swh:1:snp:32555a3fd8878f019c2ebd6c964bc1edcaeff337
Tip revision: 39403865d2e4590802553370a56c9ab93131e4ee authored by Linus Torvalds on 13 May 2007, 01:45:56 UTC
Linux 2.6.22-rc1
Linux 2.6.22-rc1
Tip revision: 3940386
CommonIO
S/390 common I/O-Layer - command line parameters and /proc entries
==================================================================
Command line parameters
-----------------------
* cio_msg = yes | no
Determines whether information on found devices and sensed device
characteristics should be shown during startup, i. e. messages of the types
"Detected device 0.0.4711 on subchannel 0.0.0042" and "SenseID: Device
0.0.4711 reports: ...".
Default is off.
* cio_ignore = {all} |
{<device> | <range of devices>} |
{!<device> | !<range of devices>}
The given devices will be ignored by the common I/O-layer; no detection
and device sensing will be done on any of those devices. The subchannel to
which the device in question is attached will be treated as if no device was
attached.
An ignored device can be un-ignored later; see the "/proc entries"-section for
details.
The devices must be given either as bus ids (0.0.abcd) or as hexadecimal
device numbers (0xabcd or abcd, for 2.4 backward compatibility).
You can use the 'all' keyword to ignore all devices.
The '!' operator will cause the I/O-layer to _not_ ignore a device.
The command line is parsed from left to right.
For example,
cio_ignore=0.0.0023-0.0.0042,0.0.4711
will ignore all devices ranging from 0.0.0023 to 0.0.0042 and the device
0.0.4711, if detected.
As another example,
cio_ignore=all,!0.0.4711,!0.0.fd00-0.0.fd02
will ignore all devices but 0.0.4711, 0.0.fd00, 0.0.fd01, 0.0.fd02.
By default, no devices are ignored.
/proc entries
-------------
* /proc/cio_ignore
Lists the ranges of devices (by bus id) which are ignored by common I/O.
You can un-ignore certain or all devices by piping to /proc/cio_ignore.
"free all" will un-ignore all ignored devices,
"free <device range>, <device range>, ..." will un-ignore the specified
devices.
For example, if devices 0.0.0023 to 0.0.0042 and 0.0.4711 are ignored,
- echo free 0.0.0030-0.0.0032 > /proc/cio_ignore
will un-ignore devices 0.0.0030 to 0.0.0032 and will leave devices 0.0.0023
to 0.0.002f, 0.0.0033 to 0.0.0042 and 0.0.4711 ignored;
- echo free 0.0.0041 > /proc/cio_ignore will furthermore un-ignore device
0.0.0041;
- echo free all > /proc/cio_ignore will un-ignore all remaining ignored
devices.
When a device is un-ignored, device recognition and sensing is performed and
the device driver will be notified if possible, so the device will become
available to the system. Note that un-ignoring is performed asynchronously.
You can also add ranges of devices to be ignored by piping to
/proc/cio_ignore; "add <device range>, <device range>, ..." will ignore the
specified devices.
Note: While already known devices can be added to the list of devices to be
ignored, there will be no effect on then. However, if such a device
disappears and then reappears, it will then be ignored.
For example,
"echo add 0.0.a000-0.0.accc, 0.0.af00-0.0.afff > /proc/cio_ignore"
will add 0.0.a000-0.0.accc and 0.0.af00-0.0.afff to the list of ignored
devices.
The devices can be specified either by bus id (0.0.abcd) or, for 2.4 backward
compatibility, by the device number in hexadecimal (0xabcd or abcd).
* /proc/s390dbf/cio_*/ (S/390 debug feature)
Some views generated by the debug feature to hold various debug outputs.
- /proc/s390dbf/cio_crw/sprintf
Messages from the processing of pending channel report words (machine check
handling), which will also show when CONFIG_DEBUG_CRW is defined.
- /proc/s390dbf/cio_msg/sprintf
Various debug messages from the common I/O-layer; generally, messages which
will also show when CONFIG_DEBUG_IO is defined.
- /proc/s390dbf/cio_trace/hex_ascii
Logs the calling of functions in the common I/O-layer and, if applicable,
which subchannel they were called for, as well as dumps of some data
structures (like irb in an error case).
The level of logging can be changed to be more or less verbose by piping to
/proc/s390dbf/cio_*/level a number between 0 and 6; see the documentation on
the S/390 debug feature (Documentation/s390/s390dbf.txt) for details.
* For some of the information present in the /proc filesystem in 2.4 (namely,
/proc/subchannels and /proc/chpids), see driver-model.txt.
Information formerly in /proc/irq_count is now in /proc/interrupts.