x090e1317,
0xa28,0x00000204,
0xa2c,0x00000000,
0xc00,0x00000040,
0xc04,0x00005433,
0xc08,0x000000e4,
0xc0c,0x6c6c6c6c,
0xc10,0x08800000,
0xc14,0x40000100,
0xc18,0x08000000,
0xc1c,0x40000100,
0xc20,0x08000000,
0xc24,0x40000100,
0xc28,0x08000000,
0xc2c,0x40000100,
0xc30,0x6de9ac44,
0xc34,0x465c52cd,
0xc38,0x497f5994,
0xc3c,0x0a969764,
0xc40,0x1f7c403f,
0xc44,0x000100b7,
0xc48,0xec020000,
0xc4c,0x00000300,
0xc50,0x69543420,
0xc54,0x433c0094,
0xc58,0x69543420,
0xc5c,0x433c0094,
0xc60,0x69543420,
0xc64,0x433c0094,
0xc68,0x69543420,
0xc6c,0x433c0094,
0xc70,0x2c7f000d,
0xc74,0x0186175b,
0xc78,0x0000001f,
0xc7c,0x00b91612,
0xc80,0x40000100,
0xc84,0x20000000,
0xc88,0x40000100,
0xc8c,0x20200000,
0xc90,0x40000100,
0xc94,0x00000000,
0xc98,0x40000100,
0xc9c,0x00000000,
0xca0,0x00492492,
0xca4,0x00000000,
0xca8,0x00000000,
0xcac,0x00000000,
0xcb0,0x00000000,
0xcb4,0x00000000,
0xcb8,0x00000000,
0xcbc,0x00492492,
0xcc0,0x00000000,
0xcc4,0x00000000,
0xcc8,0x00000000,
0xccc,0x00000000,
0xcd0,0x00000000,
0xcd4,0x00000000,
0xcd8,0x64b22427,
0xcdc,0x00766932,
0xce0,0x00222222,
0xd00,0x00000750,
0xd04,0x00000403,
0xd08,0x0000907f,
0xd0c,0x00000001,
0xd10,0xa0633333,
0xd14,0x33333c63,
0xd18,0x6a8f5b6b,
0xd1c,0x00000000,
0xd20,0x00000000,
0xd24,0x00000000,
0xd28,0x00000000,
0xd2c,0xcc979975,
0xd30,0x00000000,
0xd34,0x00000000,
0xd38,0x00000000,
0xd3c,0x00027293,
0xd40,0x00000000,
0xd44,0x00000000,
0xd48,0x00000000,
0xd4c,0x00000000,
0xd50,0x6437140a,
0xd54,0x024dbd02,
0xd58,0x00000000,
0xd5c,0x04032064,
0xe00,0x161a1a1a,
0xe04,0x12121416,
0xe08,0x00001800,
0xe0c,0x00000000,
0xe10,0x161a1a1a,
0xe14,0x12121416,
0xe18,0x161a1a1a,
0xe1c,0x12121416,
};
static u32 Rtl8192PciERadioA_Array[RadioA_ArrayLength] = {
0x019,0x00000003,
0x000,0x000000bf,
0x001,0x00000ee0,
0x002,0x0000004c,
0x003,0x000007f1,
0x004,0x00000975,
0x005,0x00000c58,
0x006,0x00000ae6,
0x007,0x000000ca,
0x008,0x00000e1c,
0x009,0x000007f0,
0x00a,0x000009d0,
0x00b,0x000001ba,
0x00c,0x00000240,
0x00e,0x00000020,
0x00f,0x00000990,
0x012,0x00000806,
0x014,0x000005ab,
0x015,0x00000f80,
0x016,0x00000020,
0x017,0x00000597,
0x018,0x0000050a,
0x01a,0x00000f80,
0x01b,0x00000f5e,
0x01c,0x00000008,
0x01d,0x00000607,
0x01e,0x000006cc,
0x01f,0x00000000,
0x020,0x000001a5,
0x01f,0x00000001,
0x020,0x00000165,
0x01f,0x00000002,
0x020,0x000000c6,
0x01f,0x00000003,
0x020,0x00000086,
0x01f,0x00000004,
0x020,0x00000046,
0x01f,0x00000005,
0x020,0x000001e6,
0x01f,0x00000006,
0x020,0x000001a6,
0x01f,0x00000007,
0x020,0x00000166,
0x01f,0x00000008,
0x020,0x000000c7,
0x01f,0x00000009,
0x020,0x00000087,
0x01f,0x0000000a,
0x020,0x000000f7,
0x01f,0x0000000b,
0x020,0x000000d7,
0x01f,0x0000000c,
0x020,0x000000b7,
0x01f,0x0000000d,
0x020,0x00000097,
0x01f,0x0000000e,
0x020,0x00000077,
0x01f,0x0000000f,
0x020,0x00000057,
0x01f,0x00000010,
0x020,0x00000037,
0x01f,0x00000011,
0x020,0x000000fb,
0x01f,0x00000012,
0x020,0x000000db,
0x01f,0x00000013,
0x020,0x000000bb,
0x01f,0x00000014,
0x020,0x000000ff,
0x01f,0x00000015,
0x020,0x000000e3,
0x01f,0x00000016,
0x020,0x000000c3,
0x01f,0x00000017,
0x020,0x000000a3,
0x01f,0x00000018,
0x020,0x00000083,
0x01f,0x00000019,
0x020,0x00000063,
0x01f,0x0000001a,
0x020,0x00000043,
0x01f,0x0000001b,
0x020,0x00000023,
0x01f,0x0000001c,
0x020,0x00000003,
0x01f,0x0000001d,
0x020,0x000001e3,
0x01f,0x0000001e,
0x020,0x000001c3,
0x01f,0x0000001f,
0x020,0x000001a3,
0x01f,0x00000020,
0x020,0x00000183,
0x01f,0x00000021,
0x020,0x00000163,
0x01f,0x00000022,
0x020,0x00000143,
0x01f,0x00000023,
0x020,0x00000123,
0x01f,0x00000024,
0x020,0x00000103,
0x023,0x00000203,
0x024,0x00000100,
0x00b,0x000001ba,
0x02c,0x000003d7,
0x02d,0x00000ff0,
0x000,0x00000037,
0x004,0x00000160,
0x007,0x00000080,
0x002,0x0000088d,
0x0fe,0x00000000,
0x0fe,0x00000000,
0x016,0x00000200,
0x016,0x00000380,
0x016,0x00000020,
0x016,0x000001a0,
0x000,0x000000bf,
0x00d,0x0000001f,
0x00d,0x00000c9f,
0x002,0x0000004d,
0x000,0x00000cbf,
0x004,0x00000975,
0x007,0x00000700,
};
static u32 Rtl8192PciERadioB_Array[RadioB_ArrayLength] = {
0x019,0x00000003,
0x000,0x000000bf,
0x001,0x000006e0,
0x002,0x0000004c,
0x003,0x000007f1,
0x004,0x00000975,
0x005,0x00000c58,
0x006,0x00000ae6,
0x007,0x000000ca,
0x008,0x00000e1c,
0x000,0x000000b7,
0x00a,0x00000850,
0x000,0x000000bf,
0x00b,0x000001ba,
0x00c,0x00000240,
0x00e,0x00000020,
0x015,0x00000f80,
0x016,0x00000020,
0x017,0x00000597,
0x018,0x0000050a,
0x01a,0x00000e00,
0x01b,0x00000f5e,
0x01d,0x00000607,
0x01e,0x000006cc,
0x00b,0x000001ba,
0x023,0x00000203,
0x024,0x00000100,
0x000,0x00000037,
0x004,0x00000160,
0x016,0x00000200,
0x016,0x00000380,
0x016,0x00000020,
0x016,0x000001a0,
0x00d,0x00000ccc,
0x000,0x000000bf,
0x002,0x0000004d,
0x000,0x00000cbf,
0x004,0x00000975,
0x007,0x00000700,
};
static u32 Rtl8192PciERadioC_Array[RadioC_ArrayLength] = {
0x0, };
static u32 Rtl8192PciERadioD_Array[RadioD_ArrayLength] = {
0x0, };
#endif
/*************************Define local function prototype**********************/
static u32 phy_FwRFSerialRead(struct net_device* dev,RF90_RADIO_PATH_E eRFPath,u32 Offset);
static void phy_FwRFSerialWrite(struct net_device* dev,RF90_RADIO_PATH_E eRFPath,u32 Offset,u32 Data);
/*************************Define local function prototype**********************/
/******************************************************************************
*function: This function read BB parameters from Header file we gen,
* and do register read/write
* input: u32 dwBitMask //taget bit pos in the addr to be modified
* output: none
* return: u32 return the shift bit bit position of the mask
* ****************************************************************************/
static u32 rtl8192_CalculateBitShift(u32 dwBitMask)
{
u32 i;
for (i=0; i<=31; i++)
{
if (((dwBitMask>>i)&0x1) == 1)
break;
}
return i;
}
/******************************************************************************
*function: This function check different RF type to execute legal judgement. If RF Path is illegal, we will return false.
* input: none
* output: none
* return: 0(illegal, false), 1(legal,true)
* ***************************************************************************/
u8 rtl8192_phy_CheckIsLegalRFPath(struct net_device* dev, u32 eRFPath)
{
u8 ret = 1;
struct r8192_priv *priv = ieee80211_priv(dev);
#ifdef RTL8190P
if(priv->rf_type == RF_2T4R)
{
ret= 1;
}
else if (priv->rf_type == RF_1T2R)
{
if(eRFPath == RF90_PATH_A || eRFPath == RF90_PATH_B)
ret = 0;
else if(eRFPath == RF90_PATH_C || eRFPath == RF90_PATH_D)
ret = 1;
}
#else
#ifdef RTL8192E
if (priv->rf_type == RF_2T4R)
ret = 0;
else if (priv->rf_type == RF_1T2R)
{
if (eRFPath == RF90_PATH_A || eRFPath == RF90_PATH_B)
ret = 1;
else if (eRFPath == RF90_PATH_C || eRFPath == RF90_PATH_D)
ret = 0;
}
#endif
#endif
return ret;
}
/******************************************************************************
*function: This function set specific bits to BB register
* input: net_device dev
* u32 dwRegAddr //target addr to be modified
* u32 dwBitMask //taget bit pos in the addr to be modified
* u32 dwData //value to be write
* output: none
* return: none
* notice:
* ****************************************************************************/
void rtl8192_setBBreg(struct net_device* dev, u32 dwRegAddr, u32 dwBitMask, u32 dwData)
{
u32 OriginalValue, BitShift, NewValue;
if(dwBitMask!= bMaskDWord)
{//if not "double word" write
OriginalValue = read_nic_dword(dev, dwRegAddr);
BitShift = rtl8192_CalculateBitShift(dwBitMask);
NewValue = (((OriginalValue) & (~dwBitMask)) | (dwData << BitShift));
write_nic_dword(dev, dwRegAddr, NewValue);
}else
write_nic_dword(dev, dwRegAddr, dwData);
return;
}
/******************************************************************************
*function: This function reads specific bits from BB register
* input: net_device dev
* u32 dwRegAddr //target addr to be readback
* u32 dwBitMask //taget bit pos in the addr to be readback
* output: none
* return: u32 Data //the readback register value
* notice:
* ****************************************************************************/
u32 rtl8192_QueryBBReg(struct net_device* dev, u32 dwRegAddr, u32 dwBitMask)
{
u32 Ret = 0, OriginalValue, BitShift;
OriginalValue = read_nic_dword(dev, dwRegAddr);
BitShift = rtl8192_CalculateBitShift(dwBitMask);
Ret = (OriginalValue & dwBitMask) >> BitShift;
return (Ret);
}
/******************************************************************************
*function: This function read register from RF chip
* input: net_device dev
* RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 Offset //target address to be read
* output: none
* return: u32 readback value
* notice: There are three types of serial operations:(1) Software serial write.(2)Hardware LSSI-Low Speed Serial Interface.(3)Hardware HSSI-High speed serial write. Driver here need to implement (1) and (2)---need more spec for this information.
