swh:1:snp:32555a3fd8878f019c2ebd6c964bc1edcaeff337
Tip revision: bbf5c979011a099af5dc76498918ed7df445635b authored by Linus Torvalds on 11 October 2020, 21:15:50 UTC
Linux 5.9
Linux 5.9
Tip revision: bbf5c97
opp2430_data.c
// SPDX-License-Identifier: GPL-2.0
/*
* opp2430_data.c - old-style "OPP" table for OMAP2430
*
* Copyright (C) 2005-2009 Texas Instruments, Inc.
* Copyright (C) 2004-2009 Nokia Corporation
*
* Richard Woodruff <r-woodruff2@ti.com>
*
* The OMAP2 processor can be run at several discrete 'PRCM configurations'.
* These configurations are characterized by voltage and speed for clocks.
* The device is only validated for certain combinations. One way to express
* these combinations is via the 'ratios' which the clocks operate with
* respect to each other. These ratio sets are for a given voltage/DPLL
* setting. All configurations can be described by a DPLL setting and a ratio.
*
* 2430 differs from 2420 in that there are no more phase synchronizers used.
* They both have a slightly different clock domain setup. 2420(iva1,dsp) vs
* 2430 (iva2.1, NOdsp, mdm)
*
* XXX Missing voltage data.
* XXX Missing 19.2MHz sys_clk rate sets.
*
* THe format described in this file is deprecated. Once a reasonable
* OPP API exists, the data in this file should be converted to use it.
*
* This is technically part of the OMAP2xxx clock code.
*/
#include <linux/kernel.h>
#include "opp2xxx.h"
#include "sdrc.h"
#include "clock.h"
/*
* Key dividers which make up a PRCM set. Ratios for a PRCM are mandated.
* xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,
* CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL,
* CM_CLKSEL2_PLL, CM_CLKSEL_MDM
*
* Filling in table based on 2430-SDPs variants available. There are
* quite a few more rate combinations which could be defined.
*
* When multiple values are defined the start up will try and choose
* the fastest one. If a 'fast' value is defined, then automatically,
* the /2 one should be included as it can be used. Generally having
* more than one fast set does not make sense, as static timings need
* to be changed to change the set. The exception is the bypass
* setting which is available for low power bypass.
*
* Note: This table needs to be sorted, fastest to slowest.
*/
const struct prcm_config omap2430_rate_table[] = {
/* PRCM #4 - ratio2 (ES2.1) - FAST */
{S13M, S798M, S399M, R2_CM_CLKSEL_MPU_VAL, /* 399MHz ARM */
R2_CM_CLKSEL_DSP_VAL, R2_CM_CLKSEL_GFX_VAL,
R2_CM_CLKSEL1_CORE_VAL, M4_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_2x_VAL, R2_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_133MHz,
RATE_IN_243X},
/* PRCM #2 - ratio1 (ES2) - FAST */
{S13M, S658M, S329M, R1_CM_CLKSEL_MPU_VAL, /* 330MHz ARM */
R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
R1_CM_CLKSEL1_CORE_VAL, M2_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_165MHz,
RATE_IN_243X},
/* PRCM #5a - ratio1 - FAST */
{S13M, S532M, S266M, R1_CM_CLKSEL_MPU_VAL, /* 266MHz ARM */
R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
R1_CM_CLKSEL1_CORE_VAL, M5A_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_133MHz,
RATE_IN_243X},
/* PRCM #5b - ratio1 - FAST */
{S13M, S400M, S200M, R1_CM_CLKSEL_MPU_VAL, /* 200MHz ARM */
R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
R1_CM_CLKSEL1_CORE_VAL, M5B_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_100MHz,
RATE_IN_243X},
/* PRCM #4 - ratio1 (ES2.1) - SLOW */
{S13M, S399M, S199M, R2_CM_CLKSEL_MPU_VAL, /* 200MHz ARM */
R2_CM_CLKSEL_DSP_VAL, R2_CM_CLKSEL_GFX_VAL,
R2_CM_CLKSEL1_CORE_VAL, M4_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_1x_VAL, R2_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_133MHz,
RATE_IN_243X},
/* PRCM #2 - ratio1 (ES2) - SLOW */
{S13M, S329M, S164M, R1_CM_CLKSEL_MPU_VAL, /* 165MHz ARM */
R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
R1_CM_CLKSEL1_CORE_VAL, M2_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_165MHz,
RATE_IN_243X},
/* PRCM #5a - ratio1 - SLOW */
{S13M, S266M, S133M, R1_CM_CLKSEL_MPU_VAL, /* 133MHz ARM */
R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
R1_CM_CLKSEL1_CORE_VAL, M5A_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_133MHz,
RATE_IN_243X},
/* PRCM #5b - ratio1 - SLOW*/
{S13M, S200M, S100M, R1_CM_CLKSEL_MPU_VAL, /* 100MHz ARM */
R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL,
R1_CM_CLKSEL1_CORE_VAL, M5B_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_100MHz,
RATE_IN_243X},
/* PRCM-boot/bypass */
{S13M, S13M, S13M, RB_CM_CLKSEL_MPU_VAL, /* 13MHz */
RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL,
RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_13_VAL,
MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_BYPASS,
RATE_IN_243X},
/* PRCM-boot/bypass */
{S12M, S12M, S12M, RB_CM_CLKSEL_MPU_VAL, /* 12MHz */
RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL,
RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_12_VAL,
MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL,
SDRC_RFR_CTRL_BYPASS,
RATE_IN_243X},
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},
};