swh:1:snp:32555a3fd8878f019c2ebd6c964bc1edcaeff337
Tip revision: 0ee5623f9a6e52df90a78bd21179f8ab370e102e authored by Linus Torvalds on 04 May 2011, 02:59:13 UTC
Linux 2.6.39-rc6
Linux 2.6.39-rc6
Tip revision: 0ee5623
Kconfig
# Copyright 2007 Simtec Electronics
#
# Licensed under GPLv2
config CPU_S3C2410
bool
depends on ARCH_S3C2410
select CPU_ARM920T
select S3C_GPIO_PULL_UP
select S3C2410_CLOCK
select S3C2410_GPIO
select CPU_LLSERIAL_S3C2410
select S3C2410_PM if PM
select S3C2410_CPUFREQ if CPU_FREQ_S3C24XX
help
Support for S3C2410 and S3C2410A family from the S3C24XX line
of Samsung Mobile CPUs.
config CPU_S3C2410_DMA
bool
depends on S3C2410_DMA && (CPU_S3C2410 || CPU_S3C2442)
default y if CPU_S3C2410 || CPU_S3C2442
help
DMA device selection for S3C2410 and compatible CPUs
config S3C2410_PM
bool
help
Power Management code common to S3C2410 and better
config S3C2410_GPIO
bool
help
GPIO code for S3C2410 and similar processors
config SIMTEC_NOR
bool
help
Internal node to specify machine has simtec NOR mapping
config MACH_BAST_IDE
bool
select HAVE_PATA_PLATFORM
help
Internal node for machines with an BAST style IDE
interface
# cpu frequency scaling support
config S3C2410_CPUFREQ
bool
depends on CPU_FREQ_S3C24XX && CPU_S3C2410
select S3C2410_CPUFREQ_UTILS
help
CPU Frequency scaling support for S3C2410
config S3C2410_PLLTABLE
bool
depends on S3C2410_CPUFREQ && CPU_FREQ_S3C24XX_PLL
default y
help
Select the PLL table for the S3C2410
menu "S3C2410 Machines"
config ARCH_SMDK2410
bool "SMDK2410/A9M2410"
select CPU_S3C2410
select MACH_SMDK
help
Say Y here if you are using the SMDK2410 or the derived module A9M2410
<http://www.fsforth.de>
config ARCH_H1940
bool "IPAQ H1940"
select CPU_S3C2410
select PM_H1940 if PM
select S3C_DEV_USB_HOST
select S3C_DEV_NAND
select S3C2410_SETUP_TS
help
Say Y here if you are using the HP IPAQ H1940
config H1940BT
tristate "Control the state of H1940 bluetooth chip"
depends on ARCH_H1940
select RFKILL
help
This is a simple driver that is able to control
the state of built in bluetooth chip on h1940.
config PM_H1940
bool
help
Internal node for H1940 and related PM
config MACH_N30
bool "Acer N30 family"
select CPU_S3C2410
select MACH_N35
select S3C_DEV_USB_HOST
select S3C_DEV_NAND
help
Say Y here if you want suppt for the Acer N30, Acer N35,
Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs.
config MACH_N35
bool
help
Internal node in order to enable support for Acer N35 if Acer N30 is
selected.
config ARCH_BAST
bool "Simtec Electronics BAST (EB2410ITX)"
select CPU_S3C2410
select S3C2410_IOTIMING if S3C2410_CPUFREQ
select PM_SIMTEC if PM
select SIMTEC_NOR
select MACH_BAST_IDE
select S3C24XX_DCLK
select ISA
select S3C_DEV_HWMON
select S3C_DEV_USB_HOST
select S3C_DEV_NAND
help
Say Y here if you are using the Simtec Electronics EB2410ITX
development board (also known as BAST)
config MACH_OTOM
bool "NexVision OTOM Board"
select CPU_S3C2410
select S3C_DEV_USB_HOST
select S3C_DEV_NAND
help
Say Y here if you are using the Nex Vision OTOM board
config MACH_AML_M5900
bool "AML M5900 Series"
select CPU_S3C2410
select PM_SIMTEC if PM
select S3C_DEV_USB_HOST
help
Say Y here if you are using the American Microsystems M5900 Series
<http://www.amltd.com>
config BAST_PC104_IRQ
bool "BAST PC104 IRQ support"
depends on ARCH_BAST
default y
help
Say Y here to enable the PC104 IRQ routing on the
Simtec BAST (EB2410ITX)
config MACH_TCT_HAMMER
bool "TCT Hammer Board"
select CPU_S3C2410
select S3C_DEV_USB_HOST
help
Say Y here if you are using the TinCanTools Hammer Board
<http://www.tincantools.com>
config MACH_VR1000
bool "Thorcom VR1000"
select PM_SIMTEC if PM
select S3C24XX_DCLK
select SIMTEC_NOR
select MACH_BAST_IDE
select CPU_S3C2410
select S3C_DEV_USB_HOST
help
Say Y here if you are using the Thorcom VR1000 board.
config MACH_QT2410
bool "QT2410"
select CPU_S3C2410
select S3C_DEV_USB_HOST
select S3C_DEV_NAND
help
Say Y here if you are using the Armzone QT2410
endmenu