* ****************************************************************************/
static u32 rtl8192_phy_RFSerialRead(struct net_device* dev, RF90_RADIO_PATH_E eRFPath, u32 Offset)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 ret = 0;
u32 NewOffset = 0;
BB_REGISTER_DEFINITION_T* pPhyReg = &priv->PHYRegDef[eRFPath];
//rtl8192_setBBreg(dev, pPhyReg->rfLSSIReadBack, bLSSIReadBackData, 0);
//make sure RF register offset is correct
Offset &= 0x3f;
//switch page for 8256 RF IC
if (priv->rf_chip == RF_8256)
{
#ifdef RTL8190P
//analog to digital off, for protection
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0x0);// 0x88c[11:8]
#else
#ifdef RTL8192E
//analog to digital off, for protection
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0x0);// 0x88c[11:8]
#endif
#endif
if (Offset >= 31)
{
priv->RfReg0Value[eRFPath] |= 0x140;
//Switch to Reg_Mode2 for Reg 31-45
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16) );
//modify offset
NewOffset = Offset -30;
}
else if (Offset >= 16)
{
priv->RfReg0Value[eRFPath] |= 0x100;
priv->RfReg0Value[eRFPath] &= (~0x40);
//Switch to Reg_Mode 1 for Reg16-30
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16) );
NewOffset = Offset - 15;
}
else
NewOffset = Offset;
}
else
{
RT_TRACE((COMP_PHY|COMP_ERR), "check RF type here, need to be 8256\n");
NewOffset = Offset;
}
//put desired read addr to LSSI control Register
rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadAddress, NewOffset);
//Issue a posedge trigger
//
rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadEdge, 0x0);
rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadEdge, 0x1);
// TODO: we should not delay such a long time. Ask help from SD3
msleep(1);
ret = rtl8192_QueryBBReg(dev, pPhyReg->rfLSSIReadBack, bLSSIReadBackData);
// Switch back to Reg_Mode0;
if(priv->rf_chip == RF_8256)
{
priv->RfReg0Value[eRFPath] &= 0xebf;
rtl8192_setBBreg(
dev,
pPhyReg->rf3wireOffset,
bMaskDWord,
(priv->RfReg0Value[eRFPath] << 16));
#ifdef RTL8190P
if(priv->rf_type == RF_2T4R)
{
//analog to digital on
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0xf);// 0x88c[11:8]
}
else if(priv->rf_type == RF_1T2R)
{
//analog to digital on
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xc00, 0x3);// 0x88c[11:10]
}
#else
#ifdef RTL8192E
//analog to digital on
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x3);// 0x88c[9:8]
#endif
#endif
}
return ret;
}
/******************************************************************************
*function: This function write data to RF register
* input: net_device dev
* RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 Offset //target address to be written
* u32 Data //The new register data to be written
* output: none
* return: none
* notice: For RF8256 only.
===========================================================
*Reg Mode RegCTL[1] RegCTL[0] Note
* (Reg00[12]) (Reg00[10])
*===========================================================
*Reg_Mode0 0 x Reg 0 ~15(0x0 ~ 0xf)
*------------------------------------------------------------------
*Reg_Mode1 1 0 Reg 16 ~30(0x1 ~ 0xf)
*------------------------------------------------------------------
* Reg_Mode2 1 1 Reg 31 ~ 45(0x1 ~ 0xf)
*------------------------------------------------------------------
* ****************************************************************************/
static void rtl8192_phy_RFSerialWrite(struct net_device* dev, RF90_RADIO_PATH_E eRFPath, u32 Offset, u32 Data)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 DataAndAddr = 0, NewOffset = 0;
BB_REGISTER_DEFINITION_T *pPhyReg = &priv->PHYRegDef[eRFPath];
Offset &= 0x3f;
if (priv->rf_chip == RF_8256)
{
#ifdef RTL8190P
//analog to digital off, for protection
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0x0);// 0x88c[11:8]
#else
#ifdef RTL8192E
//analog to digital off, for protection
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0x0);// 0x88c[11:8]
#endif
#endif
if (Offset >= 31)
{
priv->RfReg0Value[eRFPath] |= 0x140;
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath] << 16));
NewOffset = Offset - 30;
}
else if (Offset >= 16)
{
priv->RfReg0Value[eRFPath] |= 0x100;
priv->RfReg0Value[eRFPath] &= (~0x40);
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16));
NewOffset = Offset - 15;
}
else
NewOffset = Offset;
}
else
{
RT_TRACE((COMP_PHY|COMP_ERR), "check RF type here, need to be 8256\n");
NewOffset = Offset;
}
// Put write addr in [5:0] and write data in [31:16]
DataAndAddr = (Data<<16) | (NewOffset&0x3f);
// Write Operation
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, DataAndAddr);
if(Offset==0x0)
priv->RfReg0Value[eRFPath] = Data;
// Switch back to Reg_Mode0;
if(priv->rf_chip == RF_8256)
{
if(Offset != 0)
{
priv->RfReg0Value[eRFPath] &= 0xebf;
rtl8192_setBBreg(
dev,
pPhyReg->rf3wireOffset,
bMaskDWord,
(priv->RfReg0Value[eRFPath] << 16));
}
#ifdef RTL8190P
if(priv->rf_type == RF_2T4R)
{
//analog to digital on
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0xf);// 0x88c[11:8]
}
else if(priv->rf_type == RF_1T2R)
{
//analog to digital on
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xc00, 0x3);// 0x88c[11:10]
}
#else
#ifdef RTL8192E
//analog to digital on
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x3);// 0x88c[9:8]
#endif
#endif
}
return;
}
/******************************************************************************
*function: This function set specific bits to RF register
* input: net_device dev
* RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 RegAddr //target addr to be modified
* u32 BitMask //taget bit pos in the addr to be modified
* u32 Data //value to be write
* output: none
* return: none
* notice:
* ****************************************************************************/
void rtl8192_phy_SetRFReg(struct net_device* dev, RF90_RADIO_PATH_E eRFPath, u32 RegAddr, u32 BitMask, u32 Data)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 Original_Value, BitShift, New_Value;
// u8 time = 0;
if (!rtl8192_phy_CheckIsLegalRFPath(dev, eRFPath))
return;
#ifdef RTL8192E
if(priv->ieee80211->eRFPowerState != eRfOn && !priv->being_init_adapter)
return;
#endif
//spin_lock_irqsave(&priv->rf_lock, flags);
//down(&priv->rf_sem);
RT_TRACE(COMP_PHY, "FW RF CTRL is not ready now\n");
if (priv->Rf_Mode == RF_OP_By_FW)
{
if (BitMask != bMask12Bits) // RF data is 12 bits only
{
Original_Value = phy_FwRFSerialRead(dev, eRFPath, RegAddr);
BitShift = rtl8192_CalculateBitShift(BitMask);
New_Value = (((Original_Value) & (~BitMask)) | (Data<< BitShift));
phy_FwRFSerialWrite(dev, eRFPath, RegAddr, New_Value);
}else
phy_FwRFSerialWrite(dev, eRFPath, RegAddr, Data);
udelay(200);
}
else
{
if (BitMask != bMask12Bits) // RF data is 12 bits only
{
Original_Value = rtl8192_phy_RFSerialRead(dev, eRFPath, RegAddr);
BitShift = rtl8192_CalculateBitShift(BitMask);
New_Value = (((Original_Value) & (~BitMask)) | (Data<< BitShift));
rtl8192_phy_RFSerialWrite(dev, eRFPath, RegAddr, New_Value);
}else
rtl8192_phy_RFSerialWrite(dev, eRFPath, RegAddr, Data);
}
//spin_unlock_irqrestore(&priv->rf_lock, flags);
//up(&priv->rf_sem);
return;
}
/******************************************************************************
*function: This function reads specific bits from RF register
* input: net_device dev
* u32 RegAddr //target addr to be readback
* u32 BitMask //taget bit pos in the addr to be readback
* output: none
* return: u32 Data //the readback register value
* notice:
* ****************************************************************************/
u32 rtl8192_phy_QueryRFReg(struct net_device* dev, RF90_RADIO_PATH_E eRFPath, u32 RegAddr, u32 BitMask)
{
u32 Original_Value, Readback_Value, BitShift;
struct r8192_priv *priv = ieee80211_priv(dev);
if (!rtl8192_phy_CheckIsLegalRFPath(dev, eRFPath))
return 0;
#ifdef RTL8192E
if(priv->ieee80211->eRFPowerState != eRfOn && !priv->being_init_adapter)
return 0;
#endif
down(&priv->rf_sem);
if (priv->Rf_Mode == RF_OP_By_FW)
{
Original_Value = phy_FwRFSerialRead(dev, eRFPath, RegAddr);
udelay(200);
}
else
{
Original_Value = rtl8192_phy_RFSerialRead(dev, eRFPath, RegAddr);
}
BitShift = rtl8192_CalculateBitShift(BitMask);
Readback_Value = (Original_Value & BitMask) >> BitShift;
up(&priv->rf_sem);
// udelay(200);
return (Readback_Value);
}
/******************************************************************************
*function: We support firmware to execute RF-R/W.
