swh:1:snp:32555a3fd8878f019c2ebd6c964bc1edcaeff337
Tip revision: 02da2d72174c61988eb4456b53f405e3ebdebce4 authored by Linus Torvalds on 24 April 2016, 23:17:05 UTC
Linux 4.6-rc5
Linux 4.6-rc5
Tip revision: 02da2d7
cciss.h
#ifndef CCISS_H
#define CCISS_H
#include <linux/genhd.h>
#include <linux/mutex.h>
#include "cciss_cmd.h"
#define NWD_SHIFT 4
#define MAX_PART (1 << NWD_SHIFT)
#define IO_OK 0
#define IO_ERROR 1
#define IO_NEEDS_RETRY 3
#define VENDOR_LEN 8
#define MODEL_LEN 16
#define REV_LEN 4
struct ctlr_info;
typedef struct ctlr_info ctlr_info_t;
struct access_method {
void (*submit_command)(ctlr_info_t *h, CommandList_struct *c);
void (*set_intr_mask)(ctlr_info_t *h, unsigned long val);
unsigned long (*fifo_full)(ctlr_info_t *h);
bool (*intr_pending)(ctlr_info_t *h);
unsigned long (*command_completed)(ctlr_info_t *h);
};
typedef struct _drive_info_struct
{
unsigned char LunID[8];
int usage_count;
struct request_queue *queue;
sector_t nr_blocks;
int block_size;
int heads;
int sectors;
int cylinders;
int raid_level; /* set to -1 to indicate that
* the drive is not in use/configured
*/
int busy_configuring; /* This is set when a drive is being removed
* to prevent it from being opened or it's
* queue from being started.
*/
struct device dev;
__u8 serial_no[16]; /* from inquiry page 0x83,
* not necc. null terminated.
*/
char vendor[VENDOR_LEN + 1]; /* SCSI vendor string */
char model[MODEL_LEN + 1]; /* SCSI model string */
char rev[REV_LEN + 1]; /* SCSI revision string */
char device_initialized; /* indicates whether dev is initialized */
} drive_info_struct;
struct ctlr_info
{
int ctlr;
char devname[8];
char *product_name;
char firm_ver[4]; /* Firmware version */
struct pci_dev *pdev;
__u32 board_id;
void __iomem *vaddr;
unsigned long paddr;
int nr_cmds; /* Number of commands allowed on this controller */
CfgTable_struct __iomem *cfgtable;
int interrupts_enabled;
int major;
int max_commands;
int commands_outstanding;
int max_outstanding; /* Debug */
int num_luns;
int highest_lun;
int usage_count; /* number of opens all all minor devices */
/* Need space for temp sg list
* number of scatter/gathers supported
* number of scatter/gathers in chained block
*/
struct scatterlist **scatter_list;
int maxsgentries;
int chainsize;
int max_cmd_sgentries;
SGDescriptor_struct **cmd_sg_list;
# define PERF_MODE_INT 0
# define DOORBELL_INT 1
# define SIMPLE_MODE_INT 2
# define MEMQ_MODE_INT 3
unsigned int intr[4];
unsigned int msix_vector;
unsigned int msi_vector;
int intr_mode;
int cciss_max_sectors;
BYTE cciss_read;
BYTE cciss_write;
BYTE cciss_read_capacity;
/* information about each logical volume */
drive_info_struct *drv[CISS_MAX_LUN];
struct access_method access;
/* queue and queue Info */
struct list_head reqQ;
struct list_head cmpQ;
unsigned int Qdepth;
unsigned int maxQsinceinit;
unsigned int maxSG;
spinlock_t lock;
/* pointers to command and error info pool */
CommandList_struct *cmd_pool;
dma_addr_t cmd_pool_dhandle;
ErrorInfo_struct *errinfo_pool;
dma_addr_t errinfo_pool_dhandle;
unsigned long *cmd_pool_bits;
int nr_allocs;
int nr_frees;
int busy_configuring;
int busy_initializing;
int busy_scanning;
struct mutex busy_shutting_down;
/* This element holds the zero based queue number of the last
* queue to be started. It is used for fairness.
*/
int next_to_run;
/* Disk structures we need to pass back */
struct gendisk *gendisk[CISS_MAX_LUN];
#ifdef CONFIG_CISS_SCSI_TAPE
struct cciss_scsi_adapter_data_t *scsi_ctlr;
#endif
unsigned char alive;
struct list_head scan_list;
struct completion scan_wait;
struct device dev;
/*
* Performant mode tables.