* input: dev
* output: none
* return: none
* notice:
* ***************************************************************************/
static u32 phy_FwRFSerialRead(
struct net_device* dev,
RF90_RADIO_PATH_E eRFPath,
u32 Offset )
{
u32 retValue = 0;
u32 Data = 0;
u8 time = 0;
//DbgPrint("FW RF CTRL\n\r");
/* 2007/11/02 MH Firmware RF Write control. By Francis' suggestion, we can
not execute the scheme in the initial step. Otherwise, RF-R/W will waste
much time. This is only for site survey. */
// 1. Read operation need not insert data. bit 0-11
//Data &= bMask12Bits;
// 2. Write RF register address. Bit 12-19
Data |= ((Offset&0xFF)<<12);
// 3. Write RF path. bit 20-21
Data |= ((eRFPath&0x3)<<20);
// 4. Set RF read indicator. bit 22=0
//Data |= 0x00000;
// 5. Trigger Fw to operate the command. bit 31
Data |= 0x80000000;
// 6. We can not execute read operation if bit 31 is 1.
while (read_nic_dword(dev, QPNR)&0x80000000)
{
// If FW can not finish RF-R/W for more than ?? times. We must reset FW.
if (time++ < 100)
{
//DbgPrint("FW not finish RF-R Time=%d\n\r", time);
udelay(10);
}
else
break;
}
// 7. Execute read operation.
write_nic_dword(dev, QPNR, Data);
// 8. Check if firmawre send back RF content.
while (read_nic_dword(dev, QPNR)&0x80000000)
{
// If FW can not finish RF-R/W for more than ?? times. We must reset FW.
if (time++ < 100)
{
//DbgPrint("FW not finish RF-W Time=%d\n\r", time);
udelay(10);
}
else
return (0);
}
retValue = read_nic_dword(dev, RF_DATA);
return (retValue);
} /* phy_FwRFSerialRead */
/******************************************************************************
*function: We support firmware to execute RF-R/W.
* input: dev
* output: none
* return: none
* notice:
* ***************************************************************************/
static void
phy_FwRFSerialWrite(
struct net_device* dev,
RF90_RADIO_PATH_E eRFPath,
u32 Offset,
u32 Data )
{
u8 time = 0;
//DbgPrint("N FW RF CTRL RF-%d OF%02x DATA=%03x\n\r", eRFPath, Offset, Data);
/* 2007/11/02 MH Firmware RF Write control. By Francis' suggestion, we can
not execute the scheme in the initial step. Otherwise, RF-R/W will waste
much time. This is only for site survey. */
// 1. Set driver write bit and 12 bit data. bit 0-11
//Data &= bMask12Bits; // Done by uper layer.
// 2. Write RF register address. bit 12-19
Data |= ((Offset&0xFF)<<12);
// 3. Write RF path. bit 20-21
Data |= ((eRFPath&0x3)<<20);
// 4. Set RF write indicator. bit 22=1
Data |= 0x400000;
// 5. Trigger Fw to operate the command. bit 31=1
Data |= 0x80000000;
// 6. Write operation. We can not write if bit 31 is 1.
while (read_nic_dword(dev, QPNR)&0x80000000)
{
// If FW can not finish RF-R/W for more than ?? times. We must reset FW.
if (time++ < 100)
{
//DbgPrint("FW not finish RF-W Time=%d\n\r", time);
udelay(10);
}
else
break;
}
// 7. No matter check bit. We always force the write. Because FW will
// not accept the command.
write_nic_dword(dev, QPNR, Data);
/* 2007/11/02 MH Acoording to test, we must delay 20us to wait firmware
to finish RF write operation. */
/* 2008/01/17 MH We support delay in firmware side now. */
//delay_us(20);
} /* phy_FwRFSerialWrite */
/******************************************************************************
*function: This function read BB parameters from Header file we gen,
* and do register read/write
* input: dev
* output: none
* return: none
* notice: BB parameters may change all the time, so please make
* sure it has been synced with the newest.
* ***************************************************************************/
void rtl8192_phy_configmac(struct net_device* dev)
{
u32 dwArrayLen = 0, i = 0;
u32* pdwArray = NULL;
struct r8192_priv *priv = ieee80211_priv(dev);
#ifdef TO_DO_LIST
if(Adapter->bInHctTest)
{
RT_TRACE(COMP_PHY, "Rtl819XMACPHY_ArrayDTM\n");
dwArrayLen = MACPHY_ArrayLengthDTM;
pdwArray = Rtl819XMACPHY_ArrayDTM;
}
else if(priv->bTXPowerDataReadFromEEPORM)
#endif
if(priv->bTXPowerDataReadFromEEPORM)
{
RT_TRACE(COMP_PHY, "Rtl819XMACPHY_Array_PG\n");
dwArrayLen = MACPHY_Array_PGLength;
pdwArray = Rtl819XMACPHY_Array_PG;
}
else
{
RT_TRACE(COMP_PHY,"Read rtl819XMACPHY_Array\n");
dwArrayLen = MACPHY_ArrayLength;
pdwArray = Rtl819XMACPHY_Array;
}
for(i = 0; i<dwArrayLen; i=i+3){
RT_TRACE(COMP_DBG, "The Rtl8190MACPHY_Array[0] is %x Rtl8190MACPHY_Array[1] is %x Rtl8190MACPHY_Array[2] is %x\n",
pdwArray[i], pdwArray[i+1], pdwArray[i+2]);
if(pdwArray[i] == 0x318)
{
pdwArray[i+2] = 0x00000800;
//DbgPrint("ptrArray[i], ptrArray[i+1], ptrArray[i+2] = %x, %x, %x\n",
// ptrArray[i], ptrArray[i+1], ptrArray[i+2]);
}
rtl8192_setBBreg(dev, pdwArray[i], pdwArray[i+1], pdwArray[i+2]);
}
return;
}
/******************************************************************************
*function: This function do dirty work
* input: dev
* output: none
* return: none
* notice: BB parameters may change all the time, so please make
* sure it has been synced with the newest.
* ***************************************************************************/
void rtl8192_phyConfigBB(struct net_device* dev, u8 ConfigType)
{
int i;
//u8 ArrayLength;
u32* Rtl819XPHY_REGArray_Table = NULL;
u32* Rtl819XAGCTAB_Array_Table = NULL;
u16 AGCTAB_ArrayLen, PHY_REGArrayLen = 0;
struct r8192_priv *priv = ieee80211_priv(dev);
#ifdef TO_DO_LIST
u32 *rtl8192PhyRegArrayTable = NULL, *rtl8192AgcTabArrayTable = NULL;
if(Adapter->bInHctTest)
{
AGCTAB_ArrayLen = AGCTAB_ArrayLengthDTM;
Rtl819XAGCTAB_Array_Table = Rtl819XAGCTAB_ArrayDTM;
if(priv->RF_Type == RF_2T4R)
{
PHY_REGArrayLen = PHY_REGArrayLengthDTM;
Rtl819XPHY_REGArray_Table = Rtl819XPHY_REGArrayDTM;
}
else if (priv->RF_Type == RF_1T2R)
{
PHY_REGArrayLen = PHY_REG_1T2RArrayLengthDTM;
Rtl819XPHY_REGArray_Table = Rtl819XPHY_REG_1T2RArrayDTM;
}
}
else
#endif
{
AGCTAB_ArrayLen = AGCTAB_ArrayLength;
Rtl819XAGCTAB_Array_Table = Rtl819XAGCTAB_Array;
if(priv->rf_type == RF_2T4R)
{
PHY_REGArrayLen = PHY_REGArrayLength;
Rtl819XPHY_REGArray_Table = Rtl819XPHY_REGArray;
}
else if (priv->rf_type == RF_1T2R)
{
PHY_REGArrayLen = PHY_REG_1T2RArrayLength;
Rtl819XPHY_REGArray_Table = Rtl819XPHY_REG_1T2RArray;
}
}
if (ConfigType == BaseBand_Config_PHY_REG)
{
for (i=0; i<PHY_REGArrayLen; i+=2)
{
rtl8192_setBBreg(dev, Rtl819XPHY_REGArray_Table[i], bMaskDWord, Rtl819XPHY_REGArray_Table[i+1]);
RT_TRACE(COMP_DBG, "i: %x, The Rtl819xUsbPHY_REGArray[0] is %x Rtl819xUsbPHY_REGArray[1] is %x \n",i, Rtl819XPHY_REGArray_Table[i], Rtl819XPHY_REGArray_Table[i+1]);
}
}
else if (ConfigType == BaseBand_Config_AGC_TAB)
{
for (i=0; i<AGCTAB_ArrayLen; i+=2)
{
rtl8192_setBBreg(dev, Rtl819XAGCTAB_Array_Table[i], bMaskDWord, Rtl819XAGCTAB_Array_Table[i+1]);
RT_TRACE(COMP_DBG, "i:%x, The rtl819XAGCTAB_Array[0] is %x rtl819XAGCTAB_Array[1] is %x \n",i, Rtl819XAGCTAB_Array_Table[i], Rtl819XAGCTAB_Array_Table[i+1]);
}
}
return;
}
/******************************************************************************
*function: This function initialize Register definition offset for Radio Path
* A/B/C/D
* input: net_device dev
* output: none
* return: none
* notice: Initialization value here is constant and it should never be changed
* ***************************************************************************/
static void rtl8192_InitBBRFRegDef(struct net_device* dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
// RF Interface Sowrtware Control
priv->PHYRegDef[RF90_PATH_A].rfintfs = rFPGA0_XAB_RFInterfaceSW; // 16 LSBs if read 32-bit from 0x870
priv->PHYRegDef[RF90_PATH_B].rfintfs = rFPGA0_XAB_RFInterfaceSW; // 16 MSBs if read 32-bit from 0x870 (16-bit for 0x872)
priv->PHYRegDef[RF90_PATH_C].rfintfs = rFPGA0_XCD_RFInterfaceSW;// 16 LSBs if read 32-bit from 0x874
priv->PHYRegDef[RF90_PATH_D].rfintfs = rFPGA0_XCD_RFInterfaceSW;// 16 MSBs if read 32-bit from 0x874 (16-bit for 0x876)
// RF Interface Readback Value
priv->PHYRegDef[RF90_PATH_A].rfintfi = rFPGA0_XAB_RFInterfaceRB; // 16 LSBs if read 32-bit from 0x8E0
priv->PHYRegDef[RF90_PATH_B].rfintfi = rFPGA0_XAB_RFInterfaceRB;// 16 MSBs if read 32-bit from 0x8E0 (16-bit for 0x8E2)
priv->PHYRegDef[RF90_PATH_C].rfintfi = rFPGA0_XCD_RFInterfaceRB;// 16 LSBs if read 32-bit from 0x8E4
priv->PHYRegDef[RF90_PATH_D].rfintfi = rFPGA0_XCD_RFInterfaceRB;// 16 MSBs if read 32-bit from 0x8E4 (16-bit for 0x8E6)
// RF Interface Output (and Enable)
priv->PHYRegDef[RF90_PATH_A].rfintfo = rFPGA0_XA_RFInterfaceOE; // 16 LSBs if read 32-bit from 0x860
priv->PHYRegDef[RF90_PATH_B].rfintfo = rFPGA0_XB_RFInterfaceOE; // 16 LSBs if read 32-bit from 0x864
priv->PHYRegDef[RF90_PATH_C].rfintfo = rFPGA0_XC_RFInterfaceOE;// 16 LSBs if read 32-bit from 0x868
priv->PHYRegDef[RF90_PATH_D].rfintfo = rFPGA0_XD_RFInterfaceOE;// 16 LSBs if read 32-bit from 0x86C
// RF Interface (Output and) Enable
priv->PHYRegDef[RF90_PATH_A].rfintfe = rFPGA0_XA_RFInterfaceOE; // 16 MSBs if read 32-bit from 0x860 (16-bit for 0x862)
priv->PHYRegDef[RF90_PATH_B].rfintfe = rFPGA0_XB_RFInterfaceOE; // 16 MSBs if read 32-bit from 0x864 (16-bit for 0x866)
priv->PHYRegDef[RF90_PATH_C].rfintfe = rFPGA0_XC_RFInterfaceOE;// 16 MSBs if read 32-bit from 0x86A (16-bit for 0x86A)
priv->PHYRegDef[RF90_PATH_D].rfintfe = rFPGA0_XD_RFInterfaceOE;// 16 MSBs if read 32-bit from 0x86C (16-bit for 0x86E)
//Addr of LSSI. Wirte RF register by driver
priv->PHYRegDef[RF90_PATH_A].rf3wireOffset = rFPGA0_XA_LSSIParameter; //LSSI Parameter
priv->PHYRegDef[RF90_PATH_B].rf3wireOffset = rFPGA0_XB_LSSIParameter;
priv->PHYRegDef[RF90_PATH_C].rf3wireOffset = rFPGA0_XC_LSSIParameter;
priv->PHYRegDef[RF90_PATH_D].rf3wireOffset = rFPGA0_XD_LSSIParameter;
// RF parameter
priv->PHYRegDef[RF90_PATH_A].rfLSSI_Select = rFPGA0_XAB_RFParameter; //BB Band Select
priv->PHYRegDef[RF90_PATH_B].rfLSSI_Select = rFPGA0_XAB_RFParameter;
priv->PHYRegDef[RF90_PATH_C].rfLSSI_Select = rFPGA0_XCD_RFParameter;
priv->PHYRegDef[RF90_PATH_D].rfLSSI_Select = rFPGA0_XCD_RFParameter;
// Tx AGC Gain Stage (same for all path. Should we remove this?)
priv->PHYRegDef[RF90_PATH_A].rfTxGainStage = rFPGA0_TxGainStage; //Tx gain stage
priv->PHYRegDef[RF90_PATH_B].rfTxGainStage = rFPGA0_TxGainStage; //Tx gain stage
priv->PHYRegDef[RF90_PATH_C].rfTxGainStage = rFPGA0_TxGainStage; //Tx gain stage
priv->PHYRegDef[RF90_PATH_D].rfTxGainStage = rFPGA0_TxGainStage; //Tx gain stage
// Tranceiver A~D HSSI Parameter-1
priv->PHYRegDef[RF90_PATH_A].rfHSSIPara1 = rFPGA0_XA_HSSIParameter1; //wire control parameter1
priv->PHYRegDef[RF90_PATH_B].rfHSSIPara1 = rFPGA0_XB_HSSIParameter1; //wire control parameter1
priv->PHYRegDef[RF90_PATH_C].rfHSSIPara1 = rFPGA0_XC_HSSIParameter1; //wire control parameter1
priv->PHYRegDef[RF90_PATH_D].rfHSSIPara1 = rFPGA0_XD_HSSIParameter1; //wire control parameter1
// Tranceiver A~D HSSI Parameter-2
priv->PHYRegDef[RF90_PATH_A].rfHSSIPara2 = rFPGA0_XA_HSSIParameter2; //wire control parameter2
priv->PHYRegDef[RF90_PATH_B].rfHSSIPara2 = rFPGA0_XB_HSSIParameter2; //wire control parameter2
priv->PHYRegDef[RF90_PATH_C].rfHSSIPara2 = rFPGA0_XC_HSSIParameter2; //wire control parameter2
priv->PHYRegDef[RF90_PATH_D].rfHSSIPara2 = rFPGA0_XD_HSSIParameter2; //wire control parameter1
// RF switch Control
priv->PHYRegDef[RF90_PATH_A].rfSwitchControl = rFPGA0_XAB_SwitchControl; //TR/Ant switch control
priv->PHYRegDef[RF90_PATH_B].rfSwitchControl = rFPGA0_XAB_SwitchControl;
priv->PHYRegDef[RF90_PATH_C].rfSwitchControl = rFPGA0_XCD_SwitchControl;
priv->PHYRegDef[RF90_PATH_D].rfSwitchControl = rFPGA0_XCD_SwitchControl;
// AGC control 1
priv->PHYRegDef[RF90_PATH_A].rfAGCControl1 = rOFDM0_XAAGCCore1;
priv->PHYRegDef[RF90_PATH_B].rfAGCControl1 = rOFDM0_XBAGCCore1;
priv->PHYRegDef[RF90_PATH_C].rfAGCControl1 = rOFDM0_XCAGCCore1;
priv->PHYRegDef[RF90_PATH_D].rfAGCControl1 = rOFDM0_XDAGCCore1;
// AGC control 2
priv->PHYRegDef[RF90_PATH_A].rfAGCControl2 = rOFDM0_XAAGCCore2;
priv->PHYRegDef[RF90_PATH_B].rfAGCControl2 = rOFDM0_XBAGCCore2;
priv->PHYRegDef[RF90_PATH_C].rfAGCControl2 = rOFDM0_XCAGCCore2;
priv->PHYRegDef[RF90_PATH_D].rfAGCControl2 = rOFDM0_XDAGCCore2;
// RX AFE control 1
priv->PHYRegDef[RF90_PATH_A].rfRxIQImbalance = rOFDM0_XARxIQImbalance;
priv->PHYRegDef[RF90_PATH_B].rfRxIQImbalance = rOFDM0_XBRxIQImbalance;
priv->PHYRegDef[RF90_PATH_C].rfRxIQImbalance = rOFDM0_XCRxIQImbalance;
priv->PHYRegDef[RF90_PATH_D].rfRxIQImbalance = rOFDM0_XDRxIQImbalance;
// RX AFE control 1
priv->PHYRegDef[RF90_PATH_A].rfRxAFE = rOFDM0_XARxAFE;
priv->PHYRegDef[RF90_PATH_B].rfRxAFE = rOFDM0_XBRxAFE;
priv->PHYRegDef[RF90_PATH_C].rfRxAFE = rOFDM0_XCRxAFE;
priv->PHYRegDef[RF90_PATH_D].rfRxAFE = rOFDM0_XDRxAFE;
// Tx AFE control 1
priv->PHYRegDef[RF90_PATH_A].rfTxIQImbalance = rOFDM0_XATxIQImbalance;
priv->PHYRegDef[RF90_PATH_B].rfTxIQImbalance = rOFDM0_XBTxIQImbalance;
priv->PHYRegDef[RF90_PATH_C].rfTxIQImbalance = rOFDM0_XCTxIQImbalance;
priv->PHYRegDef[RF90_PATH_D].rfTxIQImbalance = rOFDM0_XDTxIQImbalance;
// Tx AFE control 2
priv->PHYRegDef[RF90_PATH_A].rfTxAFE = rOFDM0_XATxAFE;
priv->PHYRegDef[RF90_PATH_B].rfTxAFE = rOFDM0_XBTxAFE;
priv->PHYRegDef[RF90_PATH_C].rfTxAFE = rOFDM0_XCTxAFE;
priv->PHYRegDef[RF90_PATH_D].rfTxAFE = rOFDM0_XDTxAFE;
// Tranceiver LSSI Readback
priv->PHYRegDef[RF90_PATH_A].rfLSSIReadBack = rFPGA0_XA_LSSIReadBack;
priv->PHYRegDef[RF90_PATH_B].rfLSSIReadBack = rFPGA0_XB_LSSIReadBack;
priv->PHYRegDef[RF90_PATH_C].rfLSSIReadBack = rFPGA0_XC_LSSIReadBack;
priv->PHYRegDef[RF90_PATH_D].rfLSSIReadBack = rFPGA0_XD_LSSIReadBack;
}
/******************************************************************************
*function: This function is to write register and then readback to make sure whether BB and RF is OK
* input: net_device dev
* HW90_BLOCK_E CheckBlock
* RF90_RADIO_PATH_E eRFPath //only used when checkblock is HW90_BLOCK_RF
* output: none
* return: return whether BB and RF is ok(0:OK; 1:Fail)
* notice: This function may be removed in the ASIC
* ***************************************************************************/
RT_STATUS rtl8192_phy_checkBBAndRF(struct net_device* dev, HW90_BLOCK_E CheckBlock, RF90_RADIO_PATH_E eRFPath)
{
//struct r8192_priv *priv = ieee80211_priv(dev);
// BB_REGISTER_DEFINITION_T *pPhyReg = &priv->PHYRegDef[eRFPath];
RT_STATUS ret = RT_STATUS_SUCCESS;
u32 i, CheckTimes = 4, dwRegRead = 0;
u32 WriteAddr[4];
u32 WriteData[] = {0xfffff027, 0xaa55a02f, 0x00000027, 0x55aa502f};
// Initialize register address offset to be checked
WriteAddr[HW90_BLOCK_MAC] = 0x100;
WriteAddr[HW90_BLOCK_PHY0] = 0x900;
WriteAddr[HW90_BLOCK_PHY1] = 0x800;
WriteAddr[HW90_BLOCK_RF] = 0x3;
RT_TRACE(COMP_PHY, "=======>%s(), CheckBlock:%d\n", __FUNCTION__, CheckBlock);
for(i=0 ; i < CheckTimes ; i++)
{
//
// Write Data to register and readback
//
switch(CheckBlock)
{
case HW90_BLOCK_MAC:
RT_TRACE(COMP_ERR, "PHY_CheckBBRFOK(): Never Write 0x100 here!");
break;
case HW90_BLOCK_PHY0:
case HW90_BLOCK_PHY1:
write_nic_dword(dev, WriteAddr[CheckBlock], WriteData[i]);
dwRegRead = read_nic_dword(dev, WriteAddr[CheckBlock]);
break;
case HW90_BLOCK_RF:
WriteData[i] &= 0xfff;
rtl8192_phy_SetRFReg(dev, eRFPath, WriteAddr[HW90_BLOCK_RF], bMask12Bits, WriteData[i]);
// TODO: we should not delay for such a long time. Ask SD3
mdelay(10);
dwRegRead = rtl8192_phy_QueryRFReg(dev, eRFPath, WriteAddr[HW90_BLOCK_RF], bMaskDWord);
mdelay(10);
break;
default:
ret = RT_STATUS_FAILURE;
break;
}
//
// Check whether readback data is correct
//
if(dwRegRead != WriteData[i])
{
RT_TRACE(COMP_ERR, "====>error=====dwRegRead: %x, WriteData: %x \n", dwRegRead, WriteData[i]);
ret = RT_STATUS_FAILURE;
break;
}
}
return ret;
}
/******************************************************************************
*function: This function initialize BB&RF
* input: net_device dev
* output: none
* return: none
* notice: Initialization value may change all the time, so please make
* sure it has been synced with the newest.