*/
u32 trans_support;
u32 trans_offset;
struct TransTable_struct *transtable;
unsigned long transMethod;
/*
* Performant mode completion buffer
*/
u64 *reply_pool;
dma_addr_t reply_pool_dhandle;
u64 *reply_pool_head;
size_t reply_pool_size;
unsigned char reply_pool_wraparound;
u32 *blockFetchTable;
};
/* Defining the diffent access_methods
*
* Memory mapped FIFO interface (SMART 53xx cards)
*/
#define SA5_DOORBELL 0x20
#define SA5_REQUEST_PORT_OFFSET 0x40
#define SA5_REPLY_INTR_MASK_OFFSET 0x34
#define SA5_REPLY_PORT_OFFSET 0x44
#define SA5_INTR_STATUS 0x30
#define SA5_SCRATCHPAD_OFFSET 0xB0
#define SA5_CTCFG_OFFSET 0xB4
#define SA5_CTMEM_OFFSET 0xB8
#define SA5_INTR_OFF 0x08
#define SA5B_INTR_OFF 0x04
#define SA5_INTR_PENDING 0x08
#define SA5B_INTR_PENDING 0x04
#define FIFO_EMPTY 0xffffffff
#define CCISS_FIRMWARE_READY 0xffff0000 /* value in scratchpad register */
/* Perf. mode flags */
#define SA5_PERF_INTR_PENDING 0x04
#define SA5_PERF_INTR_OFF 0x05
#define SA5_OUTDB_STATUS_PERF_BIT 0x01
#define SA5_OUTDB_CLEAR_PERF_BIT 0x01
#define SA5_OUTDB_CLEAR 0xA0
#define SA5_OUTDB_CLEAR_PERF_BIT 0x01
#define SA5_OUTDB_STATUS 0x9C
#define CISS_ERROR_BIT 0x02
#define CCISS_INTR_ON 1
#define CCISS_INTR_OFF 0
/* CCISS_BOARD_READY_WAIT_SECS is how long to wait for a board
* to become ready, in seconds, before giving up on it.
* CCISS_BOARD_READY_POLL_INTERVAL_MSECS * is how long to wait
* between polling the board to see if it is ready, in
* milliseconds. CCISS_BOARD_READY_ITERATIONS is derived
* the above.
*/
#define CCISS_BOARD_READY_WAIT_SECS (120)
#define CCISS_BOARD_NOT_READY_WAIT_SECS (100)
#define CCISS_BOARD_READY_POLL_INTERVAL_MSECS (100)
#define CCISS_BOARD_READY_ITERATIONS \
((CCISS_BOARD_READY_WAIT_SECS * 1000) / \
CCISS_BOARD_READY_POLL_INTERVAL_MSECS)
#define CCISS_BOARD_NOT_READY_ITERATIONS \
((CCISS_BOARD_NOT_READY_WAIT_SECS * 1000) / \
CCISS_BOARD_READY_POLL_INTERVAL_MSECS)
#define CCISS_POST_RESET_PAUSE_MSECS (3000)
#define CCISS_POST_RESET_NOOP_INTERVAL_MSECS (4000)
#define CCISS_POST_RESET_NOOP_RETRIES (12)
#define CCISS_POST_RESET_NOOP_TIMEOUT_MSECS (10000)
/*
Send the command to the hardware
*/
static void SA5_submit_command( ctlr_info_t *h, CommandList_struct *c)
{
#ifdef CCISS_DEBUG
printk(KERN_WARNING "cciss%d: Sending %08x - down to controller\n",
h->ctlr, c->busaddr);
#endif /* CCISS_DEBUG */
writel(c->busaddr, h->vaddr + SA5_REQUEST_PORT_OFFSET);
readl(h->vaddr + SA5_SCRATCHPAD_OFFSET);
h->commands_outstanding++;
if ( h->commands_outstanding > h->max_outstanding)
h->max_outstanding = h->commands_outstanding;
}
/*
* This card is the opposite of the other cards.
* 0 turns interrupts on...
* 0x08 turns them off...
*/
static void SA5_intr_mask(ctlr_info_t *h, unsigned long val)
{
if (val)
{ /* Turn interrupts on */
h->interrupts_enabled = 1;
writel(0, h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
} else /* Turn them off */
{
h->interrupts_enabled = 0;
writel( SA5_INTR_OFF,
h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
}
}
/*
* This card is the opposite of the other cards.
* 0 turns interrupts on...
* 0x04 turns them off...