* ***************************************************************************/
static RT_STATUS rtl8192_BB_Config_ParaFile(struct net_device* dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
RT_STATUS rtStatus = RT_STATUS_SUCCESS;
u8 bRegValue = 0, eCheckItem = 0;
u32 dwRegValue = 0;
/**************************************
//<1>Initialize BaseBand
**************************************/
/*--set BB Global Reset--*/
bRegValue = read_nic_byte(dev, BB_GLOBAL_RESET);
write_nic_byte(dev, BB_GLOBAL_RESET,(bRegValue|BB_GLOBAL_RESET_BIT));
/*---set BB reset Active---*/
dwRegValue = read_nic_dword(dev, CPU_GEN);
write_nic_dword(dev, CPU_GEN, (dwRegValue&(~CPU_GEN_BB_RST)));
/*----Ckeck FPGAPHY0 and PHY1 board is OK----*/
// TODO: this function should be removed on ASIC , Emily 2007.2.2
for(eCheckItem=(HW90_BLOCK_E)HW90_BLOCK_PHY0; eCheckItem<=HW90_BLOCK_PHY1; eCheckItem++)
{
rtStatus = rtl8192_phy_checkBBAndRF(dev, (HW90_BLOCK_E)eCheckItem, (RF90_RADIO_PATH_E)0); //don't care RF path
if(rtStatus != RT_STATUS_SUCCESS)
{
RT_TRACE((COMP_ERR | COMP_PHY), "PHY_RF8256_Config():Check PHY%d Fail!!\n", eCheckItem-1);
return rtStatus;
}
}
/*---- Set CCK and OFDM Block "OFF"----*/
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bCCKEn|bOFDMEn, 0x0);
/*----BB Register Initilazation----*/
//==m==>Set PHY REG From Header<==m==
rtl8192_phyConfigBB(dev, BaseBand_Config_PHY_REG);
/*----Set BB reset de-Active----*/
dwRegValue = read_nic_dword(dev, CPU_GEN);
write_nic_dword(dev, CPU_GEN, (dwRegValue|CPU_GEN_BB_RST));
/*----BB AGC table Initialization----*/
//==m==>Set PHY REG From Header<==m==
rtl8192_phyConfigBB(dev, BaseBand_Config_AGC_TAB);
if (priv->card_8192_version > VERSION_8190_BD)
{
if(priv->rf_type == RF_2T4R)
{
// Antenna gain offset from B/C/D to A
dwRegValue = ( priv->AntennaTxPwDiff[2]<<8 |
priv->AntennaTxPwDiff[1]<<4 |
priv->AntennaTxPwDiff[0]);
}
else
dwRegValue = 0x0; //Antenna gain offset doesn't make sense in RF 1T2R.
rtl8192_setBBreg(dev, rFPGA0_TxGainStage,
(bXBTxAGC|bXCTxAGC|bXDTxAGC), dwRegValue);
//XSTALLCap
#ifdef RTL8190P
dwRegValue = priv->CrystalCap & 0x3; // bit0~1 of crystal cap
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, bXtalCap01, dwRegValue);
dwRegValue = ((priv->CrystalCap & 0xc)>>2); // bit2~3 of crystal cap
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter2, bXtalCap23, dwRegValue);
#else
#ifdef RTL8192E
dwRegValue = priv->CrystalCap;
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, bXtalCap92x, dwRegValue);
#endif
#endif
}
// Check if the CCK HighPower is turned ON.
// This is used to calculate PWDB.
// priv->bCckHighPower = (u8)(rtl8192_QueryBBReg(dev, rFPGA0_XA_HSSIParameter2, 0x200));
return rtStatus;
}
/******************************************************************************
*function: This function initialize BB&RF
* input: net_device dev
* output: none
* return: none
* notice: Initialization value may change all the time, so please make
* sure it has been synced with the newest.
* ***************************************************************************/
RT_STATUS rtl8192_BBConfig(struct net_device* dev)
{
RT_STATUS rtStatus = RT_STATUS_SUCCESS;
rtl8192_InitBBRFRegDef(dev);
//config BB&RF. As hardCode based initialization has not been well
//implemented, so use file first.FIXME:should implement it for hardcode?
rtStatus = rtl8192_BB_Config_ParaFile(dev);
return rtStatus;
}
/******************************************************************************
*function: This function obtains the initialization value of Tx power Level offset
* input: net_device dev
* output: none
* return: none
* ***************************************************************************/
void rtl8192_phy_getTxPower(struct net_device* dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
#ifdef RTL8190P
priv->MCSTxPowerLevelOriginalOffset[0] =
read_nic_dword(dev, MCS_TXAGC);
priv->MCSTxPowerLevelOriginalOffset[1] =
read_nic_dword(dev, (MCS_TXAGC+4));
priv->CCKTxPowerLevelOriginalOffset =
read_nic_dword(dev, CCK_TXAGC);
#else
#ifdef RTL8192E
priv->MCSTxPowerLevelOriginalOffset[0] =
read_nic_dword(dev, rTxAGC_Rate18_06);
priv->MCSTxPowerLevelOriginalOffset[1] =
read_nic_dword(dev, rTxAGC_Rate54_24);
priv->MCSTxPowerLevelOriginalOffset[2] =
read_nic_dword(dev, rTxAGC_Mcs03_Mcs00);
priv->MCSTxPowerLevelOriginalOffset[3] =
read_nic_dword(dev, rTxAGC_Mcs07_Mcs04);
priv->MCSTxPowerLevelOriginalOffset[4] =
read_nic_dword(dev, rTxAGC_Mcs11_Mcs08);
priv->MCSTxPowerLevelOriginalOffset[5] =
read_nic_dword(dev, rTxAGC_Mcs15_Mcs12);
#endif
#endif
// read rx initial gain
priv->DefaultInitialGain[0] = read_nic_byte(dev, rOFDM0_XAAGCCore1);
priv->DefaultInitialGain[1] = read_nic_byte(dev, rOFDM0_XBAGCCore1);
priv->DefaultInitialGain[2] = read_nic_byte(dev, rOFDM0_XCAGCCore1);
priv->DefaultInitialGain[3] = read_nic_byte(dev, rOFDM0_XDAGCCore1);
RT_TRACE(COMP_INIT, "Default initial gain (c50=0x%x, c58=0x%x, c60=0x%x, c68=0x%x) \n",
priv->DefaultInitialGain[0], priv->DefaultInitialGain[1],
priv->DefaultInitialGain[2], priv->DefaultInitialGain[3]);
// read framesync
priv->framesync = read_nic_byte(dev, rOFDM0_RxDetector3);
priv->framesyncC34 = read_nic_dword(dev, rOFDM0_RxDetector2);
RT_TRACE(COMP_INIT, "Default framesync (0x%x) = 0x%x \n",
rOFDM0_RxDetector3, priv->framesync);
// read SIFS (save the value read fome MACPHY_REG.txt)
priv->SifsTime = read_nic_word(dev, SIFS);
return;
}
/******************************************************************************
*function: This function obtains the initialization value of Tx power Level offset
* input: net_device dev
* output: none
* return: none
* ***************************************************************************/
void rtl8192_phy_setTxPower(struct net_device* dev, u8 channel)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 powerlevel = 0,powerlevelOFDM24G = 0;
char ant_pwr_diff;
u32 u4RegValue;
if(priv->epromtype == EPROM_93c46)
{
powerlevel = priv->TxPowerLevelCCK[channel-1];
powerlevelOFDM24G = priv->TxPowerLevelOFDM24G[channel-1];
}
else if(priv->epromtype == EPROM_93c56)
{
if(priv->rf_type == RF_1T2R)
{
powerlevel = priv->TxPowerLevelCCK_C[channel-1];
powerlevelOFDM24G = priv->TxPowerLevelOFDM24G_C[channel-1];
}
else if(priv->rf_type == RF_2T4R)
{
// Mainly we use RF-A Tx Power to write the Tx Power registers, but the RF-C Tx
// Power must be calculated by the antenna diff.
// So we have to rewrite Antenna gain offset register here.
powerlevel = priv->TxPowerLevelCCK_A[channel-1];
powerlevelOFDM24G = priv->TxPowerLevelOFDM24G_A[channel-1];
ant_pwr_diff = priv->TxPowerLevelOFDM24G_C[channel-1]
-priv->TxPowerLevelOFDM24G_A[channel-1];
ant_pwr_diff &= 0xf;
//DbgPrint(" ant_pwr_diff = 0x%x", (u8)(ant_pwr_diff));
priv->RF_C_TxPwDiff = ant_pwr_diff;
priv->AntennaTxPwDiff[2] = 0;// RF-D, don't care
priv->AntennaTxPwDiff[1] = (u8)(ant_pwr_diff);// RF-C
priv->AntennaTxPwDiff[0] = 0;// RF-B, don't care
// Antenna gain offset from B/C/D to A
u4RegValue = ( priv->AntennaTxPwDiff[2]<<8 |
priv->AntennaTxPwDiff[1]<<4 |
priv->AntennaTxPwDiff[0]);
rtl8192_setBBreg(dev, rFPGA0_TxGainStage,
(bXBTxAGC|bXCTxAGC|bXDTxAGC), u4RegValue);
}
}
#ifdef TODO
//
// CCX 2 S31, AP control of client transmit power:
// 1. We shall not exceed Cell Power Limit as possible as we can.
// 2. Tolerance is +/- 5dB.
// 3. 802.11h Power Contraint takes higher precedence over CCX Cell Power Limit.
//
// TODO:
// 1. 802.11h power contraint
//
// 071011, by rcnjko.
//
if( pMgntInfo->OpMode == RT_OP_MODE_INFRASTRUCTURE &&
pMgntInfo->bWithCcxCellPwr &&
channel == pMgntInfo->dot11CurrentChannelNumber)
{
u8 CckCellPwrIdx = DbmToTxPwrIdx(Adapter, WIRELESS_MODE_B, pMgntInfo->CcxCellPwr);
u8 LegacyOfdmCellPwrIdx = DbmToTxPwrIdx(Adapter, WIRELESS_MODE_G, pMgntInfo->CcxCellPwr);
u8 OfdmCellPwrIdx = DbmToTxPwrIdx(Adapter, WIRELESS_MODE_N_24G, pMgntInfo->CcxCellPwr);
RT_TRACE(COMP_TXAGC, DBG_LOUD,
("CCX Cell Limit: %d dbm => CCK Tx power index : %d, Legacy OFDM Tx power index : %d, OFDM Tx power index: %d\n",
pMgntInfo->CcxCellPwr, CckCellPwrIdx, LegacyOfdmCellPwrIdx, OfdmCellPwrIdx));
RT_TRACE(COMP_TXAGC, DBG_LOUD,
("EEPROM channel(%d) => CCK Tx power index: %d, Legacy OFDM Tx power index : %d, OFDM Tx power index: %d\n",
channel, powerlevel, powerlevelOFDM24G + pHalData->LegacyHTTxPowerDiff, powerlevelOFDM24G));
// CCK
if(powerlevel > CckCellPwrIdx)
powerlevel = CckCellPwrIdx;
// Legacy OFDM, HT OFDM
if(powerlevelOFDM24G + pHalData->LegacyHTTxPowerDiff > OfdmCellPwrIdx)
{
if((OfdmCellPwrIdx - pHalData->LegacyHTTxPowerDiff) > 0)
{
powerlevelOFDM24G = OfdmCellPwrIdx - pHalData->LegacyHTTxPowerDiff;
}
else
{
LegacyOfdmCellPwrIdx = 0;
}
}
RT_TRACE(COMP_TXAGC, DBG_LOUD,
("Altered CCK Tx power index : %d, Legacy OFDM Tx power index: %d, OFDM Tx power index: %d\n",
powerlevel, powerlevelOFDM24G + pHalData->LegacyHTTxPowerDiff, powerlevelOFDM24G));
}
pHalData->CurrentCckTxPwrIdx = powerlevel;
pHalData->CurrentOfdm24GTxPwrIdx = powerlevelOFDM24G;
#endif
switch(priv->rf_chip)
{
case RF_8225:
// PHY_SetRF8225CckTxPower(Adapter, powerlevel);
// PHY_SetRF8225OfdmTxPower(Adapter, powerlevelOFDM24G);
break;
case RF_8256:
PHY_SetRF8256CCKTxPower(dev, powerlevel); //need further implement
PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G);
break;
case RF_8258:
break;
default:
RT_TRACE(COMP_ERR, "unknown rf chip in funtion %s()\n", __FUNCTION__);
break;
}
return;
}
/******************************************************************************
*function: This function check Rf chip to do RF config
* input: net_device dev
* output: none
* return: only 8256 is supported
* ***************************************************************************/
RT_STATUS rtl8192_phy_RFConfig(struct net_device* dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
RT_STATUS rtStatus = RT_STATUS_SUCCESS;
switch(priv->rf_chip)
{
case RF_8225:
// rtStatus = PHY_RF8225_Config(Adapter);
break;
case RF_8256:
rtStatus = PHY_RF8256_Config(dev);
break;
case RF_8258:
break;
case RF_PSEUDO_11N:
//rtStatus = PHY_RF8225_Config(Adapter);
break;
default:
RT_TRACE(COMP_ERR, "error chip id\n");
break;
}
return rtStatus;
}
/******************************************************************************
*function: This function update Initial gain
* input: net_device dev
* output: none
* return: As Windows has not implemented this, wait for complement
* ***************************************************************************/
void rtl8192_phy_updateInitGain(struct net_device* dev)
{
return;
}
/******************************************************************************
*function: This function read RF parameters from general head file, and do RF 3-wire
* input: net_device dev
* output: none
* return: return code show if RF configuration is successful(0:pass, 1:fail)
* Note: Delay may be required for RF configuration
* ***************************************************************************/
u8 rtl8192_phy_ConfigRFWithHeaderFile(struct net_device* dev, RF90_RADIO_PATH_E eRFPath)
{
int i;
//u32* pRFArray;
u8 ret = 0;
switch(eRFPath){
case RF90_PATH_A:
for(i = 0;i<RadioA_ArrayLength; i=i+2){
if(Rtl819XRadioA_Array[i] == 0xfe){
msleep(100);
continue;
}
rtl8192_phy_SetRFReg(dev, eRFPath, Rtl819XRadioA_Array[i], bMask12Bits, Rtl819XRadioA_Array[i+1]);
//msleep(1);
}
break;
case RF90_PATH_B:
for(i = 0;i<RadioB_ArrayLength; i=i+2){
if(Rtl819XRadioB_Array[i] == 0xfe){
msleep(100);
continue;
}
rtl8192_phy_SetRFReg(dev, eRFPath, Rtl819XRadioB_Array[i], bMask12Bits, Rtl819XRadioB_Array[i+1]);
//msleep(1);
}
break;
case RF90_PATH_C:
for(i = 0;i<RadioC_ArrayLength; i=i+2){
if(Rtl819XRadioC_Array[i] == 0xfe){
msleep(100);
continue;
}
rtl8192_phy_SetRFReg(dev, eRFPath, Rtl819XRadioC_Array[i], bMask12Bits, Rtl819XRadioC_Array[i+1]);
//msleep(1);
}
break;
case RF90_PATH_D:
for(i = 0;i<RadioD_ArrayLength; i=i+2){
if(Rtl819XRadioD_Array[i] == 0xfe){
msleep(100);
continue;
}
rtl8192_phy_SetRFReg(dev, eRFPath, Rtl819XRadioD_Array[i], bMask12Bits, Rtl819XRadioD_Array[i+1]);
//msleep(1);
}
break;
default:
break;
}
return ret;;
}
/******************************************************************************
*function: This function set Tx Power of the channel
* input: struct net_device *dev
* u8 channel
* output: none
* return: none
* Note:
* ***************************************************************************/
static void rtl8192_SetTxPowerLevel(struct net_device *dev, u8 channel)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 powerlevel = priv->TxPowerLevelCCK[channel-1];
u8 powerlevelOFDM24G = priv->TxPowerLevelOFDM24G[channel-1];
switch(priv->rf_chip)
{
case RF_8225:
#ifdef TO_DO_LIST
PHY_SetRF8225CckTxPower(Adapter, powerlevel);
PHY_SetRF8225OfdmTxPower(Adapter, powerlevelOFDM24G);
#endif
break;
case RF_8256:
PHY_SetRF8256CCKTxPower(dev, powerlevel);
PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G);
break;
case RF_8258:
break;
default:
RT_TRACE(COMP_ERR, "unknown rf chip ID in rtl8192_SetTxPowerLevel()\n");
break;
}
return;
}
/****************************************************************************************
*function: This function set command table variable(struct SwChnlCmd).
* input: SwChnlCmd* CmdTable //table to be set.
* u32 CmdTableIdx //variable index in table to be set
* u32 CmdTableSz //table size.
* SwChnlCmdID CmdID //command ID to set.
* u32 Para1
* u32 Para2
* u32 msDelay
* output:
* return: true if finished, false otherwise
* Note:
* ************************************************************************************/
static u8 rtl8192_phy_SetSwChnlCmdArray(
SwChnlCmd* CmdTable,
u32 CmdTableIdx,
u32 CmdTableSz,
SwChnlCmdID CmdID,
u32 Para1,
u32 Para2,
u32 msDelay
)
{
SwChnlCmd* pCmd;
if(CmdTable == NULL)
{
RT_TRACE(COMP_ERR, "phy_SetSwChnlCmdArray(): CmdTable cannot be NULL.\n");
return false;
}
if(CmdTableIdx >= CmdTableSz)
{
RT_TRACE(COMP_ERR, "phy_SetSwChnlCmdArray(): Access invalid index, please check size of the table, CmdTableIdx:%d, CmdTableSz:%d\n",
CmdTableIdx, CmdTableSz);
return false;
}
pCmd = CmdTable + CmdTableIdx;
pCmd->CmdID = CmdID;
pCmd->Para1 = Para1;
pCmd->Para2 = Para2;
pCmd->msDelay = msDelay;
return true;
}
/******************************************************************************
*function: This function set channel step by step
* input: struct net_device *dev
* u8 channel
* u8* stage //3 stages
* u8* step //
* u32* delay //whether need to delay
* output: store new stage, step and delay for next step(combine with function above)
* return: true if finished, false otherwise
* Note: Wait for simpler function to replace it //wb
* ***************************************************************************/
static u8 rtl8192_phy_SwChnlStepByStep(struct net_device *dev, u8 channel, u8* stage, u8* step, u32* delay)
{
struct r8192_priv *priv = ieee80211_priv(dev);
// PCHANNEL_ACCESS_SETTING pChnlAccessSetting;
SwChnlCmd PreCommonCmd[MAX_PRECMD_CNT];
u32 PreCommonCmdCnt;
SwChnlCmd PostCommonCmd[MAX_POSTCMD_CNT];
u32 PostCommonCmdCnt;
SwChnlCmd RfDependCmd[MAX_RFDEPENDCMD_CNT];
u32 RfDependCmdCnt;
SwChnlCmd *CurrentCmd = NULL;
//RF90_RADIO_PATH_E eRFPath;
u8 eRFPath;
// u32 RfRetVal;
// u8 RetryCnt;
RT_TRACE(COMP_TRACE, "====>%s()====stage:%d, step:%d, channel:%d\n", __FUNCTION__, *stage, *step, channel);
// RT_ASSERT(IsLegalChannel(Adapter, channel), ("illegal channel: %d\n", channel));
#ifdef ENABLE_DOT11D
if (!IsLegalChannel(priv->ieee80211, channel))
{
RT_TRACE(COMP_ERR, "=============>set to illegal channel:%d\n", channel);
return true; //return true to tell upper caller function this channel setting is finished! Or it will in while loop.
}
#endif
//for(eRFPath = RF90_PATH_A; eRFPath <pHalData->NumTotalRFPath; eRFPath++)
//for(eRFPath = 0; eRFPath <RF90_PATH_MAX; eRFPath++)
{
//if (!rtl8192_phy_CheckIsLegalRFPath(dev, eRFPath))
// return false;
// <1> Fill up pre common command.
PreCommonCmdCnt = 0;
rtl8192_phy_SetSwChnlCmdArray(PreCommonCmd, PreCommonCmdCnt++, MAX_PRECMD_CNT,
CmdID_SetTxPowerLevel, 0, 0, 0);
rtl8192_phy_SetSwChnlCmdArray(PreCommonCmd, PreCommonCmdCnt++, MAX_PRECMD_CNT,
CmdID_End, 0, 0, 0);
// <2> Fill up post common command.
PostCommonCmdCnt = 0;
rtl8192_phy_SetSwChnlCmdArray(PostCommonCmd, PostCommonCmdCnt++, MAX_POSTCMD_CNT,
CmdID_End, 0, 0, 0);
// <3> Fill up RF dependent command.