*/
static void SA5B_intr_mask(ctlr_info_t *h, unsigned long val)
{
if (val)
{ /* Turn interrupts on */
h->interrupts_enabled = 1;
writel(0, h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
} else /* Turn them off */
{
h->interrupts_enabled = 0;
writel( SA5B_INTR_OFF,
h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
}
}
/* Performant mode intr_mask */
static void SA5_performant_intr_mask(ctlr_info_t *h, unsigned long val)
{
if (val) { /* turn on interrupts */
h->interrupts_enabled = 1;
writel(0, h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
} else {
h->interrupts_enabled = 0;
writel(SA5_PERF_INTR_OFF,
h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
(void) readl(h->vaddr + SA5_REPLY_INTR_MASK_OFFSET);
}
}
/*
* Returns true if fifo is full.
*
*/
static unsigned long SA5_fifo_full(ctlr_info_t *h)
{
if( h->commands_outstanding >= h->max_commands)
return(1);
else
return(0);
}
/*
* returns value read from hardware.
* returns FIFO_EMPTY if there is nothing to read
*/
static unsigned long SA5_completed(ctlr_info_t *h)
{
unsigned long register_value
= readl(h->vaddr + SA5_REPLY_PORT_OFFSET);
if(register_value != FIFO_EMPTY)
{
h->commands_outstanding--;
#ifdef CCISS_DEBUG
printk("cciss: Read %lx back from board\n", register_value);
#endif /* CCISS_DEBUG */
}
#ifdef CCISS_DEBUG
else
{
printk("cciss: FIFO Empty read\n");
}
#endif
return ( register_value);
}
/* Performant mode command completed */
static unsigned long SA5_performant_completed(ctlr_info_t *h)
{
unsigned long register_value = FIFO_EMPTY;
/* flush the controller write of the reply queue by reading
* outbound doorbell status register.
*/
register_value = readl(h->vaddr + SA5_OUTDB_STATUS);
/* msi auto clears the interrupt pending bit. */
if (!(h->msi_vector || h->msix_vector)) {
writel(SA5_OUTDB_CLEAR_PERF_BIT, h->vaddr + SA5_OUTDB_CLEAR);
/* Do a read in order to flush the write to the controller
* (as per spec.)
*/
register_value = readl(h->vaddr + SA5_OUTDB_STATUS);
}
if ((*(h->reply_pool_head) & 1) == (h->reply_pool_wraparound)) {
register_value = *(h->reply_pool_head);
(h->reply_pool_head)++;
h->commands_outstanding--;
} else {
register_value = FIFO_EMPTY;
}
/* Check for wraparound */
if (h->reply_pool_head == (h->reply_pool + h->max_commands)) {
h->reply_pool_head = h->reply_pool;
h->reply_pool_wraparound ^= 1;
}
return register_value;
}
/*
* Returns true if an interrupt is pending..
*/
static bool SA5_intr_pending(ctlr_info_t *h)
{
unsigned long register_value =
readl(h->vaddr + SA5_INTR_STATUS);
#ifdef CCISS_DEBUG
printk("cciss: intr_pending %lx\n", register_value);
#endif /* CCISS_DEBUG */
if( register_value & SA5_INTR_PENDING)
return 1;
return 0 ;
}
/*
* Returns true if an interrupt is pending..
*/
static bool SA5B_intr_pending(ctlr_info_t *h)
{
unsigned long register_value =
readl(h->vaddr + SA5_INTR_STATUS);
#ifdef CCISS_DEBUG
printk("cciss: intr_pending %lx\n", register_value);
#endif /* CCISS_DEBUG */
if( register_value & SA5B_INTR_PENDING)
return 1;
return 0 ;
}
static bool SA5_performant_intr_pending(ctlr_info_t *h)
{
unsigned long register_value = readl(h->vaddr + SA5_INTR_STATUS);
if (!register_value)
return false;
if (h->msi_vector || h->msix_vector)
return true;
/* Read outbound doorbell to flush */
register_value = readl(h->vaddr + SA5_OUTDB_STATUS);
return register_value & SA5_OUTDB_STATUS_PERF_BIT;
}
static struct access_method SA5_access = {
SA5_submit_command,
SA5_intr_mask,
SA5_fifo_full,
SA5_intr_pending,
SA5_completed,
};
static struct access_method SA5B_access = {
SA5_submit_command,
SA5B_intr_mask,
SA5_fifo_full,
SA5B_intr_pending,
SA5_completed,
};
static struct access_method SA5_performant_access = {
SA5_submit_command,
SA5_performant_intr_mask,
SA5_fifo_full,
SA5_performant_intr_pending,
SA5_performant_completed,
};
struct board_type {
__u32 board_id;
char *product_name;
struct access_method *access;
int nr_cmds; /* Max cmds this kind of ctlr can handle. */
};
#endif /* CCISS_H */