RfDependCmdCnt = 0;
switch( priv->rf_chip )
{
case RF_8225:
if (!(channel >= 1 && channel <= 14))
{
RT_TRACE(COMP_ERR, "illegal channel for Zebra 8225: %d\n", channel);
return false;
}
rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
CmdID_RF_WriteReg, rZebra1_Channel, RF_CHANNEL_TABLE_ZEBRA[channel], 10);
rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
CmdID_End, 0, 0, 0);
break;
case RF_8256:
// TEST!! This is not the table for 8256!!
if (!(channel >= 1 && channel <= 14))
{
RT_TRACE(COMP_ERR, "illegal channel for Zebra 8256: %d\n", channel);
return false;
}
rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
CmdID_RF_WriteReg, rZebra1_Channel, channel, 10);
rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
CmdID_End, 0, 0, 0);
break;
case RF_8258:
break;
default:
RT_TRACE(COMP_ERR, "Unknown RFChipID: %d\n", priv->rf_chip);
return false;
break;
}
do{
switch(*stage)
{
case 0:
CurrentCmd=&PreCommonCmd[*step];
break;
case 1:
CurrentCmd=&RfDependCmd[*step];
break;
case 2:
CurrentCmd=&PostCommonCmd[*step];
break;
}
if(CurrentCmd->CmdID==CmdID_End)
{
if((*stage)==2)
{
return true;
}
else
{
(*stage)++;
(*step)=0;
continue;
}
}
switch(CurrentCmd->CmdID)
{
case CmdID_SetTxPowerLevel:
if(priv->card_8192_version > (u8)VERSION_8190_BD) //xiong: consider it later!
rtl8192_SetTxPowerLevel(dev,channel);
break;
case CmdID_WritePortUlong:
write_nic_dword(dev, CurrentCmd->Para1, CurrentCmd->Para2);
break;
case CmdID_WritePortUshort:
write_nic_word(dev, CurrentCmd->Para1, (u16)CurrentCmd->Para2);
break;
case CmdID_WritePortUchar:
write_nic_byte(dev, CurrentCmd->Para1, (u8)CurrentCmd->Para2);
break;
case CmdID_RF_WriteReg:
for(eRFPath = 0; eRFPath <priv->NumTotalRFPath; eRFPath++)
rtl8192_phy_SetRFReg(dev, (RF90_RADIO_PATH_E)eRFPath, CurrentCmd->Para1, bMask12Bits, CurrentCmd->Para2<<7);
break;
default:
break;
}
break;
}while(true);
}/*for(Number of RF paths)*/
(*delay)=CurrentCmd->msDelay;
(*step)++;
return false;
}
/******************************************************************************
*function: This function does acturally set channel work
* input: struct net_device *dev
* u8 channel
* output: none
* return: noin
* Note: We should not call this function directly
* ***************************************************************************/
static void rtl8192_phy_FinishSwChnlNow(struct net_device *dev, u8 channel)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 delay = 0;
while(!rtl8192_phy_SwChnlStepByStep(dev,channel,&priv->SwChnlStage,&priv->SwChnlStep,&delay))
{
if(delay>0)
msleep(delay);//or mdelay? need further consideration
if(!priv->up)
break;
}
}
/******************************************************************************
*function: Callback routine of the work item for switch channel.
* input:
*
* output: none
* return: noin
* ***************************************************************************/
void rtl8192_SwChnl_WorkItem(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
RT_TRACE(COMP_TRACE, "==> SwChnlCallback819xUsbWorkItem()\n");
RT_TRACE(COMP_TRACE, "=====>--%s(), set chan:%d, priv:%p\n", __FUNCTION__, priv->chan, priv);
rtl8192_phy_FinishSwChnlNow(dev , priv->chan);
RT_TRACE(COMP_TRACE, "<== SwChnlCallback819xUsbWorkItem()\n");
}
/******************************************************************************
*function: This function scheduled actural workitem to set channel
* input: net_device dev
* u8 channel //channel to set
* output: none
* return: return code show if workitem is scheduled(1:pass, 0:fail)
* Note: Delay may be required for RF configuration
* ***************************************************************************/
u8 rtl8192_phy_SwChnl(struct net_device* dev, u8 channel)
{
struct r8192_priv *priv = ieee80211_priv(dev);
RT_TRACE(COMP_PHY, "=====>%s()\n", __FUNCTION__);
if(!priv->up)
return false;
if(priv->SwChnlInProgress)
return false;
// if(pHalData->SetBWModeInProgress)
// return;
//--------------------------------------------
switch(priv->ieee80211->mode)
{
case WIRELESS_MODE_A:
case WIRELESS_MODE_N_5G:
if (channel<=14){
RT_TRACE(COMP_ERR, "WIRELESS_MODE_A but channel<=14");
return false;
}
break;
case WIRELESS_MODE_B:
if (channel>14){
RT_TRACE(COMP_ERR, "WIRELESS_MODE_B but channel>14");
return false;
}
break;
case WIRELESS_MODE_G:
case WIRELESS_MODE_N_24G:
if (channel>14){
RT_TRACE(COMP_ERR, "WIRELESS_MODE_G but channel>14");
return false;
}
break;
}
//--------------------------------------------
priv->SwChnlInProgress = true;
if(channel == 0)
channel = 1;
priv->chan=channel;
priv->SwChnlStage=0;
priv->SwChnlStep=0;
// schedule_work(&(priv->SwChnlWorkItem));
// rtl8192_SwChnl_WorkItem(dev);
if(priv->up) {
// queue_work(priv->priv_wq,&(priv->SwChnlWorkItem));
rtl8192_SwChnl_WorkItem(dev);
}
priv->SwChnlInProgress = false;
return true;
}
static void CCK_Tx_Power_Track_BW_Switch_TSSI(struct net_device *dev )
{
struct r8192_priv *priv = ieee80211_priv(dev);
switch(priv->CurrentChannelBW)
{
/* 20 MHz channel*/
case HT_CHANNEL_WIDTH_20:
//added by vivi, cck,tx power track, 20080703
priv->CCKPresentAttentuation =
priv->CCKPresentAttentuation_20Mdefault + priv->CCKPresentAttentuation_difference;
if(priv->CCKPresentAttentuation > (CCKTxBBGainTableLength-1))
priv->CCKPresentAttentuation = CCKTxBBGainTableLength-1;
if(priv->CCKPresentAttentuation < 0)
priv->CCKPresentAttentuation = 0;
RT_TRACE(COMP_POWER_TRACKING, "20M, priv->CCKPresentAttentuation = %d\n", priv->CCKPresentAttentuation);
if(priv->ieee80211->current_network.channel== 14 && !priv->bcck_in_ch14)
{
priv->bcck_in_ch14 = TRUE;
dm_cck_txpower_adjust(dev,priv->bcck_in_ch14);
}
else if(priv->ieee80211->current_network.channel != 14 && priv->bcck_in_ch14)
{
priv->bcck_in_ch14 = FALSE;
dm_cck_txpower_adjust(dev,priv->bcck_in_ch14);
}
else
dm_cck_txpower_adjust(dev,priv->bcck_in_ch14);
break;
/* 40 MHz channel*/
case HT_CHANNEL_WIDTH_20_40:
//added by vivi, cck,tx power track, 20080703
priv->CCKPresentAttentuation =
priv->CCKPresentAttentuation_40Mdefault + priv->CCKPresentAttentuation_difference;
RT_TRACE(COMP_POWER_TRACKING, "40M, priv->CCKPresentAttentuation = %d\n", priv->CCKPresentAttentuation);
if(priv->CCKPresentAttentuation > (CCKTxBBGainTableLength-1))
priv->CCKPresentAttentuation = CCKTxBBGainTableLength-1;
if(priv->CCKPresentAttentuation < 0)
priv->CCKPresentAttentuation = 0;
if(priv->ieee80211->current_network.channel == 14 && !priv->bcck_in_ch14)
{
priv->bcck_in_ch14 = TRUE;
dm_cck_txpower_adjust(dev,priv->bcck_in_ch14);
}
else if(priv->ieee80211->current_network.channel != 14 && priv->bcck_in_ch14)
{
priv->bcck_in_ch14 = FALSE;
dm_cck_txpower_adjust(dev,priv->bcck_in_ch14);
}
else
dm_cck_txpower_adjust(dev,priv->bcck_in_ch14);
break;
}
}
#ifndef RTL8190P
static void CCK_Tx_Power_Track_BW_Switch_ThermalMeter(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
if(priv->ieee80211->current_network.channel == 14 && !priv->bcck_in_ch14)
priv->bcck_in_ch14 = TRUE;
else if(priv->ieee80211->current_network.channel != 14 && priv->bcck_in_ch14)
priv->bcck_in_ch14 = FALSE;
//write to default index and tx power track will be done in dm.
switch(priv->CurrentChannelBW)
{
/* 20 MHz channel*/
case HT_CHANNEL_WIDTH_20:
if(priv->Record_CCK_20Mindex == 0)
priv->Record_CCK_20Mindex = 6; //set default value.
priv->CCK_index = priv->Record_CCK_20Mindex;//6;
RT_TRACE(COMP_POWER_TRACKING, "20MHz, CCK_Tx_Power_Track_BW_Switch_ThermalMeter(),CCK_index = %d\n", priv->CCK_index);
break;
/* 40 MHz channel*/
case HT_CHANNEL_WIDTH_20_40:
priv->CCK_index = priv->Record_CCK_40Mindex;//0;
RT_TRACE(COMP_POWER_TRACKING, "40MHz, CCK_Tx_Power_Track_BW_Switch_ThermalMeter(), CCK_index = %d\n", priv->CCK_index);
break;
}
dm_cck_txpower_adjust(dev, priv->bcck_in_ch14);
}
#endif
static void CCK_Tx_Power_Track_BW_Switch(struct net_device *dev)
{
#ifdef RTL8192E
struct r8192_priv *priv = ieee80211_priv(dev);
#endif
#ifdef RTL8190P
CCK_Tx_Power_Track_BW_Switch_TSSI(dev);
#else
//if(pHalData->bDcut == TRUE)
if(priv->IC_Cut >= IC_VersionCut_D)
CCK_Tx_Power_Track_BW_Switch_TSSI(dev);
else
CCK_Tx_Power_Track_BW_Switch_ThermalMeter(dev);
#endif
}
//
/******************************************************************************
*function: Callback routine of the work item for set bandwidth mode.
* input: struct net_device *dev
* HT_CHANNEL_WIDTH Bandwidth //20M or 40M
* HT_EXTCHNL_OFFSET Offset //Upper, Lower, or Don't care
* output: none
* return: none
* Note: I doubt whether SetBWModeInProgress flag is necessary as we can
* test whether current work in the queue or not.//do I?
* ***************************************************************************/
void rtl8192_SetBWModeWorkItem(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 regBwOpMode;
RT_TRACE(COMP_SWBW, "==>rtl8192_SetBWModeWorkItem() Switch to %s bandwidth\n", \
priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20?"20MHz":"40MHz")
if(priv->rf_chip== RF_PSEUDO_11N)
{
priv->SetBWModeInProgress= false;
return;
}
if(!priv->up)
{
priv->SetBWModeInProgress= false;
return;
}
//<1>Set MAC register
regBwOpMode = read_nic_byte(dev, BW_OPMODE);
switch(priv->CurrentChannelBW)
{
case HT_CHANNEL_WIDTH_20:
regBwOpMode |= BW_OPMODE_20MHZ;
// 2007/02/07 Mark by Emily becasue we have not verify whether this register works
write_nic_byte(dev, BW_OPMODE, regBwOpMode);
break;
case HT_CHANNEL_WIDTH_20_40:
regBwOpMode &= ~BW_OPMODE_20MHZ;
// 2007/02/07 Mark by Emily becasue we have not verify whether this register works
write_nic_byte(dev, BW_OPMODE, regBwOpMode);
break;
default:
RT_TRACE(COMP_ERR, "SetChannelBandwidth819xUsb(): unknown Bandwidth: %#X\n",priv->CurrentChannelBW);
break;
}
//<2>Set PHY related register
switch(priv->CurrentChannelBW)
{
case HT_CHANNEL_WIDTH_20:
// Add by Vivi 20071119
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bRFMOD, 0x0);
rtl8192_setBBreg(dev, rFPGA1_RFMOD, bRFMOD, 0x0);
// rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x00100000, 1);
// Correct the tx power for CCK rate in 20M. Suggest by YN, 20071207
// write_nic_dword(dev, rCCK0_TxFilter1, 0x1a1b0000);
// write_nic_dword(dev, rCCK0_TxFilter2, 0x090e1317);
// write_nic_dword(dev, rCCK0_DebugPort, 0x00000204);
if(!priv->btxpower_tracking)
{
write_nic_dword(dev, rCCK0_TxFilter1, 0x1a1b0000);
write_nic_dword(dev, rCCK0_TxFilter2, 0x090e1317);
write_nic_dword(dev, rCCK0_DebugPort, 0x00000204);
}
else
CCK_Tx_Power_Track_BW_Switch(dev);
#ifdef RTL8190P
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, bADClkPhase, 1);
rtl8192_setBBreg(dev, rOFDM0_RxDetector1, bMaskByte0, 0x44); // 0xc30 is for 8190 only, Emily
#else
#ifdef RTL8192E
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x00100000, 1);
#endif
#endif
break;
case HT_CHANNEL_WIDTH_20_40:
// Add by Vivi 20071119
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bRFMOD, 0x1);
rtl8192_setBBreg(dev, rFPGA1_RFMOD, bRFMOD, 0x1);
//rtl8192_setBBreg(dev, rCCK0_System, bCCKSideBand, (priv->nCur40MhzPrimeSC>>1));
//rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x00100000, 0);
//rtl8192_setBBreg(dev, rOFDM1_LSTF, 0xC00, priv->nCur40MhzPrimeSC);
// Correct the tx power for CCK rate in 40M. Suggest by YN, 20071207
//write_nic_dword(dev, rCCK0_TxFilter1, 0x35360000);
//write_nic_dword(dev, rCCK0_TxFilter2, 0x121c252e);
//write_nic_dword(dev, rCCK0_DebugPort, 0x00000409);
if(!priv->btxpower_tracking)
{
write_nic_dword(dev, rCCK0_TxFilter1, 0x35360000);
write_nic_dword(dev, rCCK0_TxFilter2, 0x121c252e);
write_nic_dword(dev, rCCK0_DebugPort, 0x00000409);
}
else
CCK_Tx_Power_Track_BW_Switch(dev);
// Set Control channel to upper or lower. These settings are required only for 40MHz
rtl8192_setBBreg(dev, rCCK0_System, bCCKSideBand, (priv->nCur40MhzPrimeSC>>1));
rtl8192_setBBreg(dev, rOFDM1_LSTF, 0xC00, priv->nCur40MhzPrimeSC);
#ifdef RTL8190P
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, bADClkPhase, 0);
rtl8192_setBBreg(dev, rOFDM0_RxDetector1, bMaskByte0, 0x42); // 0xc30 is for 8190 only, Emily
// Set whether CCK should be sent in upper or lower channel. Suggest by YN. 20071207
// It is set in Tx descriptor for 8192x series
if(priv->nCur40MhzPrimeSC == HAL_PRIME_CHNL_OFFSET_UPPER)
{
rtl8192_setBBreg(dev, rFPGA0_RFMOD, (BIT6|BIT5), 0x01);
}else if(priv->nCur40MhzPrimeSC == HAL_PRIME_CHNL_OFFSET_LOWER)
{
rtl8192_setBBreg(dev, rFPGA0_RFMOD, (BIT6|BIT5), 0x02);
}
#else
#ifdef RTL8192E
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x00100000, 0);
#endif
#endif
break;
default:
RT_TRACE(COMP_ERR, "SetChannelBandwidth819xUsb(): unknown Bandwidth: %#X\n" ,priv->CurrentChannelBW);
break;
}
//Skip over setting of J-mode in BB register here. Default value is "None J mode". Emily 20070315
#if 1
//<3>Set RF related register
switch( priv->rf_chip )
{
case RF_8225:
#ifdef TO_DO_LIST
PHY_SetRF8225Bandwidth(Adapter, pHalData->CurrentChannelBW);
#endif
break;
case RF_8256:
PHY_SetRF8256Bandwidth(dev, priv->CurrentChannelBW);
break;
case RF_8258:
// PHY_SetRF8258Bandwidth();
break;
case RF_PSEUDO_11N:
// Do Nothing
break;
default:
RT_TRACE(COMP_ERR, "Unknown RFChipID: %d\n", priv->rf_chip);
break;
}
#endif
atomic_dec(&(priv->ieee80211->atm_swbw));
priv->SetBWModeInProgress= false;
RT_TRACE(COMP_SWBW, "<==SetBWMode819xUsb()");
}
/******************************************************************************
*function: This function schedules bandwith switch work.
* input: struct net_device *dev
* HT_CHANNEL_WIDTH Bandwidth //20M or 40M
* HT_EXTCHNL_OFFSET Offset //Upper, Lower, or Don't care
* output: none
* return: none
* Note: I doubt whether SetBWModeInProgress flag is necessary as we can
* test whether current work in the queue or not.//do I?
* ***************************************************************************/
void rtl8192_SetBWMode(struct net_device *dev, HT_CHANNEL_WIDTH Bandwidth, HT_EXTCHNL_OFFSET Offset)
{
struct r8192_priv *priv = ieee80211_priv(dev);
if(priv->SetBWModeInProgress)
return;
atomic_inc(&(priv->ieee80211->atm_swbw));
priv->SetBWModeInProgress= true;
priv->CurrentChannelBW = Bandwidth;
if(Offset==HT_EXTCHNL_OFFSET_LOWER)
priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_UPPER;
else if(Offset==HT_EXTCHNL_OFFSET_UPPER)
priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_LOWER;
else
priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_DONT_CARE;
//queue_work(priv->priv_wq, &(priv->SetBWModeWorkItem));
// schedule_work(&(priv->SetBWModeWorkItem));
rtl8192_SetBWModeWorkItem(dev);
}
void InitialGain819xPci(struct net_device *dev, u8 Operation)
{
#define SCAN_RX_INITIAL_GAIN 0x17
#define POWER_DETECTION_TH 0x08
struct r8192_priv *priv = ieee80211_priv(dev);
u32 BitMask;
u8 initial_gain;
if(priv->up)
{
switch(Operation)
{
case IG_Backup:
RT_TRACE(COMP_SCAN, "IG_Backup, backup the initial gain.\n");
initial_gain = SCAN_RX_INITIAL_GAIN;//pHalData->DefaultInitialGain[0];//
BitMask = bMaskByte0;
if(dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM)
rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x8); // FW DIG OFF
priv->initgain_backup.xaagccore1 = (u8)rtl8192_QueryBBReg(dev, rOFDM0_XAAGCCore1, BitMask);
priv->initgain_backup.xbagccore1 = (u8)rtl8192_QueryBBReg(dev, rOFDM0_XBAGCCore1, BitMask);
priv->initgain_backup.xcagccore1 = (u8)rtl8192_QueryBBReg(dev, rOFDM0_XCAGCCore1, BitMask);
priv->initgain_backup.xdagccore1 = (u8)rtl8192_QueryBBReg(dev, rOFDM0_XDAGCCore1, BitMask);
BitMask = bMaskByte2;
priv->initgain_backup.cca = (u8)rtl8192_QueryBBReg(dev, rCCK0_CCA, BitMask);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc50 is %x\n",priv->initgain_backup.xaagccore1);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc58 is %x\n",priv->initgain_backup.xbagccore1);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc60 is %x\n",priv->initgain_backup.xcagccore1);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc68 is %x\n",priv->initgain_backup.xdagccore1);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xa0a is %x\n",priv->initgain_backup.cca);
RT_TRACE(COMP_SCAN, "Write scan initial gain = 0x%x \n", initial_gain);
write_nic_byte(dev, rOFDM0_XAAGCCore1, initial_gain);
write_nic_byte(dev, rOFDM0_XBAGCCore1, initial_gain);
write_nic_byte(dev, rOFDM0_XCAGCCore1, initial_gain);
write_nic_byte(dev, rOFDM0_XDAGCCore1, initial_gain);
RT_TRACE(COMP_SCAN, "Write scan 0xa0a = 0x%x \n", POWER_DETECTION_TH);
write_nic_byte(dev, 0xa0a, POWER_DETECTION_TH);
break;
case IG_Restore:
RT_TRACE(COMP_SCAN, "IG_Restore, restore the initial gain.\n");
BitMask = 0x7f; //Bit0~ Bit6
if(dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM)
rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x8); // FW DIG OFF
rtl8192_setBBreg(dev, rOFDM0_XAAGCCore1, BitMask, (u32)priv->initgain_backup.xaagccore1);
rtl8192_setBBreg(dev, rOFDM0_XBAGCCore1, BitMask, (u32)priv->initgain_backup.xbagccore1);
rtl8192_setBBreg(dev, rOFDM0_XCAGCCore1, BitMask, (u32)priv->initgain_backup.xcagccore1);
rtl8192_setBBreg(dev, rOFDM0_XDAGCCore1, BitMask, (u32)priv->initgain_backup.xdagccore1);
BitMask = bMaskByte2;
rtl8192_setBBreg(dev, rCCK0_CCA, BitMask, (u32)priv->initgain_backup.cca);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc50 is %x\n",priv->initgain_backup.xaagccore1);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc58 is %x\n",priv->initgain_backup.xbagccore1);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc60 is %x\n",priv->initgain_backup.xcagccore1);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc68 is %x\n",priv->initgain_backup.xdagccore1);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xa0a is %x\n",priv->initgain_backup.cca);
rtl8192_phy_setTxPower(dev,priv->ieee80211->current_network.channel);
if(dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM)
rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x1); // FW DIG ON
break;
default:
RT_TRACE(COMP_SCAN, "Unknown IG Operation. \n");
break;
}
}
}